Jump to content

Drop in mpg

Chevytrk15
 Share

Recommended Posts

L86 All Terrain Senior Enthusiast

L86 All Terrain

Posted
Posted

Does your area run winter gas? They just started switching a bit ago. Also could be your intake is starting to gum up if you dont run a catch can. Increased warm up/idle times etc.

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Chevytrk15
Chevytrk15

I have had my 2015 Silverado 1500 crew 5.3 for the past year. One of the many things that I loved about my truck was the fuel mileage. I always averaged 19 to 21 mpg. I am usually driving about 65 mp

Sean Neilan
Sean Neilan

I get the exact same mileage on 89 or 91/93 as I do on 87

Sean Neilan
Sean Neilan

My 2015 5.3 has 25k miles and a lifetime average of 16.1 mpg. I've noticed a 1-2 mpg drop when the temp drops below 45-50 degrees out. These trucks seem pretty sensitive to the temp (I've noticed th

redwngr Senior Enthusiast

redwngr

Posted
Posted

Add about 1 gallon of 121 octane to every third or fifth tank and you will be fine. I run premium in my truck year-round and my gas mileage never fluctuates

 

 

Sent from my iPhone using Tapatalk

But you're in Georgia.

 

Winter changes to fuel are regional.

Haus_Z71 Enthusiast

Haus_Z71

Posted
Posted (edited)

10 mpg is definitely rough. I appreciate all the input. My main thing is I just want to make sure there is nothing wrong with my truck. And I would like be to just know why and if upgrading the octane would do anything. If 93 would bring my mileage back up

I guess the obvious is probably already covered, but have you had your air filter replaced?

 

What did they do with your service? Just oil change? I would make sure they used 0W-20.. but a GM service department should know what your truck recommends.

 

These Direct Injection engines do have a lot of build up on the intake valves. I believe the dealers recommend this service at 30k miles, and it should improve fuel economy. HOWEVER, I am very skeptical of this service, because after I had it done, my cats failed from so much gunk being cleared out. Dealer had to replace the cats under warranty.

Edited by 2015_Sierra
dagwood2001 Enthusiast

dagwood2001

Posted
Posted

I have also had issues with my gas mileage over the years. I had a 2014 for 2 years and am currently about a year and a half into a 2015. Both totally stock with the 5.3L V-8.

 

I don't drive all that much (don't know if that has any impact, my 2015 only has 6100 miles on it) and both trucks, amazingly, have averaged 13.4 MPG, exactly. I'm not thrilled with that but I really only need to fill it up every 10 days or so, and gas is hovering around $2-2.15/gallon (although with the Giant discount tied to grocery purchases I usually pay about .75 cents a gallon every third fill) so it really isn't the end of the world but I sure seem to get worse mileage than most?

 

I'm in Philly BTW where it either seems to be 100 or 25 degrees.....

Sean Neilan Enthusiast

Sean Neilan

Posted
Posted

I have also had issues with my gas mileage over the years. I had a 2014 for 2 years and am currently about a year and a half into a 2015. Both totally stock with the 5.3L V-8.

 

I don't drive all that much (don't know if that has any impact, my 2015 only has 6100 miles on it) and both trucks, amazingly, have averaged 13.4 MPG, exactly. I'm not thrilled with that but I really only need to fill it up every 10 days or so, and gas is hovering around $2-2.15/gallon (although with the Giant discount tied to grocery purchases I usually pay about .75 cents a gallon every third fill) so it really isn't the end of the world but I sure seem to get worse mileage than most?

 

I'm in Philly BTW where it either seems to be 100 or 25 degrees.....

If you're just driving around town especially in a congested area it'll be bad. I'm on Long Island and if I'm driving around town and no highway I'll get 12-14 depending on how many red lights I get stuck at.

66deadhead Enthusiast

66deadhead

Posted
Posted

Ok, I gotta comment on this cause I'm experiencing the same thing on my 2016 at 11,500 miles. It seems like since it's gotten colder out my gas mileage has took a dive, and it also seems to be running a little rougher at idle too.

