Jump to content

Recommended Posts

Posted
5 hours ago, newdude said:

 

 

If the harness has never been replaced at all before, you need both pieces because the original design harness is a one piece unit.  Once its been updated to the new two piece style, if in the event of future temp sensor failure you can then just buy the valve body half of the harness.  

 

The valve body its a 50/50 if it has to be removed to change the harness correctly.  Depends on if there is a connector in a certain spot on the harness or not.  

I understand much better now. I really appreciate your time to describe it to me.

Posted
22 hours ago, Sean_McNulty said:

Mine came out to $1057. The guy at service desk took off the diagnostic fee so that took $110 off. I can tell you that my truck hasn’t ever shifted as good as it did in the hour drive from the dealership. Feels like a whole new truck. 

Thats exciting, thanks for posting the results. Really hoping these random rough shifts stop as well.

  • 1 month later...
Posted

Thank you for the warranty information. I have a 2017 Yukon Denali 6.2 8 speed. I have the exact same issue. Same two fault codes (P0700 & P0711). I get the hard shifts occasionally. And at highway speeds of more than 65 mph it sounds as though I'm in 4 wheel drive even though it reads 2 wheel drive.

 

I also have the engine Ticking noise that started this past winter and never went away. Bugs the crazy out of me. Sounds like lifters but not sure. Any help with this noise would be greatly appreciated. 

Posted
18 hours ago, CMate said:

Thank you for the warranty information. I have a 2017 Yukon Denali 6.2 8 speed. I have the exact same issue. Same two fault codes (P0700 & P0711). I get the hard shifts occasionally. And at highway speeds of more than 65 mph it sounds as though I'm in 4 wheel drive even though it reads 2 wheel drive.

 

I also have the engine Ticking noise that started this past winter and never went away. Bugs the crazy out of me. Sounds like lifters but not sure. Any help with this noise would be greatly appreciated. 

I just started getting the same 2 fault codes in my 2017 Silverado 6.2 8 speed. Wonder if mine will be covered under this tsb? Even though it says it's only for 2016s I took delivery of my truck August 1st of 2016.

Posted

Had this done yesterday at dealer for my 2015.  Covered under extended warranty, which will expire in about 500 miles.

 

Seems to shift smoother than ever.   Probably also due to the clean fluid. The sensor was wonky for the last say 15k miles, but not bad enough to throw codes.

 

I had already drained and filled 8 speed on my own twice in the last 5000 miles (13 qts new fluid) then this - so the fluid is all fresh at this point.

 

It only took 100k miles to get this thing shifting nicely 😆!

  • Like 1
  • 3 months later...
Posted

I have a 2016 Yukon Denali throwing PO700 and PO711. Very rough shifting and stuttering. Nowhere on the special extended coverage release does it say 8 speed only. https://static.nhtsa.gov/odi/tsbs/2020/MC-10178408-9999.pdf 

I've got the 6.2L V8 with a 6 speed transmission. My dealer is backed up for 6 weeks because they can't get transmission fluid. From the release the fluid required is Mobil 1 Synthetic LV HP Automatic Transmission Fluid 19417577  which I can have delivered to the dealer by Amazon in 3 days. The dealer says GM must source the fluid themselves and will not pay for the repair unless it comes from GM which sounds nuts to me. Anyone else have this problem? Also, can anyone point me to a TSB or other release stating the extended warranty is for the 8 speed only? Thanks

Posted

I guess I got screwed on this. Last winter, i was getting the 700 and 711 codes but they went away and came back several times. Once the weather warmed up, the codes never came back. Fast forward to last month. Lifter started ticking so I took it in to the dealer. Asked them to check the temp and the A8 shudder. They fixed the ticking (bent push rod, 4 new lifters) but since no code was stored, no dice on the temp sensor. They then said the extended warranty would not cover the trans shutter, wanted $600 plus to flush. Ended up doing the sensor and fluid change myself. A little sloppy but not that bad. Sensor was only $65 or so. 

  • Like 1
Posted
On 9/18/2020 at 9:42 PM, 16sierra said:

FYI for anyone reading this thread, this only applies to the 6.2L + 8 speed. No luck on the 5.3L + 8 speed.

Is the fix the same for the 5.3L + 8 speed? Transmission Wiring Harness?

Posted
On 6/16/2021 at 4:30 PM, Differcult said:

I understand much better now. I really appreciate your time to describe it to me.

So you did ultimately get your 5.3L+8 speed fixed? Did yours have the 10-way or 4-way connector?

