Jump to content

Recovery hook

Shooter1
 Share

Recommended Posts

Shooter1 New Member

Shooter1

Posted
Posted

Trying to swap out the black hooks to chrome on my 2017 silverado 1500. Passenger side easy but the front bolt on the drivers side hits a bumper bracket. If it had been installed the other direction it would be no problem. Do you have to cut it out or is there another trick? Have seen the videos for 2014 and 15 models but 2017 is different.

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

JimCost2014
JimCost2014

Yes, cut the bolt. If you bought the hooks from GM they come with new hardware, so no point in trying to save the old bolt by tearing off/moving things that don't need to be touched. Above poster with

No Tyme
No Tyme

NO, you do NOT have to cut the bolt. I did this last month, with the help of a you tube video on installing a bull bar a guy showed 3 extra bolts that you undo and pry up on the top piece where the he

mike67naz
mike67naz

2014-2015 correct. Changed on 2016 and up. I know, just checked this weekend, my 2016 Sierra does not have the same exposed bolts to undue.

Posted Images

MS3DALE Senior Enthusiast

MS3DALE

Posted
Posted

Cut it......

 

Tow Hook Replacement (2016 and Beyond) Chevy and GMC Crew Cab With Existing Tow Hooks Removal
  1. Raise and support vehicle.
  2. Driver Tow Hook
    1. Loosen tow hook through bolt and remove bolt out of frame rail enough to allow clearance for bolt head to be cut (qty 1).
    2. Cut bolt head off and remove bolt out of the outboard side of frame rail.
    3. Remove the rear tow hook bolt and remove the OE tow hook (qty 1).
  3. Passenger Side Tow Hook
    1. Remove tow hook bolts (qty 2)/nut (qty 1).
    2. Note: Passenger side tow hook bolts should not need to be cut.
  4. Swap rubber guard/seal from OE tow hooks to replacement tow hooks.
Installation

Caution: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  1. Install new tow hooks (4) to frame rail (nut-qty 1 and bolt-qty 2 per hook) making sure that the through bolt head is facing outboard of the frame rail.
  2. Install the through bolt (3) and nut (2) and tighten to 80 N.m (59 lb ft).
  3. Install the short bolt (1) to frame and tighten to 80 N.m (59 lb ft).
  4. Lower vehicle.
Boardmember Senior Enthusiast

Boardmember

Posted
Posted (edited)

I have a 2wd that does not have tow/recovery hooks. Should I purchase a set, I assume the install would be as indicated above but to include careful trim out of the below-bumper moulding. Is that correct?

 

If so, should be pretty simple.

 

Nice documentation. Thanks.

Edited by Boardmember
MS3DALE Senior Enthusiast

MS3DALE

Posted
Posted (edited)

I have a 2wd that does not have tow/recovery hooks. Should I purchase a set, I assume the install would be as indicated above but to include careful trim out of the below-bumper moulding. Is that correct?

 

If so, should be pretty simple.

 

Nice documentation. Thanks.

 

Looks like there are tow hook delete covers on your GMC that must be changed out.....

 

Tow Hook Installation GMC (2014 thru 2018)

    2. Remove the LH/RH bumper bracket fasteners, (qty 16) and brackets. Upon Reassembly tighten fasteners to 58 N.m (43 lb ft).

      Disconnect fog lamp connector.

    4. Remove tow hook delete cover fasteners (qty 8).
    5. Remove tow hook delete covers.
  3. Install front tow hook covers, P/N 23243484 and 23243485 using retained hardware.

    Tighten

    Tighten to 6 N.m (53 lb in).

Edited by MS3DALE
Boardmember Senior Enthusiast

Boardmember

Posted
Posted

Thank you!

 

Holy cow. This DOES NOT have my name (or wallet) written on it.

 

If done by a local body shop, what's an anticipated labor cost? I see chrome hooks on eBay in the $130-150 range.

2017_whitez71 Enthusiast

2017_whitez71

Posted
Posted

I just installed red tow hooks on my 2017 z71 silverado. I used a sawzall to cut the head off the head of the bolt off on the driver side. Slide the bolt out until it touched the bracket and held the head with a pair of vise grips and cut the bolt. Was a piece of cake.