I was averaging about 17-18 mpg back and forth to work, and now I'm getting about 14-15 mpg, I gas up at the same station for almost every fill, run medium grade, and it's a top tier fuel (Exxon) I been attributing some of this to using the remote start in the mornings. Can't explain the rougher idle though. I thought about shooting a can of seafoam or CRC intake/Throttle body cleaner in it , but am hesitant to do so as I don't want it to possibly throw a code. I did install a catch can recently, at about 11,000 miles. But the mileage was already dropping off before that. I spoke to the dealer and they recommended a upper induction cleaning and throttle body cleaning at about 37,000 miles. Yep... 37, 000 miles, 1000 miles after the factory warranty runs out. I found this hilarious, and cracked up right in their faces when they told me this. They also told me I really don't need a catch can on it, as the Silverados are not really prone to valve coking.... Yep, you heard that right... Yet at 37,000 they wanna do a upper induction cleaning. Lol. They did say the Chevy Traverse has a huge problem with intake crud though and attributed that to poor engine design. I am Not trying to turn this into a catch can thread, just stating where I'm at with this truck now, and am wondering the same thing about the gas mileage and why it's dropping off so quickly since it's gotten cold out. And At this point and time, I would have to agree that the colder weather definitely has something to do with mileage, and how the truck runs. But I am also wondering if it's partially because of any crud that may have built up in the engine already. ....or maybe it's a combination of the 2 ?? Guess one day it's warmer on a weekend, I'll get ballsy and shoot a can of cleaner through it and see what happens if it continues to plummet.

Eddie 70 Senior Enthusiast

Eddie 70

Posted
Posted

One thing I would do is check my oil level and make sure it is not over the top line on the dipstick. In fact GM recently backed off on 8.5 quarts of oil and dropped back to 8 which should probably be about halfway between low and full on the dipstick. Check your tire pressures and make sure they are at the recommended pressures at least or where you like to run them. I run mine at about 35 PSI. Check the air filter and see how it looks.

 

My 2014 has 70000 miles on it and I am currently averaging 23.XXX mpg for the last 27k miles. I bought the truck with 42k and that is when I started tracking it.


One thing I would do is check my oil level and make sure it is not over the top line on the dipstick. In fact GM recently backed off on 8.5 quarts of oil and dropped back to 8 which should probably be about halfway between low and full on the dipstick. Check your tire pressures and make sure they are at the recommended pressures at least or where you like to run them. I run mine at about 35 PSI. Check the air filter and see how it looks.

 

My 2014 has 70000 miles on it and I am currently averaging 23.XXX mpg for the last 27k miles. I bought the truck with 42k and that is when I started tracking it.

Boardmember Senior Enthusiast

Boardmember

Posted
Posted

I assume or hope everyone is calculating this manually, not relying on the not-so-accurate DIC...

Eddie 70 Senior Enthusiast

Eddie 70

Posted
Posted

I assume or hope everyone is calculating this manually, not relying on the not-so-accurate DIC...

 

 

I use aCar app on my phone. Input the mileage and gallons added to the tank and it does the calculations for you. It's always about 1 - 1.5 MPG lower than the DIC.

Sean Neilan Enthusiast

Sean Neilan

Posted
Posted

I assume or hope everyone is calculating this manually, not relying on the not-so-accurate DIC...

I calculate mine manually every tank and it has been within +\- .1 of the DIC.

Sean Neilan Enthusiast

Sean Neilan

Posted
Posted

Ok, I gotta comment on this cause I'm experiencing the same thing on my 2016 at 11,500 miles. It seems like since it's gotten colder out my gas mileage has took a dive, and it also seems to be running a little rougher at idle too.

