Jump to content

Headlight Adjustment - Proper

Taz56
 Share

Recommended Posts

Taz56 Enthusiast

Taz56

Posted
Posted

I am curious on headlight adjustment if anyone knows. 

 

I am curious on headlight adjustment.

I own a 2019 GMC Sierra AT4. I Googled how to determine headlight height. I found this:

Park against a wall on a flat surface. Mark with tape or chalk the horizontal and vertical points of the headlights on the wall.

Back up 25 feet and adjust (if needed) so at 25 feet away they point in the same spot.

 

However in my case I do not feel this is any longer relevant as I have put bigger tires on and done a front end level kit. So my stance against a wall is no longer “factory”.  

Is there a "height" and “width” that I should aim for, Google is not being very helpful with that.

AD80 Enthusiast

AD80

Posted
Posted (edited)

Their should be a small dot or indentation on the front of your headlights  , marking the center. Measure from that dot to the ground.  Back up 25 away from the wall.  Your  light cut off point should be about 2" lower than your first measurement.  So if your headlights are 47" from the ground, the top of the cut off line should be 45" on the wall when 25 feet away.    I dont know if this is the official way to do it, but this is seems to be the way folks are doing it, and it should get you in the ballpark.   

Edited by AD80
  • Like 1
Taz56 Enthusiast

Taz56

Posted
  • Author
Posted
27 minutes ago, AD80 said:

Their should be a small dot or indentation on the front of your headlights  , marking the center. Measure from that dot to the ground.  Back up 25 away from the wall.  Your  light cut off point should be about 2" lower than your first measurement.  So if your headlights are 47" from the ground, the top of the cut off line should be 45" on the wall when 25 feet away.    I dont know if this is the official way to do it, but this is seems to be the way folks are doing it, and it should get you in the ballpark.   

Sounds the same as what I posted. I assume the 2" you are referring to is to make up for the tires and leveling kit? 

aseibel Senior Enthusiast

aseibel

Posted
Posted (edited)

No, the 2" inches means your lights should be aimed slightly downhill. So 2" over 25' is only about 1/3 of a degree below horizontal. That should keep your low beams from blinding oncoming drivers.

 

your "instructions" are for people who don't own a tape measure apparently. You don't even need a wall. If you park in a flat area, measure the centerline of the bulb, then stand 25' away and measure the cutoff line again, it should be 2" less than the light bulb center.

Edited by aseibel
Taz56 Enthusiast

Taz56

Posted
  • Author
Posted (edited)
4 minutes ago, aseibel said:

No, the 2" inches means your lights should be aimed slightly downhill. So 2" over 25' is only about 1/3 of a degree below horizontal. That should keep your low beams from blinding oncoming drivers.

I get that, but what I was asking is, do I go "more than 2"" because I lifted my trucks front end and I put on bigger tires?

 

When I bought the truck lets say (for example only) that I was at 43" for the headlight, when I installed bigger tires and leveled the front end I am now at 49" Going down 2" brings me to 47" which is still higher than I was stock and I am still blinding people.

 

The point of this post was to ask what it should be at as I did not think to measure before I lifted the front end and put on bigger tires.

Edited by Taz56
aseibel Senior Enthusiast

aseibel

Posted
Posted
Just now, Taz56 said:

I get that, but what I was asking is, do I go "more than 2"" because I lifted my trucks front end and I put on bigger tires?

 

When I bought the truck lets say (for example only) that I was at 43" for the headlight, when I installed bigger tires and leveled the front end I am now at 52" Going down 2" brings me to 50" which is still higher than I was stock and I am still blinding people.

 

The point of this post was to ask what it should be at as I did not think to measure before I lifted the front end and put on bigger tires.

It doesn't matter what the old height was. As long as your lights are pointed downhill NOW, they shouldn't blind people unless you are tailgating them or parked directly behind at a stoplight/mcdonalds drive through.

 

forget about the "before" and just measure at the new light C/L and at 25' away. that's all that matters.

Taz56 Enthusiast

Taz56

Posted
  • Author
Posted
Just now, aseibel said:

It doesn't matter what the old height was. As long as your lights are pointed downhill NOW, they shouldn't blind people unless you are tailgating them or parked directly behind at a stoplight/mcdonalds drive through.

 

forget about the "before" and just measure at the new light C/L and at 25' away. that's all that matters.

OK. Will do.

mafd2 Senior Enthusiast

mafd2

Posted
Posted

I can tell where the cut off point on the road should be on dim. I've set many sets and projector lights as well on lowered and leveled trucks.  I use a level slab and a brick wall to level the left and right headlights the same using the bricks or mortar joints.  Aim is perfect and I never get flashed.

redwngr Senior Enthusiast

redwngr

Posted
Posted

Whatever measure/adjustment method is selected, the verification is still how other vehicles respond.

