Jump to content

Rough Country 3.5 Knuckle Lift Kit

Instructor31

By Instructor31
in Modifications & Accessories

 Share

Recommended Posts

Instructor31 Enthusiast

Instructor31

Posted
Posted (edited)

Good evening,

 

Here’s my 2 cents on the Rough Country 3.5 Knuckle Lift Kit on my 2017 Silverado 1500 Z71. I’ve been driving on it for the past 20k miles and haven’t had an issue. The ride quality is nice, nothing out of the ordinary. I did not option to change the front shocks , just the rear ones. 

 

The lift kit was very easy to install. Key things to watch out for are the front differential drop spacers, they are the most difficult thing to get in place. Also, I’ve seen on other forums that people have been leaving the front diff cooling fins in “thinking” that it won’t need to get cut because it “doesn’t make contact with the cross member.” Yeah.. BS, I thought the same but the cooling find do actually touch the cross member, so make sure to cut them off to avoid miss alignment of your CV axel with your front diff.

 

Rear blocks and shocks are straight forward, make sure you place the blocks on the correct way with the taper or “ skinny “ end to the front. Measure them out to find that smaller side. 

If not you will get shaking while you break at about 25mph and under due to the drive shaft and rear diff universal joints not being at the required angles.

 

the kit does require a 1/4” spacer for stock wheel, get it, if not you will be rubbing on your upper control arm. 

 

The included Knuckle addresses the upper control arm and CV axel angles. They’re not at an extreme angle, they look like stock angles if not damn near it. I have disassembled my whole suspension again to check the ware on the ball joints and they are still looking good and do not hear any popping sounds from the suspension, or abywhere else for that matter.

 

If you’re looking at getting your truck lifted and don’t want to break the bank and get some ground clearance, I think this is a very nice option.

https://imgur.com/gallery/5O8DW1V

 

 

Edited by Instructor31
  • Like 2
  • Thanks 1
Tleesmith14 Enthusiast

Tleesmith14

Posted
Posted

Looks good and this is a kit I am very interested in getting..what size tire did you go with? Did the 1/4 spacer keep all 4 tires in the same track or do the fronts stuck way out like you see with alot of the chevys? You say ride quality nothing out of the ordinary how does it compare to stock?  Does your truck sag much when towing?  

 

Instructor31 Enthusiast

Instructor31

Posted
  • Author
Posted
47 minutes ago, Tleesmith14 said:

Looks good and this is a kit I am very interested in getting..what size tire did you go with? Did the 1/4 spacer keep all 4 tires in the same track or do the fronts stuck way out like you see with alot of the chevys? You say ride quality nothing out of the ordinary how does it compare to stock?  Does your truck sag much when towing?  

 

I went with a 285/60/20R. The 1/4 spacer was mostly for clearance since I kept stock wheels. Track is still stock looking, even with the “oversized” tires, I’m still flush with the fenders. It’s been a while since stock but if it means anything, it’s still as smooth, it’s not too rough or stiff. A little depending on load. I chose this kit because I still tow and didn’t want to lose all functionality (torque for the most part).

 

  • 1 month later...
virtualron1976 New Member

virtualron1976

Posted
Posted

I just had this 3.5” knuckle kit put on as well. Rides good, looks awesome. 

 

One issue im researching is if anyone who did this has noticed increased noise or front diff activation when driving in “auto.” The shop that did my install said they are checking with RC engineers, but I haven’t heard back yet. Any thoughts if you have this kit? 

3FA3B126-1205-4375-ADB3-10C269666CCE.jpeg

  • Like 1
  • Thanks 1
  • 1 month later...
TimHortonsJunky Enthusiast

TimHortonsJunky

Posted
Posted
On 2019-01-29 at 10:36 PM, virtualron1976 said:

I just had this 3.5” knuckle kit put on as well. Rides good, looks awesome. 

 

One issue im researching is if anyone who did this has noticed increased noise or front diff activation when driving in “auto.” The shop that did my install said they are checking with RC engineers, but I haven’t heard back yet. Any thoughts if you have this kit? 

