Jump to content

Trailer lights don't work

Jimmyjam
 Share

Recommended Posts

SuperAllTerrain Enthusiast

SuperAllTerrain

Posted
Posted
I've got a 2016 CC LTZ short box and no matter what trailer I pull i have no drivers side turn signal or brake light. I even rewired my trailer (and my buddy hooked up his truck to it and it works fine) and have pulled my buddies boat( didn't work on mine). Still doesn't work. I am bringing it in to the dealership on Monday. But just was wondering if anyone else has had the same issue?
 
 
Sent from my iPhone using Tapatalk

Did you figure the problem I have the same issue


Sent from my iPhone using Tapatalk
SuperAllTerrain Enthusiast

SuperAllTerrain

Posted
Posted
I have a 16 Silverado with the same problem there are 2 relays in the circuit board that controls each side for the brake and turn signal under the fuse box that if the fuse don't blow it will burn the relay up I just changed the whole fuse box out cost me $232 and about 10 minutes and I got mine working again. Chevrolet has a bulletin out about using cheap fuses causing a lot of trouble. If I can help with pictures message me. Also my camper had a short I used a cheap fuse and that's what took mine out.

Yes please help out with pictures I’m having the same issue


Sent from my iPhone using Tapatalk
Michael04 New Member

Michael04

Posted
Posted (edited)

Easiest way to see if the relay is burnt out is to cut the switch on without starting your truck flip the turn signal to either left or right pop the hood and in the fuse block you should be able to hear the relay clicking if you don't that's more than likely your problem. If you look close above the 2 10 amp fuses the fuse for one of the turn signal is melted

IMG_20200101_193354352.jpg

Edited by Michael04
  • 2 months later...
  • 3 months later...
bububabo New Member

bububabo

Posted
Posted

 Jimmyjam, did you ever figure the problem out?

I've got the same issue lately and I think it's the fuse too.

Pain in the butt though.

 

  • 9 months later...
Hugrafix New Member

Hugrafix

Posted
Posted

I have a 2015 Silverado and bought a boat and the trailer lights werent working.  I got the left blinker/brake working and found the issue was the ground, once I cleaned the mounting area the blinker and brake started working.  This is where I made my mistake, as the blinker was still blinking I was getting all my other wires fastened, I touched one of the wires to the trailer and it shorted  both the blinker and brake lights on the left side.

 

I bought all new lights and wiring as they were mismatched anyhow and rewired the trailer, when I tested still no blinker or brake on left side.  After checking everything, I found out about the trailer FUSE which when I checked it was blown.  I ordered fuses last night and replaced FUSE 14 which is for the trailer left turn and brake, tested again and no change, still no left turn or brake.  

 

All lights on Right side work and running lights on left side.  I also grounded to trailer with jumper cables just to make sure that was not the issue.  What can I do next to get my issue resolved?

  • 4 weeks later...
Tech Junky New Member

Tech Junky

Posted
Posted

Having the same issue on my 2017 Denali 2500HD. Tried turning the auto lights off and turning on manually but that didn't work. Currently only the right trailer turn signal does not work. Checked the fuse and it's good. Tested for voltage at the fuse and nothing. Turning on the left turn signal I can hear a click like a relay is being engaged and disengaged as the light blinks but do not hear that when the right signal is on. Thinking it's the 'engine compartment fuse block'. No signs of melting though. Thankfully I have an extended warranty and that is covered. Will post once I have it diagnosed and fixed. Will be a few weeks.

Ravenkeeper Senior Enthusiast

Ravenkeeper

Posted
Posted
4 hours ago, Tech Junky said:

Having the same issue on my 2017 Denali 2500HD. Tried turning the auto lights off and turning on manually but that didn't work. Currently only the right trailer turn signal does not work. Checked the fuse and it's good. Tested for voltage at the fuse and nothing. Turning on the left turn signal I can hear a click like a relay is being engaged and disengaged as the light blinks but do not hear that when the right signal is on. Thinking it's the 'engine compartment fuse block'. No signs of melting though. Thankfully I have an extended warranty and that is covered. Will post once I have it diagnosed and fixed. Will be a few weeks.

Have you metered out the receptacle on the truck?  Or get a receptacle tester.  If the receptacle works as advertised, then it's the trailer.

