Jump to content

trailer brake output

GlenS
 Share

Recommended Posts

GlenS Enthusiast

GlenS

Posted
Posted

So I towed my trailer this morning to a jobsite. I unhooked for a bit had some running around to do. Came back and hooked up. I have no output on trailer brakes. the gauge pops up on dash but no matter what I do I get no level indication. Checked fuses they seem ok. test for voltage i rear at plug with brakes on and no voltage. What am I missing. Trailer brake fuses under hood.///???

 

HeliMark Enthusiast

HeliMark

Posted
Posted

So I towed my trailer this morning to a jobsite. I unhooked for a bit had some running around to do. Came back and hooked up. I have no output on trailer brakes. the gauge pops up on dash but no matter what I do I get no level indication. Checked fuses they seem ok. test for voltage i rear at plug with brakes on and no voltage. What am I missing. Trailer brake fuses under hood.///???

 

Unless the truck senses a trailer is actually hooked up, you will not get any brake voltage at the plug. I have had some issue's and usually cleaning the plug has fixed it. Or in a rush, plugging/unplugging several times works.

 

 

Mark

GlenS Enthusiast

GlenS

Posted
  • Author
Posted

Yes I have lights. I took it apart and cleaned it. Seems to be fine now . Out put is back. Wow it is a sensitive system. I understand what you are saying Mark. Thanks for the help guys.

Offcamber Enthusiast

Offcamber

Posted
Posted

This happened to me on my 1500... Usually just making sure the plug is all the way then you need to shut the truck down and restart. This should rest the system so the truck detects the trailer fully. You can get light and no brakes.

MotionMan Enthusiast

MotionMan

Posted
Posted

Dielectric grease. Jam the pins with it. Pack the flat 4 too, in MI with salt it will turn into green dust if you don't.

SouthpawHD Enthusiast

SouthpawHD

Posted
Posted

GM female plugs are known to have loose connections from time to time. On your trailer plug, pinch the trailer brake plugs closer together using a small pliers and you should be all set.

HeliMark Enthusiast

HeliMark

Posted
Posted

The plugs on the newer trucks seem to be a weak point. Clean and pack with the dielectric grease is a good suggestion no matter where you are located.

 

And wholly crap, do not pull the trailer emergency brake to test it when you are hooked up to the truck. Want to talk about sending the truck into an electrical tissy......

 

 

Mark

redwngr Senior Enthusiast

redwngr

Posted
Posted

Dielectric grease. Jam the pins with it. Pack the flat 4 too, in MI with salt it will turn into green dust if you don't.

 

 

The plugs on the newer trucks seem to be a weak point. Clean and pack with the dielectric grease is a good suggestion no matter where you are located.

 

And wholly crap, do not pull the trailer emergency brake to test it when you are hooked up to the truck. Want to talk about sending the truck into an electrical tissy......

 

 

Mark

 

 

 

You guys do realize that dielectric grease is non-conducting?

jpinoy Enthusiast

jpinoy

Posted
Posted (edited)

 

 

 

 

 

You guys do realize that dielectric grease is non-conducting?

I could be wrong, but I'm thinking they are meaning it for more of a protection of the contacts...

 

Or were you referring to the electrical tissy he talked about? I think that was just in reference to what he did to check the brakes.

 

"pull the trailer emergency brake to test it"

 

Sent from my SM-T810 using Tapatalk

Edited by jpinoy
HeliMark Enthusiast

HeliMark

Posted
Posted

The whole purpose of using dielectric grease is that it is non conductive. This is a simple way of protecting contacts from shorting out due to moisture in an enclosed environment. If the trailer plug on the truck didn't leak, one wouldn't have to do it.

 

The brake test was something completely different.

 

Mark

 

Sent from my SM-G930U using Tapatalk

4x4Pete Enthusiast

4x4Pete

Posted
Posted (edited)

Dielectric grease has long been used for bulb connections even from the factory. Putting some dielectric grease on the trailer or any connection works to prevent corrosion but can get pretty messy. It works on any connection like battery cables too. It doesn't prevent conductivity of the connection (metal to metal) but prevents conductivity between different terminals and also keeps the air away which definitely helps with corrosion. Some greases can conduct electricity and cause a potential short circuit between terminals (like power and ground) without actual metal contact present.

