Jump to content

AT4 levelling kit failure

19AT4
 Share

Recommended Posts

19AT4 Enthusiast

19AT4

Posted
Posted

Well I thought it wouldn’t happen to me, but my ball joint failed, collapsed the UCA and pulled my CV shaft out while on the highway. I highly recommend upgrading to new UCA’s with any levelling kit. I only had 12,000km’s with it installed. 
 

I would have bought them but the new UCA’s stick out further in which you can’t run the stock wheels without spacers if you get bigger tires. I have no interest in running spacers. 
 

Some food for thought... 

19AT4 Enthusiast

19AT4

Posted
  • Author
Posted
15 hours ago, dane0254 said:

Sorry to hear that. I hope all is well. What is your plan now?

 

It’s at the dealer, waiting to see what all needs to be replaced. I see that motofab offers a 1” level that doesn’t require the strut to be pulled apart for the spacer. I hate the factory rake. Plus I had 35x11.5’s on order which I had to cancel. 

chizzoy Enthusiast

chizzoy

Posted
Posted

i saw on youtube that AT4 or RSTs with factory 2” lifts require new ball joints if raising or leveling.   Saw it on youtube and they stressed that.  not sure if this relates to your situation.  https://youtu.be/X1Pt00h5R3I

ullose272 Enthusiast

ullose272

Posted
Posted

Doesnt really suprise me, if you are using a 2" level kit on a at4 or TB, it would be like basically putting a 4" lift on a standard truck, all those kits come with upper control arms.

Sent from my SM-G973U using Tapatalk

  • Like 1
Twotrack Enthusiast

Twotrack

Posted
Posted

Sorry this happened to you. I was on the fence about even installing the inch motofab kit I have because I’ve been debating just holding out and doing the icon or mazzula kit with control arms and fox or kings. I think I’ll just hold out and only do it once now. 

19AT4 Enthusiast

19AT4

Posted
  • Author
Posted
21 hours ago, KillerOfMillers said:

What level kit did you use?

 

2” rough county, I called them about the failure. They said there’s no way their kit could have caused that, especially because my truck only sees highway driving. They blamed the shop that installed it. 
 

GM got back to me this morning with a bill of $1800 to get it all fixed. They said it was caused from the added stress but the mechanic said to use leveling kits that put spacers below the struts. He said you’ll be perfectly fine with that. 

  • Like 1
19AT4 Enthusiast

19AT4

Posted
  • Author
Posted
21 hours ago, ullose272 said:

Doesnt really suprise me, if you are using a 2" level kit on a at4 or TB, it would be like basically putting a 4" lift on a standard truck, all those kits come with upper control arms.

Sent from my SM-G973U using Tapatalk
 

 

There must be more than the eye can see, the CV angles were great with this level. That was one of my worries when I got the kit back in Jan. 

112379B5-2A3A-4E46-9AFB-74EDB3D03CA2.jpeg

KillerOfMillers Enthusiast

KillerOfMillers

Posted
Posted
2 hours ago, 19AT4 said:

2” rough county, I called them about the failure. They said there’s no way their kit could have caused that, especially because my truck only sees highway driving. They blamed the shop that installed it. 
 

GM got back to me this morning with a bill of $1800 to get it all fixed. They said it was caused from the added stress but the mechanic said to use leveling kits that put spacers below the struts. He said you’ll be perfectly fine with that. 

What exactly are they claiming was installed incorrectly by the shop?  It's funny how RoughCountry's 3.5" lift comes with upper control arms, but they're 2" level specifically for TB/AT4 which would stretch lift to 4" doesn't.  

 

This is the second time in the past couple weeks that I have heard of an upper balljoint failure.  Not gonna lie, driving to work this morning I thought about it and it made me nervous.  I didn't go the spacer route for my level, I used FabTech 3.5" coilovers and upper control arms, but I'm still uneasy. 

19AT4 Enthusiast

19AT4

Posted
  • Author
Posted
2 hours ago, KillerOfMillers said:

What exactly are they claiming was installed incorrectly by the shop?  It's funny how RoughCountry's 3.5" lift comes with upper control arms, but they're 2" level specifically for TB/AT4 which would stretch lift to 4" doesn't.  

 

This is the second time in the past couple weeks that I have heard of an upper balljoint failure.  Not gonna lie, driving to work this morning I thought about it and it made me nervous.  I didn't go the spacer route for my level, I used FabTech 3.5" coilovers and upper control arms, but I'm still uneasy. 

