Jump to content

2014+ Lowering / Drop Kits

mjw930

By mjw930
in Modifications & Accessories

 Share

Recommended Posts

qwank Senior Enthusiast

qwank

Posted
Posted

I'm having a hard time finding drop spindles for a 2017 4x4 with stamped steel lower control arms. McGaughy's says theirs only fit 2wd and no one else seems to make them.

  • Like 1
  • Replies 3.4k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Heavy_Static
Heavy_Static

A few pics from last week:    

bakerrr
bakerrr

First post here Picked her about 2 weeks ago couldn't wait to start modifying it. Just installed Belltechs 4/7 drop this weekend It's low enough for the time being ??  

Nasty
Nasty

Posted Images

Nasty Senior Enthusiast

Nasty

Posted
Posted

I think crown is the only ones who have the spindle right now for avv arms and 4wd

qwank Senior Enthusiast

qwank

Posted
Posted

You have the new control arms?

yes, I have the stamped steel arms
4itodd Enthusiast

4itodd

Posted
Posted (edited)

Got that back end down ! Put a shackle and took out the block it lowered it about 3 1/2" ..: I don't know why the hell they sit up so high in the. Back !

Edited by 4itodd
  • Like 2
qwank Senior Enthusiast

qwank

Posted
Posted

Got that back end down ! Put a shackle and took out the block it lowered it about 3 1/2" ..: I don't know why the hell they sit up so high in the. Back !

did you do anything to the front?

Nasty Senior Enthusiast

Nasty

Posted
Posted

I wouldn't think so as these trucks are almost 4" higher in the rear stock

qwank Senior Enthusiast

qwank

Posted
Posted

I wouldn't think so as these trucks are almost 4" higher in the rear stock

 

I took the blocks out from under the rear springs but I'm afraid if I do shackles before I get spindles it will look higher in the front.

 

17truck_zps38pf1zgt.jpg

  • Like 1
Nasty Senior Enthusiast

Nasty

Posted
Posted

It'll sit level. The rear fender is actually lower than the front and right now the rear fender is higher than the front

4itodd Enthusiast

4itodd

Posted
Posted

No I didn't do anything to the front . It's about level now 1/4-1/2" higher in the back .. looks 10xs better

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,909
    Total Members
    8,960
    Most Online
    DWic
    Newest Member
    DWic
    Joined

  • Who's Online   5 Members, 0 Anonymous, 703 Guests (See full list)

  • Latest Articles

  • Posts

    • PBNB
      Tire pressure for 37s

      By PBNB · Posted

      Do you think this width might affect the chalk test with a higher pressure closer to 65psi? I think lowering the pressure makes sense to get the tread to lay flatter
    • asilverblazer
      My First Project and GMC has me stumped

      By asilverblazer · Posted

      I had an alternator fail that was shorted internally in such a direct fashion in addition to the larger gauge cables that it appeared like a VERY dead battery. Granted I think the car did power up, it definitely wouldn't start.   Rodent damage to wiring?
    • asilverblazer
      Towing In Loose Gravel

      By asilverblazer · Posted

      ... I don't think he could.
    • asilverblazer
      Towing In Loose Gravel

      By asilverblazer · Posted

      Using experience to justify bad advice is lazy and typical of someone incapable of articulating why their advice is prudent.    This immediately sets off the BS alert and the advice that followed certainly qualified.   Asking an idiot for help getting out of dumb situations because he is an expert... at getting himself into dumb situations.   Unless I've been living in an alternate universe - the first thing everyone does when getting into a sticky situation is shift to a higher gear 🤨.   Of course not, the torque multiplication, mechanical advantage and finer control typically afforded by the lower gear is far better suited for this scenario.   There ARE scenarios where a higher gear MIGHT be appropriate determined more by the drivers ability to control EXCESSIVE wheel spin versus applying torque to the ground.
    • Atlas
      Towing In Loose Gravel

      By Atlas · Posted

      I'm not sure I agree with "extreme" low speed, high torque sentiment here with regards to the prescribed use of low range. How about...whenever it's needed?   A 2.72:1 transfer case and whatever differential gears these Silverados have (3.42's, maybe?) aren't producing "extremely" low crawl speeds. Or insanely high torque multiplication. Even with the 1st gear in these newer transmissions. But it does provide mechanical advantage and potentially better control at slower speeds. And with extra weight or towing, I think it adds mechanical sympathy for the truck as well.   Plus, traction control and the other assists generally turn off when you shift into low range. Those aren't needed here, they'll work against you if you need wheel spin. In high range you'll need to figure out how to turn off the various modes those assists provide. Depending on the vehicle, those things don't all automatically turn off or turn completely off.   While I agree that a farmer might have some great practical experience, a recommendation to "always" using one gear isn't very informed advice. If the farmer had said WHY and could explain the physics behind his prescriptive "always" I'd definitely listen. The way he's described here makes it sounds like he could either be uninformed or is telling everyone what worked for him, not necessarily that there could be a more advantageous way about things.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...