Jump to content

2016 Silverado 5.3 CHEAP Exhaust Route


Chevrojayy97

Recommended Posts

Posted

I know there's a huge struggle with these trucks and finding a nice performance exhaust system. Before buying one, consider what I've done for mine. I took it to the local muffler shop and asked what he recommended. I like the growl of a V8 and I like to hear it, so I wanted to go as loud as possible but keep a nice tone. For me, the owner recommended an 18" Glasspack, Y-Pipe, and Dual 4" Tips at a 45 degree exit. I'll post some links below for sound reference. Best part? $300 Installed and I couldn't be happier. I get compliments on it everywhere I go, and sounds 10x better than the $1,000 bolt on systems. Kept all the cats in place, just replaced from the muffler back. Hope this helps!

 

Warm Start and Revs:

 

 

Cold Start:

 

Posted

That will wake the neighbors haha. Thanks for posting. How loud is it cruising down the road and on the highway? I was looking into doing this same basic setup, except using aero exhaust instead of glasspack

Posted

Nice. Similar to what I did but I used a Flowmaster outlaw extreme muffler and just dumped it after the muffler

Posted

That will wake the neighbors haha. Thanks for posting. How loud is it cruising down the road and on the highway? I was looking into doing this same basic setup, except using aero exhaust instead of glasspack

It does have bit of drone in "V4" mode but it is not bad at all in "V8" mode. I've taken it on several road trips and my passengers haven't complained about it yet. Aero mufflers are NICE. If you go that route, I'd love to see how it turns out, as I will be doing true duals with long tube headers down the road.

Posted

I am rocking a super 44 and res delete on my 16 if you order from JCW when they have a sell its $69 shipped (org $86?), depending on shop or diy it ran me 190$ instilled ($130 for the instill including res delete) i also kept my flapper valve operational

 

Cold start is louder then stock

Idle nice deep rumble but quiet

Cruising speeds it does have slight drone, according to my grandma who hates loud exhausts she loves it and the drone is pretty quiet

Posted

I am rocking a super 44 and res delete on my 16 if you order from JCW when they have a sell its $69 shipped (org $86?), depending on shop or diy it ran me 190$ instilled ($130 for the instill including res delete) i also kept my flapper valve operational

 

Cold start is louder then stock

Idle nice deep rumble but quiet

Cruising speeds it does have slight drone, according to my grandma who hates loud exhausts she loves it and the drone is pretty quiet

That's not bad. The reason mine was $300 was because of the piping and 4" tips I opted to get for looks and a slight change in sound over just replacing the muffler.

Posted

Thank you i will probably do a custom corsa dual catback or dual super 44/super 10 eventuality but i am just enjoying hearing that 5.3 make sweet v8 noise it beats the prius sounding that the factory gave it

 

put it this way my cuz spent $330ish on the same setup (super 44 single in/out) for his 16 F150 2.7 eco and that was muffler swap only (he still has the res)

Posted

Nice. Similar to what I did but I used a Flowmaster outlaw extreme muffler and just dumped it after the muffler

 

take it you don't have the flapper?.. you get the drone in V4 everyone hates?

Posted

Correct, no flapper. I get the drone but it doesn't bother me. I will eventually install a flapper though when I come across one.

Archived

This topic is now archived and is closed to further replies.

  • Latest Articles

  • Posts

    • The part # is 84520447, mine does not have the cooled seats but I'm willing to possibly change the cover and foam if needed.   I tried that site and a few others,  added to cart and then paid. About an hout later I received a refund stating it has been discontinued. 
    • Thought I would add to what Bruce answered, not only do the HD models use the torsion bar system, there are I believe 5 different torsion bar spring ratings that are all physically interchangeable with all the HD trucks going from a two wheel drive 2500 all the way up to the duramax or a gas engine truck with a snow plow prep package front end weight capacity that use the maximum sized torsion bar. It starts from a 4400 lb rated set in 400 lb increments up to 6000 lb. If one wants to fine tune the ride for a certain truck application they can swap out the torsion bars. 
    • First off pay close attention to what Newdude pasted as he is a GM tech !.    I have a couple of questions which might cross off some questions others on this forum would be wondering about as well. So when was the engine oil changed prior to this trip, was it almost brand new oil or did it already have a fair bit of use on it before you started the trip.   Did you check the oil level on flat ground and was it at the full mark just before leaving on this trip which I gather from google map is about 700 miles or so. Why I ask and this is not the first time in history that has happened, that either a dealer or some other shop changed the oil on the vehicle and the vehicle left the shop and the owner ( you ) assumed the engine oil was full but in reality the person who changed the oil simply did not put enough oil into the engine .. it happens !. Also that a shop put the wrong viscosity oil in and an engine was not happy with that thinner viscosity and oil got past the rings at a higher rate than the proper viscosity. Not to mention if there was any leaking out of a drain plug or the filter gasket etc. 
    • You could, although in the end it really doesn't make much difference what comes out in exact terms since it comes down to putting enough back in so that there is enough volume so that something flows back out once the trans is up to temp for the check procedure. I presume your putting a pan on that has a drain plug but its probably the same pan mold/size as at least a while back no extra volume pan was made for the gas truck version due to the exhaust cross over pipe issue. All I can say as per volume I put back in and this was based on changing out the filter as some is trapped in it that does not come out until its removed because of the way its made inside and my truck had sat over night with the trans having been hot when shut down and dripping internally before I pulled the pan. I went off of what the trans shop suggested as a minimum volume he found worked which was 9 1/2 quarts and I had enough flow out of the stand pipe that I knew I was right on the money once it slowed to a dribble and never wasted hardly any oil but it would be totally fine to throw in a full 10 quarts too. I guess personally I wouldn't ruin a perfectly good pan by drilling a hole in it, not with the cost of replacement pans up here or the dorman one anyway with the drain was 500.00 when I priced one out a while back, totally stupid.    I might not have said before but this trans oil type really expands with heat and I think its been said on this forum and the trans shop said the same so I wanted to try and hit the lower temp of the range vs at the top or go shooting above it as that would allow more oil to flow out which wouldn't be ideal. 
    • Since I am going to be replacing the pan, I am just going to drill a hole in the original to drain it so I will be able to catch the fluid easier and measure how much I took out.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...