 

Frequently getting flashed on level roads means they are to high. 

A head-on because a blinded driver that drifts into your lane can make for a bad evening. 

 

 

  • 9 months later...
JansterZ71 Enthusiast

JansterZ71

Posted
Posted
On 2/5/2020 at 9:26 AM, Taz56 said:

I am curious on headlight adjustment if anyone knows. 

 

I am curious on headlight adjustment.

I own a 2019 GMC Sierra AT4. I Googled how to determine headlight height. I found this:

Park against a wall on a flat surface. Mark with tape or chalk the horizontal and vertical points of the headlights on the wall.

Back up 25 feet and adjust (if needed) so at 25 feet away they point in the same spot.

 

However in my case I do not feel this is any longer relevant as I have put bigger tires on and done a front end level kit. So my stance against a wall is no longer “factory”.  

Is there a "height" and “width” that I should aim for, Google is not being very helpful with that.

Did you end up adjusting?

Taz56 Enthusiast

Taz56

Posted
  • Author
Posted
13 hours ago, JansterZ71 said:

Did you end up adjusting?

No. I meant to and kept forgetting.... I still want to LOL

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • asilverblazer
      Intermittent no-code issues on 2022.5+ V8 trucks — what did the shop fail to capture?

      By asilverblazer · Posted

      Length/amount of data capture will be important to consider, sifting through 5 minutes of a data log can be enormous when it is stored in milliseconds. Being able to find the 'event' let alone decipher it.   Presumably the driver would notice something and hit a button to capture the 'window' of data. That window has to be large enough for the operator to recognize the event and react accordingly.    The data has to be able to be retrieved easily.   The data has to be able to be understood. Which is the biggest challenge, dealer techs won't even know what most of it is and would likely not even look at it if an owner brought it to them. Meaning the owner, the least educated/qualified, trying to understand it.    How will the data be presented? Could specific PIDs be selected and a timelapse graph be watched? How will a specific value be noted as abnormal? Additionally, a good data logger would be able to 'learn' normal values for a specific vehicle and flag abnormalities automatically. It could in theory watch parameters degrade over time and suggest maintenance as needed. (If the MAF reading begins tapering off for a given set of other readings - MAP, throttle position, Ambient, etc.. a flag to check air filter.) With the amount of data available, a device (really the vehicle rather than an additional accessory) should be able to do more than issue a DTC. It should be able to run the full diagnostic suite automatically and present a solution rather than a code. (It's not the 90's anymore). The technology is available for the vehicle to not just say "P0087", it should know low fuel pressure, check other PIDs to narrow down the problem itself, and determine if it is a lift pump, high pressure pump, regulator, leak in the fuel line, clogged filter, etc. Even if it can't narrow it down, it should be able to guide the user to the likely problems.   This would be a major problem for dealer service departments, which are the manufacturers customers it is in their collective best interest to NOT have this available to the consumer.   Further, if the owner is going to be the primary consumer of the data, it's got to be at a consumer price point vs. dealer only specialty tool price.   This group is more 'involved' in their vehicle than general public/consumer and will have knowledge, experience, needs and desires that are quite different from the market at large.   
    • KARNUT
      OCI, not when but why?

      By KARNUT · Posted

      I put the prof up. If you read what I posted. You can see that housing, cars and income are in line with the era we were talking about. It’s harder in some places easier in others. Let’s agree to disagree and put this back on track, OK? We both are pretty stubborn and hard headed. But I bring receipts. If you wish I will not respond to you in the future. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      Lets see if I can sum up two pages of nothing useful.    You want to refute your own governments data of the "Purchasing Power" Index FOR THE ENTIRE USA and its territories replacing it with the experience of a single family and its business and label that reality?  Then pound on that for a week hoping it will find traction?    Stan, I've told you several times. I don't do irrational. There are more people in the USA than your family.    I'm pretty sure this tread is so blown up. I'll give you a few days or months if need be to post yourself silent then I'll see if I can find enough parts of the train to reassemble it. 
    • asilverblazer
      VSE CCV Bypass - Anyone have this installed in their L5P?

      By asilverblazer · Posted

      Facebook groups hate VSE, poor customer service; their responses to criticisms are pretty poor for a reputable company. I'm not a customer, haven't bought anything from them, but how they handle themselves on social media is a definite "No" for me. 
    • asilverblazer
      Transmission Woes :-(

      By asilverblazer · Posted

      $10,000 for a transmission?   Pretty sure I could buy all the parts, tools, and education to rebuild it myself for a quarter of that amount.   or swap it out with a new one...

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...