Edited by 4x4Pete
  • Like 1
Offcamber Enthusiast

Offcamber

Posted
Posted

If you use regular grease you run the risk of shorting out everything. Has to be Dielectric.

 

 

 

 

 

 

You guys do realize that dielectric grease is non-conducting?

You ave to use dielectric grease or you will short everything out....As stated keeps moisture out and contacts clean.

  • Like 1
MotionMan Enthusiast

MotionMan

Posted
Posted

Yup, you can spread the grease around and not worry about arcing across terminals. It can get messy but if you don't go overboard you will be OK. It's helps the plug slide easier too so it does not pull the plug out of the bumper....which by the way is a poor design, you have to hold the male end so the female end does not rip it right out of the bumper plastic trim. But it is better than Ford where it is sideways and very close to the receiver pin.

  • 5 years later...
Kmf294 New Member

Kmf294

Posted
Posted
On 4/30/2017 at 10:42 AM, HeliMark said:

The plugs on the newer trucks seem to be a weak point. Clean and pack with the dielectric grease is a good suggestion no matter where you are located.

 

And wholly crap, do not pull the trailer emergency brake to test it when you are hooked up to the truck. Want to talk about sending the truck into an electrical tissy......

 

 

Mark

Any chance you can elaborate on that electrical tissy?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      Software Update

      By Chuck FB · Posted

      I am not techy at all but wondered if you have the truck running but sitting still in park as some functions gray out as soon as the truck is moving. I believe in the settings for updates you can choose for it NOT to update and I wonder by chance if maybe that was chosen before and now it won't allow you to chose to press update, I think that is back in the settings menu where it has all the items one wants on or off etc. Also I assume you have a wifi connection and checked that it has some signal strength, not that it would have anything to do with the grayed out updates choice in that case. What I am thinking out loud of here may be be of no value but thought I would suggest it, sometimes it can be the simplest thing that resolves an issue.  
    • Chuck FB
      Dave's Auto (custom engine builder) tear down of L8T

      By Chuck FB · Posted

      The so called rare failure that some certainly liked to tout ( die hard Ford fan boys ) as per the lifter failing and wiping out the cam. Back when it started happening the blame was being pointed to the lifters and honestly I never did hear anything myself conclusively one way or the other on that. Ford themselves in I believe 2024 had a technical bulletin I will call it that came out and for some engine platforms they were reprograming the engines idle speed but also they had a software update for the oil pump which then some time later was said what that software update did as to be increasing the oil pressure at idle. It is a good question if that issue was completely solved as one Ford specialist mechanic youtuber said he saw failures after that time period. Like anything there would be the variables, what oil is being used and the OCI and how much idle time gets put on an engine. I've seen some comments to claim that the L8T isn't so happy with high idle time either but I also know that companies that require their vehicle to idle a lot on the job don't tend to get the oil changed often enough for all those hours of idle time and go off of the odometer. 
    • bwiese
      Lower trims ( WT, Custom, Silverado ( aka LT )

      By bwiese · Posted

      My 2026 Silv. 1500 WT (reg cab/short bed/4wd) has the 40/20/40 with storage in lower middle seat as well as the fold-down center bolster/armrest.   With the dual glove boxes this is about as much storage as possible in a std cab IMHO. Bill
    • bwiese
      2026 Silv. 1500 WT reg cab: how many speakers do I have? Is amp module separate?

      By bwiese · Posted

      I have a 2026 base 1500 "WT" regular cab with basic Chevy "Infotainment 3" 7-inch screen/radio. How many speakers do I have If I want to upgrade? Is the audio amp separate from the radio/display unit]? [I listen to classical and it gets a bit raspy at slightly higher volumes. Don't need a sub etc.] Do I have two or 1 speakers in the doors? etc. Thanks Bill  San Jose
    • davester
      Bench seat swap for 2021-2024 suburban

      By davester · Posted

      probably won't get a response from that user, as they haven't returned to the site since making that one post.  users don't (at least I don't, and I haven't seen any setting which would notify me via say, email) get any notification other than going to this site, and checking if they got a response on their thread...

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...