Jump to content

Power locking tailgate

John Fleming
 Share

Recommended Posts

John Fleming Enthusiast

John Fleming

Posted
Posted (edited)

Anybody know if it would be possible to add a power lock to the tailgate to work with the door locks and key fob? What all would it entail, an actuator and bcm programming I would assume?

Thanks

Edited by John Fleming
walshie Enthusiast

walshie

Posted
Posted

Pop a lock. Taps into door wiring
No programming needed.

Sent from my SM-G960U using Tapatalk

John Fleming Enthusiast

John Fleming

Posted
  • Author
Posted
On 6/3/2020 at 6:13 PM, Cwildman said:

Does anyone have the part number for the tailgate power lock?

Sent from my Pixel 2 XL using Tapatalk
 

This is what I found for a 16 on rockauto

Screenshot_20200605-151340.png

  • 2 weeks later...
NoLand Enthusiast

NoLand

Posted
Posted
This is what I found for a 16 on rockauto
Screenshot_20200605-151340.thumb.png.f54853a9d67b9dcafc60d07f2ac0692c.png

So did you order the solenoid and wire it up to work? I have a 2014 and would prefer the stock later model unit without having to buy an entire tailgate from a 2016+. Wouldn’t mind the pop-a-lock, but have heard that they can be finicky.


Sent from my iPhone using Tapatalk
John Fleming Enthusiast

John Fleming

Posted
  • Author
Posted
10 minutes ago, NoLand said:


So did you order the solenoid and wire it up to work? I have a 2014 and would prefer the stock later model unit without having to buy an entire tailgate from a 2016+. Wouldn’t mind the pop-a-lock, but have heard that they can be finicky.


Sent from my iPhone using Tapatalk

I did not. I opened my tailgate up and it does not have the mounting provisions for the stock actuator so I just ordered the pop and lock. Actually just hooked it all up tonight. Seems to work pretty well. Of the dozen or so times I tried it I had a few that it didn't actually lock but I would say 8 out of 10 it did. Just seems like it needs a hair more travel to get it every time.

BigBlue2014 Enthusiast

BigBlue2014

Posted
Posted

I also installed the Pop & Lock in my truck. The install took about 20-30 minutes from start to finish and works flawlessly.

 

StWfR9M.jpg

  • 2 years later...
VirtualAnarchy New Member

VirtualAnarchy

Posted
Posted (edited)

I have a 2016 Silverado work truck with the 8 pin next to the spare tire. Does using all factory connections and wiring still require programming? The truck didn't come with a backup camera either from factory.

 

20220824_145824.jpg

20220824_145819.jpg

Edited by VirtualAnarchy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      I have an observation and a question... 1) I watch the voltage closely because I have had to dial in the cut-in/cut-out voltages of the battery separator to my camper.  The "smart" charging drives me nuts.  Anyway, I noticed that when coasting for a while, and especially if lightly using the brakes (though not necessary), the voltage goes up from mid/high-13 volts to mid/high-14 volts.  Then it drops back down after stopping or going again.  Consistently!   The only explanation I can come up with is REGENERATIVE BRAKING!  Well, maybe that's a little bit of an exaggeration, but it's certainly free extra battery charging.   2) Driving on mountain roads I will use L and vary the max gear.  Things straighten out and I end up in L10.  Sometimes I leave it there for a while.  Is there any difference between L10 and D?   
    • devonthegreat
      anyone interested in a 2002 Chevy Silverado 4x4 parts truck NYC

      By devonthegreat · Posted

      **SOLD** Please end or delete post. thank you
    • PBNB
      Tire pressure for 37s

      By PBNB · Posted

      Do you think this width might affect the chalk test with a higher pressure closer to 65psi? I think lowering the pressure makes sense to get the tread to lay flatter

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...