Jump to content

trailer brake output

GlenS
 Share

Recommended Posts

GlenS Enthusiast

GlenS

Posted
Posted

So I towed my trailer this morning to a jobsite. I unhooked for a bit had some running around to do. Came back and hooked up. I have no output on trailer brakes. the gauge pops up on dash but no matter what I do I get no level indication. Checked fuses they seem ok. test for voltage i rear at plug with brakes on and no voltage. What am I missing. Trailer brake fuses under hood.///???

 

HeliMark Enthusiast

HeliMark

Posted
Posted

So I towed my trailer this morning to a jobsite. I unhooked for a bit had some running around to do. Came back and hooked up. I have no output on trailer brakes. the gauge pops up on dash but no matter what I do I get no level indication. Checked fuses they seem ok. test for voltage i rear at plug with brakes on and no voltage. What am I missing. Trailer brake fuses under hood.///???

 

Unless the truck senses a trailer is actually hooked up, you will not get any brake voltage at the plug. I have had some issue's and usually cleaning the plug has fixed it. Or in a rush, plugging/unplugging several times works.

 

 

Mark

GlenS Enthusiast

GlenS

Posted
  • Author
Posted

Yes I have lights. I took it apart and cleaned it. Seems to be fine now . Out put is back. Wow it is a sensitive system. I understand what you are saying Mark. Thanks for the help guys.

Offcamber Enthusiast

Offcamber

Posted
Posted

This happened to me on my 1500... Usually just making sure the plug is all the way then you need to shut the truck down and restart. This should rest the system so the truck detects the trailer fully. You can get light and no brakes.

MotionMan Enthusiast

MotionMan

Posted
Posted

Dielectric grease. Jam the pins with it. Pack the flat 4 too, in MI with salt it will turn into green dust if you don't.

SouthpawHD Enthusiast

SouthpawHD

Posted
Posted

GM female plugs are known to have loose connections from time to time. On your trailer plug, pinch the trailer brake plugs closer together using a small pliers and you should be all set.

HeliMark Enthusiast

HeliMark

Posted
Posted

The plugs on the newer trucks seem to be a weak point. Clean and pack with the dielectric grease is a good suggestion no matter where you are located.

 

And wholly crap, do not pull the trailer emergency brake to test it when you are hooked up to the truck. Want to talk about sending the truck into an electrical tissy......

 

 

Mark

redwngr Senior Enthusiast

redwngr

Posted
Posted

Dielectric grease. Jam the pins with it. Pack the flat 4 too, in MI with salt it will turn into green dust if you don't.

 

 

The plugs on the newer trucks seem to be a weak point. Clean and pack with the dielectric grease is a good suggestion no matter where you are located.

 

And wholly crap, do not pull the trailer emergency brake to test it when you are hooked up to the truck. Want to talk about sending the truck into an electrical tissy......

 

 

Mark

 

 

 

You guys do realize that dielectric grease is non-conducting?

jpinoy Enthusiast

jpinoy

Posted
Posted (edited)

 

 

 

 

 

You guys do realize that dielectric grease is non-conducting?

I could be wrong, but I'm thinking they are meaning it for more of a protection of the contacts...

 

Or were you referring to the electrical tissy he talked about? I think that was just in reference to what he did to check the brakes.

 

"pull the trailer emergency brake to test it"

 

Sent from my SM-T810 using Tapatalk

Edited by jpinoy
HeliMark Enthusiast

HeliMark

Posted
Posted

The whole purpose of using dielectric grease is that it is non conductive. This is a simple way of protecting contacts from shorting out due to moisture in an enclosed environment. If the trailer plug on the truck didn't leak, one wouldn't have to do it.

 

The brake test was something completely different.

 

Mark

 

Sent from my SM-G930U using Tapatalk

4x4Pete Enthusiast

4x4Pete

Posted
Posted (edited)

Dielectric grease has long been used for bulb connections even from the factory. Putting some dielectric grease on the trailer or any connection works to prevent corrosion but can get pretty messy. It works on any connection like battery cables too. It doesn't prevent conductivity of the connection (metal to metal) but prevents conductivity between different terminals and also keeps the air away which definitely helps with corrosion. Some greases can conduct electricity and cause a potential short circuit between terminals (like power and ground) without actual metal contact present.

Edited by 4x4Pete
  • Like 1
Offcamber Enthusiast

Offcamber

Posted
Posted

If you use regular grease you run the risk of shorting out everything. Has to be Dielectric.