SilveradoSaver Senior Enthusiast

SilveradoSaver

Posted
Posted

Thank you!

 

Holy cow. This DOES NOT have my name (or wallet) written on it.

 

If done by a local body shop, what's an anticipated labor cost? I see chrome hooks on eBay in the $130-150 range.

 

 

I'd guess they'd charge you an hours labour, so depends what the going rate is in your area.

No Tyme Senior Enthusiast

No Tyme

Posted
Posted

NO, you do NOT have to cut the bolt. I did this last month, with the help of a you tube video on installing a bull bar a guy showed 3 extra bolts that you undo and pry up on the top piece where the head of the bolt is. It is a bit of a job like the bolt on the passenger side but I did it without cutting and I am on social security.

  • Like 1
Chevytrk1 Enthusiast

Chevytrk1

Posted
Posted

Thanks for the write up and info. I might consider doing one myself too.

Anyone have any pictures of a chrome hook installed?

JimCost2014 Senior Enthusiast

JimCost2014

Posted
Posted (edited)

Trying to swap out the black hooks to chrome on my 2017 silverado 1500. Passenger side easy but the front bolt on the drivers side hits a bumper bracket. If it had been installed the other direction it would be no problem. Do you have to cut it out or is there another trick? Have seen the videos for 2014 and 15 models but 2017 is different.

Yes, cut the bolt. If you bought the hooks from GM they come with new hardware, so no point in trying to save the old bolt by tearing off/moving things that don't need to be touched. Above poster with the sawzall is the best idea, exactly what i did.

Edited by jimcost2014
  • Like 2
mike67naz Enthusiast

mike67naz

Posted
Posted

NO, you do NOT have to cut the bolt. I did this last month, with the help of a you tube video on installing a bull bar a guy showed 3 extra bolts that you undo and pry up on the top piece where the head of the bolt is. It is a bit of a job like the bolt on the passenger side but I did it without cutting and I am on social security.

2014-2015 correct. Changed on 2016 and up. I know, just checked this weekend, my 2016 Sierra does not have the same exposed bolts to undue.

  • Like 1
No Tyme Senior Enthusiast

No Tyme

Posted
Posted

2014-2015 correct. Changed on 2016 and up. I know, just checked this weekend, my 2016 Sierra does not have the same exposed bolts to undue.

Thank you for sharing that info. I watched a video on a bull bar install and since I did not get extra bolts with mine I had to salvage the originals.

Good to know that there is a difference between 14/15's and the 16's. :thumbs:

Boardmember Senior Enthusiast

Boardmember

Posted
Posted (edited)

So my '16 2wd would be less of a hassle? How so? I'd like to add...

Edited by Boardmember
MidKNIGHTZ71 Enthusiast

MidKNIGHTZ71

Posted
Posted

I bought a rotary tool from home depot and cut them. Took me 5 minutes to remove the hooks. Then I took a razor blade and trimmed the openings for the bull bar to fit.

 

Removing the grill and bumper is unnecessary.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Missing thrust bearing? And oil selection

      By Atlas · Posted

      No doubt... But, as someone who doesn't pay for his services, but who has provided a few views/clicks on his Youtube platform, the data around the Mobil oil testing I think does have some value including to "freeloaders" like me.   A lot of what he's doing is likely showing the OE's work in their oil selection, something that many of us had kind of assumed was true all along, a good balance of both excellent protection and efficiency.
    • Z45
      Missing thrust bearing? And oil selection

      By Z45 · Posted

      Lake Speed is drumming up business for his company just by being in the spot-light so he has a vested interest in stoking the 0W-20 fire.  IMO  
    • Chuck FB
      summer road trips in the 2026 2500HD

