Jump to content

Drop in liner


Recommended Posts

Posted

Where is the best place to purchase a drop in bed liner until I can get my bed sprayed. I've searched around online and seem to have a hard time locating a drop in liner, for a 2015, with tie downs. Anyone have a good "parts" website?

 

 

Posted

Honestly, you are better off with no liner than a drop in.

 

Drop in liners just move around and vibrate, and since dirt always gets underneath, in a very short amount of time you will end up with paint rubbed right through down to bare metal. Scratching the paint in the bed with a few objects now and then is better than a drop in. They will scuff the hell out of your bed anyways to apply a spray in liner, so unless your going to let your box rust before they can spray it on, it won't matter.

Posted

I've run drop in Pendaliners in every one of my trucks since the early 90s. Never had any issue with the paint rubbing off in the bed... and I had my 01 and 07 for well over 5 years each.

 

Sounds like sprayin liner propaganda to me.

 

That said... Spray in liners are a lot tougher if you use a truck for heavy duty for sure.

Posted

Where is the best place to purchase a drop in bed liner until I can get my bed sprayed. I've searched around online and seem to have a hard time locating a drop in liner, for a 2015, with tie downs. Anyone have a good "parts" website?

 

I know some guys that bought Duraliners off the web. They come in pieces and you can install it yourself. Another option is to buy a bed mat (Bedrug mat, not the whole liner, for example) and us that until you get it sprayed.

Posted

Why spend the $$$ on a drop-in only to replace with a spray-in? Just use a chunk of carpet or get a cheap rubber mat. That's my $0.02 anyway.

Posted

just curious why there's a problem getting a spray in done quickly? my last truck (my current came with it) I found a place and had it done the following weekend.

Posted

I've had a drop in liner in my last three trucks with absolutely no problems. I will put one in my next truck.

Posted

Dropping $500 on a spray in liner vs. about 150-200 for a drop in is the whole reason....never thought about a bedmat, that would probably make more sense than spending even more on a bed liner.

Posted

I've become a spray-in fan, but before conversion it was always are 'roll-in' rubber mat. Protects the floor, stuff doesn't slide, and the tie downs are not covered.

Posted

Have always used drop in liners, usually pendaliners with a pad from a truck accessory store and the GM drop in on last two trucks.

 

Have never noticed box rust, and I doubt that abrasion from the liner could be 1/10 as bad as me using a bare back end. I like the drop ins because they keep your stuff above water and snow. (throw my ice shanty in back in the winter, canoe and kayak in summer)

 

They're easy to clean out as well.

 

I don't care what anyone buys, but I'll never do anything but drop in because I throw wet stuff in back year round.

Posted

I am also a fan of drop in liners but did not like how my GM version was installed with sheet metal screws when I went to pick up the truck. What is done is done though. Yes drop in may scuff the paint up but I have never had one cause rust problems. My work trucks do not have any liners and sharp tools are always being drug out of them taking paint with them. We never have any rust issues with that either. I just don't like how sticky a spray in liner can be.

Posted

So the main question becomes is there a good place online to purchase a drop in liner?

 

Have you checked your local craigslist page? That's where I bought mine for $75, it was a like-new takeoff that a Ziebart spray-liner shop was selling. I've also seen a local Line-x shop list them on craigslist too for only $50. And then I've seen private owners trying to sells theirs too from their new trucks.

Posted

So the main question becomes is there a good place online to purchase a drop in liner?

 

If you have the 6'6" bed, $198 shipped seems fair to me:

 

https://jet.com/product/detail/aafec044baf94a9d868a4e942bfe10c8?jcmp=pla:ggl:vehicles_parts_a1:vehicle_parts_accessories_motor_vehicle_parts_motor_vehicle_frame_body_parts_a1_other:na:na:na:na:na:2&code=PLA15&k_clickid=e8cdebe8-54b4-4fa4-9a4a-3cc0e355dbff&gclid=CLqCuP3i6skCFQyFaQod7PQKMw

 

I've bought from Jet and they have fast shipping.

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.6k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    343,007
    Total Members
    8,960
    Most Online
    Brendan C
    Newest Member
    Brendan C
    Joined
  • Who's Online   0 Members, 0 Anonymous, 1,067 Guests (See full list)

    • There are no registered users currently online
  • Latest Articles

  • Posts

    • You're better read than that Atlas. 😏   British science fiction writer Arthur C. Clarke formulated three adages that are known as Clarke's three laws, of which the third law – that "any sufficiently advanced technology is indistinguishable from magic" – is the best known and most widely cited.   Stribeck and the pivotable Hersey Number isn't voodoo nor snake oil. That part is physics. It's what marketing and bean counters do with it that is snake oil and voodoo.    Stribeck is the relationship between Hersey and the Coefficient of Friction. Within the Hersey Equation if viscosity and viscosity is 'Dependent' on.......heat.......and.......viscosity index or the temperature to viscosity slope.    Specifically Hersey is the viscosity AT THE TEMPERATURE IN THAT LOCATION FOR THAT SLOPE.   Hydrodynamic lubrication exist when the film thickness in the location is 3X the Ra roughness of the surface. This is irrespective of the hardness of the substrate. To obtain that thickness X viscosity is required for Y velocity at Z load. That's a lot of moving parts. It is also impossible to maintain in an ICE but nearly possible with a turbine under constant load.    What does that mean? Error heavy and operate light. Wear is inevitable but the rate of wear and the milage obtainable are a function of prevailing conditions and HABITS. The only penalty is viscous drag and at fractions so low as to be well worth the effort. Double the life, half the manufacturing carbon foot print. Greed is the only impediment.    The materials generated by SwRI are the RESULT not an estimation or a hypothesis.    Don't delude yourself sir, EV's have as many pitfalls as ICE's. We just don't know what they are yet and it will take longer to sort as MARKETING and GREEDY CEO's have had more time to polish the turd they are selling. 
    • You can always count on greed to prey on ignorance and stupidity.    Friend bought a 2019 Ford Flex and asked me about using Valvoline R&P 5W30 in it. Told him give the miles on it and the fact it wasn't yet using oil that it was a good plan. He uses a Valvoline quick change shop for his oil service.   First they tell him that isn't the oil the OEM recommends. He told them he didn't care what the OEM thought. Then they floated the, "But it will void your warranty"    His reply was it's a 2019, there is no warranty and informed them their knowledge of the law was lacking.    Then they tell him 'But it will ruin your motor"!.    Mine to ruin he says. Finally they give in and charge him 150% the semi-syn price    Point it the brainwash is so embedded that even the service industry is drunk on their swill. The public is right behind them. Echoing the same lies on every forum and media platform. If the end goal is indeed EV then I'd say that ship is about built. 
    • Diesel hit $6.00 here today at the truck stop.   Payed $2.79 for E85 today too.
    • Thanks for posting, I'm sure it will help someone
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...