I was averaging about 17-18 mpg back and forth to work, and now I'm getting about 14-15 mpg, I gas up at the same station for almost every fill, run medium grade, and it's a top tier fuel (Exxon) I been attributing some of this to using the remote start in the mornings. Can't explain the rougher idle though. I thought about shooting a can of seafoam or CRC intake/Throttle body cleaner in it , but am hesitant to do so as I don't want it to possibly throw a code. I did install a catch can recently, at about 11,000 miles. But the mileage was already dropping off before that. I spoke to the dealer and they recommended a upper induction cleaning and throttle body cleaning at about 37,000 miles. Yep... 37, 000 miles, 1000 miles after the factory warranty runs out. I found this hilarious, and cracked up right in their faces when they told me this. They also told me I really don't need a catch can on it, as the Silverados are not really prone to valve coking.... Yep, you heard that right... Yet at 37,000 they wanna do a upper induction cleaning. Lol. They did say the Chevy Traverse has a huge problem with intake crud though and attributed that to poor engine design. I am Not trying to turn this into a catch can thread, just stating where I'm at with this truck now, and am wondering the same thing about the gas mileage and why it's dropping off so quickly since it's gotten cold out. And At this point and time, I would have to agree that the colder weather definitely has something to do with mileage, and how the truck runs. But I am also wondering if it's partially because of any crud that may have built up in the engine already. ....or maybe it's a combination of the 2 ?? Guess one day it's warmer on a weekend, I'll get ballsy and shoot a can of cleaner through it and see what happens if it continues to plummet.

As me and others have pointed out in here already these trucks seem very sensitive to cold and when the temp drops below 45ish there is a noticeable (and in some cases drastic) drop in mpg

MySilverado180 Enthusiast

MySilverado180

Posted
Posted

Maybe my story will help. I have the 5.3 with 8 speed and I have a lifetime mpg of 18, and this includes some towing. I average 19-20 on my daily drive to work (mostly highway). It does go down some with the cold.

 

I use Oil Life Monitor (OLM) to know when to change my oil. Get it done just above 0%. I track my mpg very closely and started noticing the mpg would go way down towards the end of my oil life. This was only when I was using up the free oil changes the dealer gave me. I have since switched to doing oil changes myself, and I use Mobile 1 fully synthetic 0W-20. What a difference in mpg. There's no longer a dropoff in mpg toward the end of my oil life. Can't explain it, just my observation.

last truck Enthusiast

last truck

Posted
Posted

1st he DIC doesn't measure the amount of fuel flow, it measures miles to gauge readings so we all know the first 1/8 tank lasts longer than the middle 1/4 tank.. 2nd did this drop occur about the time the truck was leveled, lifted or new tires wee added?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • ManyCamaroz
      2024 SILVERADO 3500HD DURAMAX CLOGGED DPF AND WONT CONNECT TO TRAILERS

      By ManyCamaroz · Posted

      I had an issue with a new 1985 Z-28 some years ago. The 4WDB's were less than adequate when purchased IMO.  I had taken it in for small warranty services and asked them on three occasions to check them. Each time is was "could not duplicate on the service ticket. The warranty ran out about a month after my last visit and had to take it back for warranty rework. I again complained about the brakes. Well, low and behold, this time they determined the rear calipers were sticking and gave me a quote to repair. They had records as well as O had receipts of each time complained about the brakes while still under warranty. My dad was a life long body shop owner and told me to keep my cool and tell them that I wanted to speak to the GM Regional District Manager. The service manager disappeared for a few minutes, came back and told me they would replace the calipers free of charge. 
    • Anita's2015
      Travel Trailer 2024 2500 HD 6.6 Gas Engine ?

      By Anita's2015 · Posted

      Towing a 2022 Lance 24 ft travel trailer with our 2021 GMC Sierra 2500HD, gas.  Loaded, trailer is about 6,000 lb.  We get up to 10 mpg at 55 mpg, such as I-5.  Pleased with the combination.
    • Chuck FB
      Correct way to service 2024 l8t allison trans?