3FA3B126-1205-4375-ADB3-10C269666CCE.jpeg

any updates on how these lifts are performing?

  • 1 year later...
2014gmc1500withlift New Member

2014gmc1500withlift

Posted
Posted

So i installed the rough country 3.5" suspension lift on my 2014 GMC 1500. there really haven't been any problems with it except for one thing. It doesn't happen every time i turn but every once in awhile when i turn my wheel sharply it makes a real small popping sound from my front left wheel. its always the front left wheel and only happens when i turn the same way.

 

so in short, i turn the wheel sharply to the right and a quiet popping sound comes. not every time. just randomly.

if anyone can help me out that'd be extremely appreciated!!

WilliamBos Senior Enthusiast

WilliamBos

Posted
Posted
On 1/29/2019 at 9:36 PM, virtualron1976 said:

I just had this 3.5” knuckle kit put on as well. Rides good, looks awesome. 

 

One issue im researching is if anyone who did this has noticed increased noise or front diff activation when driving in “auto.” The shop that did my install said they are checking with RC engineers, but I haven’t heard back yet. Any thoughts if you have this kit? 

3FA3B126-1205-4375-ADB3-10C269666CCE.jpeg

Any updates?  I have auto 4x4 too?

NWdirt Enthusiast

NWdirt

Posted
Posted

I have about 15k miles on 3.5" RC knuckle lift. It's been flawless, even after 13 passes at the drag strip. I would say it ride about the same maybe be a little stiffer. I did change RC rear 3" blocks that was in the kit to 2" blocks to make my 2014 LTZ 6.2l level. Just ordered 5100 Bilsteins.

20200215_223554.jpg

Connor Bain New Member

Connor Bain

Posted
Posted
On 4/7/2020 at 11:36 AM, NWdirt said:

I have about 15k miles on 3.5" RC knuckle lift. It's been flawless, even after 13 passes at the drag strip. I would say it ride about the same maybe be a little stiffer. I did change RC rear 3" blocks that was in the kit to 2" blocks to make my 2014 LTZ 6.2l level. Just ordered 5100 Bilsteins.

20200215_223554.jpg

wow!! that is a really nice truck!.

 

I have a 2018 Sierra 1500 and really thinking about getting this kit, but all i hear is how trash angles are. reading all this really is making my decision easier to purchase the kit!

Connor Bain New Member

Connor Bain

Posted
Posted
On 4/7/2020 at 11:36 AM, NWdirt said:

I have about 15k miles on 3.5" RC knuckle lift. It's been flawless, even after 13 passes at the drag strip. I would say it ride about the same maybe be a little stiffer. I did change RC rear 3" blocks that was in the kit to 2" blocks to make my 2014 LTZ 6.2l level. Just ordered 5100 Bilsteins.

20200215_223554.jpg

do you have instagram by chance, so i can check out more photos!?

NWdirt Enthusiast

NWdirt

Posted
Posted
5 hours ago, Connor Bain said:

do you have instagram by chance, so i can check out more photos!?

Sorry, I don't. Here's a few more pictures.20200412_164831.thumb.jpg.79023f00f8215291f3d80ae5ccc0a055.jpg

  • 11 months later...
Mixon87 New Member

Mixon87

Posted
Posted (edited)

So I installed on my 2017 Silverado and have the same popping sound from my front drivers side. Has anyone figured out or know why? Also with the three inch block in back I’m not level is still 1 1/2 higher from back to front?

Edited by Mixon87
YukonXL04 Enthusiast

YukonXL04

Posted
Posted

I have it on my 18, I have no noises. I do feel stiffer than before steering when in 4x4, but I feel some of that is the new tires not slipping as much.