 

Amazon.com: CURT 58270 7-Pin RV Blade Trailer Wiring Towing Vehicle Socket Tester: Automotive

 

Four-Way Trailer Light Tester

  • Like 1
  • 1 year later...
  • 3 months later...
paul Sufady New Member

paul Sufady

Posted
Posted
On 5/10/2019 at 9:32 AM, Michael04 said:

I have a 16 Silverado with the same problem there are 2 relays in the circuit board that controls each side for the brake and turn signal under the fuse box that if the fuse don't blow it will burn the relay up I just changed the whole fuse box out cost me $232 and about 10 minutes and I got mine working again. Chevrolet has a bulletin out about using cheap fuses causing a lot of trouble. If I can help with pictures message me. Also my camper had a short I used a cheap fuse and that's what took mine out.

 

  • 3 years later...
SquattedChevOnBlack Enthusiast

SquattedChevOnBlack

Posted
Posted
On 4/26/2021 at 3:02 PM, Tech Junky said:

Having the same issue on my 2017 Denali 2500HD. Tried turning the auto lights off and turning on manually but that didn't work. Currently only the right trailer turn signal does not work. Checked the fuse and it's good. Tested for voltage at the fuse and nothing. Turning on the left turn signal I can hear a click like a relay is being engaged and disengaged as the light blinks but do not hear that when the right signal is on. Thinking it's the 'engine compartment fuse block'. No signs of melting though. Thankfully I have an extended warranty and that is covered. Will post once I have it diagnosed and fixed. Will be a few weeks.

💀*dies waiting for the warranty diagnosis and fix*

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • KARNUT
      Towing In Loose Gravel

      By KARNUT · Posted

      First off use it in the way you’re more comfortable. In working in off road situations most of my life I used 4WD low range very little. In most cases when equipped I used auto 4WD. If I wanted maximum control going up and down very steep terrain  I used low range. Especially if I was driving a diesel. Same with very rutted terrain. In very muddy or snowy conditions I wanted momentum so high range worked well for that. With gravel ramps with limited traction I would try high range first. I would want smooth even increasing speed if I was fighting traction. Low range could give you too much to the wheels breaking traction trying to move. 
    • Z45
      Towing In Loose Gravel

      By Z45 · Posted

      Having owned 4wd vehicle since the 1970s I find there are varying opinions on how to use 4wd, every owner is an expert in their minds.  IMO, 4LO is the appropriate gear and what I would use,  You have to feather the gas to avoid spinning tires and the lower the gear the better chance.  But like I said you will find those that think their method is best.  I live near a boat launch.  Yesterday there was a new Ford Maverick pulling out a pontoon boat almost 2x its size, they had no problems and they don't have a LO range.   True story. One winter day not long ago I was coming out of small town post office and there was a F150 4wd parked in front and was stuck foot deep snow ruts. I knew the lady so I asked her to put it in 4wd (wondering why in the middle of a 2-day snow storm she wasn't).  Her reply surprised me, "my husband" (the expert) told me not use that because it uses too much gas. She finally got unstuck spinning in 2wd which likely used more gas than not.  
    • dna9656
      New to Me 2010 SLE (Quirks, Issues)

      By dna9656 · Posted

      Your tire pressure issue may just be batteries, you can reset them using tge Ing switch (I think) and the owner's  manual. ChatGTP will b e a faster, better help than Google.
    • Another JR
      Towing In Loose Gravel

      By Another JR · Posted

      The thinking is that starting out in a higher gear makes it easier to avoid applying excessive torque when pressing the gas pedal. In a modern 4wd truck with 4 low and a limited slip or locking rear end, I would use 4 low and try to crawl up the ramp. Sometimes if they are too slippery, you have to back up to let the boat have some bouyancy, and then accelerate briskly to get some momentum to help you pull the through the slippery parts. 
    • XY74
      Roll up bed cover experiences

      By XY74 · Posted

      I have a Retrax pro that I first had on my 2020 chevy and transferred it to my current GMC.  It stays in the garage most of the time, so hard for me to judge it's long term weather resistance.  It still works perfectly, been very durable.  It doesn't see oil patch usage, but it's not a mall queen.  It keeps most things mostly dry (small leaks) and the security of it is enough to slow someone down but not keep them out for long.  I would buy one again, it works for me.     

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...