      By Chuck FB · Posted

      I decided to give it a shot and see what sort of a gong show it would be to a pan drop themed oil change on my 2025 gas truck with the 10 speed. All indications I had seen so far was that there was no way that pan was coming out of there due to the cross over exhaust pipe not allowing enough clearance for the back end of the pan to duck out from under the valve body since it hangs lower than the pan to trans mount flange and certainly the filter does. I never touched any of the exhaust mount hardware at all, be that the engine manifolds to Y pipe, the bracket on the side of the transmission, or the two bolt flange further back behind the trans/transfer case. I put the truck up on four jack stands as there was no way I was going to struggle with that lack of clearance under the truck. The truck was cold as it had sat over night so all the trans fluid had drained to the pan, so I drained the bit of oil that would come out of the level check plug at the bottom near the front of the pan and put the plug back in to reduce the ensuing mess after that. Then took out all but one bolt front and rear and then pushed up on the pan and took out the remaining two bolts and then let the front of the pan tilt and spill out most of its contents into a drain pan. I then popped the pan gasket off its two locating nubs and kicked it a bit to the left side so it was no longer on the flange of the pan to get all the clearance I could and managed to get the pan slipped out of there by swinging the front of the pan to the right but keeping the rear part of the pan inline if not slightly to the left of its mounting flange area and lifting the front of the pan enough to keep the rear part of the pan low enough that allowed the pan to "JUST" slip out without forcing anything. I installed a new trans filter and seal and as per GM instructions on this site I torqued the two bolts to that 44 inch pound goal ( they take an 8 mm socket ) In reversing the pan procedure after I had cleaned up the pan both inside and out completely ( touching the outside of a dirty pan and dealing with installing a gasket at the same time would be a disaster ). First I slipped the pan into place and yes it took me a while as it won't go unless its slid in just at the right angles, then once the back of the pan was into the area of the flange mount, I went and got the gasket and then threaded that through the front of the pan and feeding it under the filter etc and finally working it onto the flange of the pan and lining up the two locating nubs to drop into the pan. Then lifted the pan up into place and get a couple of bolts started and check and make sure the gasket is where its supposed to be as the bolts were being put in. I never used any power tools as I don't have any of the whimsy little drive guns, I use what looks like a small screw driver handle with shank that has a 1/4 drive on the end of it and added an extension and those bolts use a 10 mm socket as some times power tools can bite a person if used on delicate parts ( torqued to 80 inch pounds ). Also should note as per rules around pulling the add plug out first, yes I cracked that loose with a 8 mm Allen bit socket on a 3/8 slim head ratchet as there isn't a lot of room to work with there either due to the exhaust on the right side of the trans.    I already had delco ULV oil on hand and of course the quart bottle pump wasn't made for those small cap threads so I had to use some other containers that the pump would fit and keep transferring oil over into them so a wasted exercise there but indeed the small pump did work just fine as ULV oil is thin and easy to pump in summer time weather. I put in 9.5 quarts as per prior minimum recommendation and yes that cut it pretty close as once I had the truck ( off the jack stands so its level ) and the trans oil up to 167f , about 6 ounces came out but a level kit or what have you could throw it off just enough that it wouldn't be enough oil so probably that 10 quarts is a good amount to put in so one doesn't have to add more oil as when its hot I sure wouldn't want to be adding oil so would have to let the exhaust cool. All I do for warming up the transmission is sit there with it in park and rev it to about 2500 rpm and it takes close to 20 minutes to get it up to that lower limit of 167f, weird how it will warm up more doing that then by driving it, I am not real keen on power braking the truck to get the temp up there and don't seem to have to either. By the way I only have 9000 miles on the truck so probably not a very good payback on doing it that soon and the magnets had such a minor thin layer of fines on them so that was good to see and the color of the oil was a darker red then new oil but still looked very good as it should and I've not done any towing with it so its been living a pretty easy life so far. The filter is made in such a way that its next to impossible to pull out the filter media but there certainly was some fines showing up there which makes sense give the trans having to break in.    I hadn't really planned on explaining this much of what I had done since there are various instruction videos kicking around or I think so, as the gist of my message as that by fluke or what have you, for some reason my truck has just enough clearance to slip the pan out from the trans. Of course there is no guarantee that other trucks like this in general will also allow the pan to be taken out without messing with the exhaust as I expect its probably a crap shoot if it will or won't, I was just happy to find out that mine would work and avoid all the other struggling and possibly damaging things in the process,     
    • BCGM
      Fog Lamps 2024 2500 HD

      By BCGM · Posted

      Do you fellas think Fog Lamps would  be a good upgrade for our 2024 2500 HD Custom ? As you probably know it did not come with them ,  Would you put in GM Chevy parts ? Do they get wired up to the switch panel ( Upfitter or whatever the correct terminology is ) on the dash ? Thanks
    • davester
      Looking at ordering a '26 WT because I want a std cab, std bed

      By davester · Posted

      It would depend on what you do to lower it.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...