I am about 1.25" higher in the rear. I prefer it as I tow stuff often. And visually it's hard to tell it's not level

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • newdude
      2027 GMC Sierra: Official Discussion

      By newdude · Posted

      It was never mandated.  Ever.    Automakers were incentivized to install it by getting CAFE credits to help with their vehicle fleet fuel economy scores.  They were being handed money/CAFE credits to install it.  Which is NOT a mandate.       The current admin removed the incentives that were behind them installing it.       
    • lanaderay
      5 Best Slide Down Gameplay Tips! 

      By lanaderay · Posted

      Are you playing Slide Down endlessly but your score is still low? Are you constantly crashing into obstacles as the game speed increases? Don't worry, this article will share 5 invaluable tips to help you master the race and impress your friends. Golden Rules 1. Look one step further. The mistake of 90% of new players is only staring at their character. The secret of experts is to look towards the top of the screen (where the slide is about to appear). This gives your brain an extra 0.5 - 1 second to process the situation and determine the direction of movement before the obstacle approaches. 2. Use gentle movements; don't swipe too hard. Slide Down is very sensitive. Moving your finger too forcefully or with excessive amplitude will cause your character to be thrown off course or crash into a wall. Practise moving your finger with small, decisive, and precise movements. 3. Don't be greedy for gold in dangerous locations. Gold coins are tempting for buying skins, but life is more important. If you see a gold coin right on the edge of a cliff or next to a spike trap, ignore it. Our goal is a High Score, and your score only increases if you survive. 4. Make the most of Power-ups. During the slide, you'll encounter items like Magnets (attract gold) or Shields (temporary invincibility). Never miss them! Especially the Shield, it's your "get out of jail free card" to help you get through those deadly fast sections. 5. Stay calm when speed peaks. When your score exceeds 500 or 1000, the game speed will be very fast. At this point, don't try to think logically; let your natural reflexes work. Take deep breaths and don't panic. Apply these 5 tips to your next game, and your leaderboard will surely improve dramatically. Good luck climbing the Slide Down leaderboard!
    • lingyuair
      Why I Recommend a Desiccant Air Dryer for Cleaner, Drier Compressed Air

      By lingyuair · Posted

      If you use compressed air regularly, one problem you cannot ignore is moisture. Water in the air line can cause rust, unstable air pressure, poor tool performance, and even damage to sensitive equipment. That is why I highly recommend using a desiccant air dryer. A desiccant air dryer is designed to remove moisture from compressed air by using drying materials such as activated alumina or molecular sieve. Compared with basic water separators, it can achieve much lower dew points, making it especially useful for applications that require dry and stable air. For workshops, painting systems, pneumatic tools, CNC machines, laser cutting equipment, and industrial production lines, a desiccant air dryer can make a big difference. It helps protect equipment, improve air quality, reduce maintenance costs, and extend the service life of the whole compressed air system. Another advantage is reliability. Many desiccant air dryers are built for continuous operation and can maintain stable drying performance even in demanding environments. For users who care about long-term efficiency and equipment protection, this is a smart investment. When choosing a desiccant air dryer, I suggest paying attention to air flow capacity, working pressure, dew point performance, regeneration method, and maintenance requirements. A good model should match your compressor system and actual air consumption. Overall, if moisture is causing problems in your compressed air system, a desiccant air dryer is definitely worth considering. It is practical, efficient, and highly useful for anyone who needs clean, dry, and reliable compressed air.
    • Jsdirt
      2027 GMC Sierra: Official Discussion

      By Jsdirt · Posted

      My brand new 2007 Silverado's wax frame was rust from end to end partway through it's SECOND winter here in MA. That stuff is completely useless.    
    • Jsdirt
      2027 GMC Sierra: Official Discussion

      By Jsdirt · Posted

      I went another direction after losing a trailer tire, thanks to not being able to access air at ANY of the 5 gas stations and garages I stopped at prior, with a Toyota Tacoma onboard, 50 miles from the Canadian border. They were either out of order, access was blocked, or the hose a few feet too short and I couldn't get any closer without risking damage to someone's property.   https://postimg.cc/gallery/X5QJ55w

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...