I don’t think they torqued the bolts properly when they had it all apart. I called rough country about it and they said there’s no way it should have came apart like it did. Especially considering all of the trucks miles are highway. I’m not sure what all’s different between the AT4 and non AT4 models but I know they got the extra 2” from longer struts. The angles all looked fine with the 2” level. 

19AT4 Enthusiast

19AT4

Posted
  • Author
Posted
Just now, 19AT4 said:

I don’t think they torqued the bolts properly when they had it all apart. I called rough country about it and they said there’s no way it should have came apart like it did. Especially considering all of the trucks miles are highway. I’m not sure what all’s different between the AT4 and non AT4 models but I know they got the extra 2” from longer struts. The angles all looked fine with the 2” level. 

Plus I put the truck on a jack and tested to see how the ball joints were. I was a bit worried from other horror stories I read. There was zero play. 

  • 3 months later...
JNG155 New Member

JNG155

Posted
Posted

I just had a ball joint failure on my 2019 AT4 yesterday with a Rough Country 2” levelling  kit.  65mph on the highway.  Almost had a head on crash.

ZDAT4 Enthusiast

ZDAT4

Posted
Posted

Prob not a mechanic, most likely the kit caused too much stress on the ball joint. The bad angles prob snapped your ball joint

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • pyoung62
      2026 DENALI 6.2L

      By pyoung62 · Posted

      I agree with Tim.  As tech heavy as engines are these days, no way I’d be an early buyer of the new 6.6.  Of course, I bought my ‘26 Denali w/the 6.2 after dumping my Tundra with it’s defective 3.5 liter imploding engine disaster, so I’m a little gun-shy.  That said, my 6.2 has been rock solid.  I don’t drive it like I do my BMW Z4 M40i, but I don’t baby it either.  I got a V8 for a reason.  But I’m averaging 18 around town and 22 highway.  I have seen 24 highway as well when I wasn’t loaded up heavy.  Considering my Tundra with the twin turbo V6 only got 14.5 in town and 17 on the road, I’ll take the 6.2 all day, every day.  If I were you, I’d grab a ‘26 while you can.  Inventories are probably gonna start dropping and I’ll bet the deals will start looking sweeter as well.
    • ShowMeShooter1332
      Can you add a 360° Cameras hard button to a 2021 Sierra?

      By ShowMeShooter1332 · Posted

      I am curious if anyone has figured out a way to add an hard button AUX or 360 Camera switch to the center row of switches. I have a 2021 AT4, and want to split the hill decent button and add a 360 camera button so that you don't have to go into the center display and locate the camera functionality, etc...   My father's 2024 Yukon XL AT4 and it has a hard button, see below. I found this thread on the Yukons, but it seems like there may not be a part number for the 2021 sierras. https://www.gm-trucks.com/forums/topic/255339-adding-hard-button-for-camera-on-2021/ Anyone else figured this out. Seems like it would need to be a custom switch!   I am getting ready to install the auto stop/start eliminator, so would be nice to knock them out at once.     Upvote1Downvote0Go to comments
    • Grumpy Bear
      Winter Returned

      By Grumpy Bear · Posted

      Looks like the entire state is burning. 😬
    • Chuck FB
      Oil Consumption

      By Chuck FB · Posted

      Through the years it hasn't been my typical method as I tried to drop oil on an engine that was hot from having been worked, however that was not always practical and had to fire up a unit and let it warm up reasonably well and drop the oil when I had the time to do it but am referring to not only vehicles but a variety of farm equipment and highway tractors etc. However on a vehicle where one is crawling under it and the exhaust is nearby to ones body and if wanting to pull the plug without danger of being hit with boiling hot oil or attempting to remove a HOT oil filter, its sure safer and easier to not have everything smoking hot and can remove the filter right away when under the vehicle and let it all drain. Of course its not the end of the world if a bit of oil stays in the engine that might have eventually found its way out, I like to get out as much as possible but any oil changes that take place in shops would rarely be sitting around for very long at all before the plug is thrown back in and filter slapped on and oil poured in and sent out the door quick like. There would be very little time spent ( assuming they even did it ) in starting the engine with oil to fill the filter, then waiting to verify the level on the stick. A good reason to check ones oil level shortly after a shop changed the oil on a vehicle just to make sure its correct and to look under for any oil around the drain plug or filter. 
    • CPhelps
      4 Wheel Drive System

      By CPhelps · Posted

      Cool to see another Vermonter!

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...