  • 2 weeks later...
Posted (edited)

I have a 2016 GMC Sierra SLT and went through the transmission shudder back in 2019 and the dealer did the flush at no cost to me now I had to go back this week for a P0711 TFT sensor / harness failure. I presented the special coverage # N192291660 to the service tech and he noted that this did not apply to the 5.3. When I asked him what is the difference we are talking about the 8 speed auto transmission the same as in the 6.2 to which he agreed. I called the division number for GMC 1-866-996-9463 and was told that there was a certain range of 6.2's that had this problem which made no sense to me what does it matter what size engine 5.3 or 6.2 and is beside the point. One thing for all GMC owners to keep in mind is that the average temp should be around 180 degrees plus or minus according to the load on the engine. I would suggest that if you are observing 135 degrees like I was should have brought this up before my warranty expired 6 months earlier this year, my bad. Anyhow I registered my complaint with the dealer and the GMC contact line.

Edited by Wayne Edward
correction
  • Like 1
  • 4 weeks later...
Posted

Thank you guys for this thread! Bought a 16’ Sierra 1500 Black Widow with 6.2L and 1 week later threw 0700 and 0711. Been driving it for a month until I started to do research and landed on this thread . At first GMC dealer in Houston said no special coverage for my truck with 109k (bought with 104k), but called GM and they said I did have coverage . Getting it repaired Tuesday for free! Car fax shows this truck had transmission work done around 45k miles but at this point just waiting on lifter failure. 

  • 4 months later...
Posted

Had the trans issue now,  almost out of warranty and the dealer covered it.  2015 Silverado LTZ 6.2L 8 speed. Looks like I got lucky :). Temps seem a bit drastic, but I think that is why it was failing.  Been shifting badly for years. Tried to find the parts they installed, but not what I've seen in this thread.

 

TransRepair.thumb.jpg.92511f3c98c9ca3b52462067588682d6.jpg

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,965
    Total Members
    8,960
    Most Online
    DaleB
    Newest Member
    DaleB
    Joined
  • Who's Online   2 Members, 0 Anonymous, 1,286 Guests (See full list)


  • Latest Articles

  • Posts

    • My truck is a ¾ ton but my placard also says 80 for the rear tires, I think I might have the upgraded suspension to the 3500 series maybe.   I put my air down to 60 and the light was still on, and there was no way I was putting over 60 psi in the rear empty and not towing because I knew the actual number Toyo gave me and I didn't wanna ruin the center of my tires!   And you actually can change it in the settings from metric or is and it will show kph or mph then when you go into your tire settings it will be either psi or kpa, but it would be nice to just change it directly on the tire psi page 
    • Common Sense Assembly   Your driveline is forgiving of the occasional mistake. It will even often forgive the random serious blunder. But it will not forgive a continuous bad habit.      What? Not everything needs to be a five thousand word essay.       
    • We drove about 15 minute east today to visit a friend and saw a steep increase in price in the same county. About 50 cents a gallon steepper. 
    • Sure about that? A degree wheel and a dial indicator would lower your degree of assurance in that statement. 😉    It why we have offset keys and dialable timing sprockets. Just say'n.... I've built a few and have never seen one "On the money". 
    • I will admit I haven't experimented much with pressure drops beyond the numbers I put in and part of that is that the numbers I used are fairly low and then found out it would trigger regardless at that 35 psi. Having said that I had tried before had changed the placard pressures and being that I have a 1 ton set to 80 on the placard for the rear I believe it triggered close to 60, the front I don't recall now for sure but thought maybe it could get close to 45 from that factory 60 placard pressure. So I never did figure out if it was a number of psi from placard pressure to the alarm or a percentage of the total placard number as some figured it was like a 25% drop from placard pressure would trigger it. So as to try and answer your question, I believe I set the placard pressure on the front to 47 or so and while I run the front tires at 40, they have dipped below that some if its colder and I haven't put "winter air" in yet and never once have had the front alarm go off. I would say that the answer your looking for is no, that if you set your placard pressure to 45, you have a certain amount of room to drop below that pressure before the alarm will go off.    The pressures you decide to run in your truck, that ends up being what makes sense to you based on what your carrying in your truck or if towing, then have to bump them back up to something that will carry the load in the rear and the fronts typically left at the same pressure. It all comes down to that chart I put the link to and using an accurate roadside scale to be your guide, both unloaded and then loaded to know your minimum safe pressures.    I just wish GM would allow a person to change the readings for the tire pressures to the English system of pounds as I have to look at that goofy metric reading that will never ever jive in my head and will go over and change it just to figure out what they are if need be and then change it back. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...