      By Chuck FB · Posted

      I knew when I bought my truck that it had off road hill decent or craw control or whatever they call it and rolled my eyes at that but it gets throw on with other options my truck has, I just never had a heads up if the highway speed regular cruise setting had anything to do with the brakes and that took me by surprise. If you've ever been to the top of Pikes Peak and watched those ahead of you on the way down with their brake lights on constantly, one can guess they are probably not gearing down or not enough anyway if their vehicle will allow and a good reason their is a brake check spot part way down where they use an infra red heat gun to check how hot ones brakes are front and rear.    Your right that once one gets out of the front range by Denver and I've not been on that stretch of 285 between Denver and Fairplay myself but I know its high and Fairplay at 10000 feet, Buena Vista at 8000, it drops a bit from there but then your going back up and over the 11000 pass and Durango is at 6500 . So yes your definitely right that 6500 and a lot higher is the theme of going anywhere out in that direction from Denver but hey, the down hill sections give fantastic fuel mileage !.    I don't even look at the fuel pumps for what premium costs here, since I live on a farm and up to this point get fuel delivered I am rarely in front of a fuel pump and when I am, I am often using card lock bulk fuel stations so it tells me what the price is AFTER I buy the fuel. Looking up on gas buddy and converting to US gallons but in Canadian dollars, regular on average of the prices listed was around 5.95 and premium is around 7.00 . That was one reason I did not go for the 6.2 half ton aside from its lack of carrying/towing if one was going by the rule of using premium fuel and until recently one could only buy regular farm gas if playing the few cents off game for farm dyed fuel for a "farm licensed pickup". But yes I hear you on the fuel price difference and like the diesel theme with it often being more expensive then gas it doesn't have quite the charm to it either as it once did although right now here for some reason the price of diesel has come down more so its now inline with the price of regular gas. 
    • KARNUT
      Missing thrust bearing? And oil selection

      By KARNUT · Posted

      I agree with this assessment. As you know I’m testing longevity with vehicles for the first time. I have a few vehicles I passed to kids and grandkids. We’re all past 100K miles some approaching 170K. I’m the only one doing 5k oil changes. The rest whatever the minder says. I’m the only one doing frequent transmission service. My odyssey the trip vehicle at 200K will be finished as a trip vehicle. I recently changed to high mileage oil, Valvoline. I can’t get past the fact that all manufacturers want to claim long service life. I just don’t make sense that they would go with low weight oil for mileage. While sacrificing longevity.
    • Atlas
      Missing thrust bearing? And oil selection

      By Atlas · Posted

      There's absolutely a mountain of profit in catering to the "I do my own research" crowd, people who are certain they know better. And I don't mean there isn't data to support that 0w40 produces less wear product than 0w20 in an engine like the 3.0 Duramax, that only feeds them the assurance they need. Again, my whole thing with oil selection is, sure, 0w40 or 0w30 produces less wear product. Are we talking the difference between the engine lasting only 100k versus 200k? Or are we talking more like, if the engine will already go 350k on a good 0w20 regimen recommended by the OE, is using 0w40 going to get us to 355k, assuming we can even get the rest of the truck to last that long, meanwhile sacrificing the first 5y, 100k in powertrain warranty. The answer isn't easy, there are tradeoffs.   I willfully use 0w20 Dexos D for this reason, knowing that a 0w40 will produce slightly less wear. I don't believe the delta in wear product is meaningful over the lifetime of the engine, and I place much more importance on driving style and overall feeding and care of the engine as a whole. It's the mentality that someone can abstain from alcohol their whole life which is an amazing boost to health by itself, theoretically. But if they're sedentary, that lifestyle choice will most likely kill them young despite their other, concerted efforts. Maybe someone doesn't drink AND they are the perfect picture of health and activity AND they use 0w40 AND they treat their engine perfectly. If living until 130 years is the goal, sure, do that. But it's going to be a really old truck falling apart around a good engine for that last 30 years, without a doubt.   I watched Demonworks' other video on the 100k+ 3.0 Duramax that had dealer 0w20 changes on what appears to be OLM-prescribed intervals (8-10k).   The QR codes are still present and readable on the main bearings. That's how little wear it has.   That's not proof that anyone else should stick to 0w20, but it's confirmation, for me, that 0w20 is perfectly acceptable to use in these engines.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...