 

 

 

 

 

 

You guys do realize that dielectric grease is non-conducting?

You ave to use dielectric grease or you will short everything out....As stated keeps moisture out and contacts clean.

  • Like 1
MotionMan Enthusiast

MotionMan

Posted
Posted

Yup, you can spread the grease around and not worry about arcing across terminals. It can get messy but if you don't go overboard you will be OK. It's helps the plug slide easier too so it does not pull the plug out of the bumper....which by the way is a poor design, you have to hold the male end so the female end does not rip it right out of the bumper plastic trim. But it is better than Ford where it is sideways and very close to the receiver pin.

  • 5 years later...
Kmf294 New Member

Kmf294

Posted
Posted
On 4/30/2017 at 10:42 AM, HeliMark said:

The plugs on the newer trucks seem to be a weak point. Clean and pack with the dielectric grease is a good suggestion no matter where you are located.

 

And wholly crap, do not pull the trailer emergency brake to test it when you are hooked up to the truck. Want to talk about sending the truck into an electrical tissy......

 

 

Mark

Any chance you can elaborate on that electrical tissy?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,973
    Total Members
    8,960
    Most Online
    RichardRS
    Newest Member
    RichardRS
    Joined

  • Who's Online   4 Members, 0 Anonymous, 806 Guests (See full list)

  • Latest Articles

  • Posts

    • SwitchBladeSierra
      14-18 Sierra 1500 Heated Steering Wheel Help

      By SwitchBladeSierra · Posted

      Howdy folks,   Recently I pulled a heated steering wheel and clock spring out of a 2015 Sierra All Terrain (part numbers coming soon - will have to disassemble), and just installed it on my 2016 Sierra WT (as base model as it gets).   On install, I noticed that I’m missing the connector often tucked behind the dash for the heating element.     No problem… or so I thought.   I used an “Add-A-Fuse” at my heated steering wheel fuse location, which has voltage, but no wires. I ran it to the positive of the heated steering wheel (Violet/White), and took black to ground.   Hooked up the battery, turned the truck on - no heated steering wheel. No button backlights. Was pleased to see that my cruise control was working though.   Read a post suggesting reversing polarity, so I gave it a shot. Violet and White to ground, Black to power.    Aha! Heat! But I seemingly can’t turn it off AND still no backlights on any of the buttons.    Checked all fuses, everything is still in good order. I’m stumped.   Does anyone have any insight? If so, please share!
    • TrueBlue
      Brake Pad Warning Message

      By TrueBlue · Posted

      I'm about 1800 miles into my last oil change, and yesterday a message appeared saying oil life was at 77%. Not sure why it popped up but I think all of these electronics could be susceptible to solar flares or somesuch. I change my oil right at 3K each time, and that was the first time in 10870 miles that message came up. Strange thing is that it showed on the screen at all since I don't drive with that sort of info displayed on the DIC.
    • SwitchBladeSierra
      Heated steering wheel

      By SwitchBladeSierra · Posted

      I’m praying that someone sees this and can help me out… pulled a heated steering wheel and clock spring out of a 2015 Sierra All Terrain, and just installed it on my 2016 Sierra WT (as base model as it gets).   On install, I noticed that I’m missing the connector often tucked behind the dash.     No problem… or so I thought.   I used an “Add-A-Fuse” at my heated steering wheel fuse location, which has voltage, but no wires. I ran it to the positive of the heated steering wheel (Violet/White), and took black to ground.   Hooked up the battery, turned the truck on - no heated steering wheel. No button backlights. Was pleased to see that my cruise control was working though.   Read a post suggesting reversing polarity, so I gave it a shot. Violet and White to ground, Black to power.    Aha! Heat! But can’t turn it off AND still no backlights.   Checked all fuses, everything is still in good order. I’m stumped.   Does anyone have any insight? If so, please share!  
    • Vu1can
      Brake Pad Warning Message

      By Vu1can · Posted

      Checked the pads today and there's plenty of meat on them. If the message keeps coming up, I'll just answer YES that the pads were replaced and wait for the squeal.
    • richard wysong
      p0449, p0446, p0451 Evap codes

      By richard wysong · Posted

      Welcome to the Forum! Always post the code definitions along with the codes. there are over 18000 possible codes, no one remembers them all and most will skip over your post rather than look them up

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...