Jump to content

TPMS sensors loose signal right front wheel 2020 3500 HD DRW

Andrew Best
 Share

Recommended Posts

Andrew Best Enthusiast

Andrew Best

Posted
Posted

My right front TPMS sensor looses signal resulting in a service tire pressure monitor message as well as the TPMS warning light coming on. My dealer has changed the right front sensor but the issue persists. The truck has gone over a thousand miles without this happening or it can happen after a few miles. It can stay on for over an hour. Looking for suggestions.

  • 3 weeks later...
Revspan Enthusiast

Revspan

Posted
Posted

Same thing happened to me yesterday on a long trip.  

had the front left go first...then came back on, then front left and right rear went out.  Came back on in a few miles...  

redwngr Senior Enthusiast

redwngr

Posted
Posted

I'd take it back.

 

First attempt was a different sensor. 

Second attempt might be the receiving module on the truck. 

 

 

 

  • 6 months later...
KuiMonster Enthusiast

KuiMonster

Posted
Posted

I had this happen twice this year. Think a rear one and then today the front left did it. It goes away after a few miles. 

  • 4 months later...
  • 2 years later...
Truston Gunter Enthusiast

Truston Gunter

Posted
Posted

Any update or solution to this? I know its not the sensor, I've had the sensor changed while truck was under warranty but still same issue persists. Always same location, passenger front, also does it after tires are rotated so I know its not the sensor it's self. 

Screenshot_20240223_071834_Gallery.jpg

20240223_065905.jpg

  • 2 weeks later...
Truston Gunter Enthusiast

Truston Gunter

Posted
Posted
On 2/26/2024 at 8:06 PM, Gordon Lucas said:

Find the TPMS reset button, usually under the steering wheel, and hold it down until the light flashes three times. Start the car and let it run for 20 minutes to give the sensor time to reset.

dinosaur game

Is this the same as the "re-learn" procedure? If so, this gets done at every rotation and the same issue exists. Furthermore, it happens to be intermitted. Currently all sensors read fine, then the error will happen again for a day or 2 then go away??

  • 4 months later...
Truston Gunter Enthusiast

Truston Gunter

Posted
Posted

I don't believe my truck has this reset button under the steering wheel. Any additional info would be greatly appreciated. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • bwiese
      seat base height *lowering* (base 40/20/40 seat, 2026 1500 WT std cab)

      By bwiese · Posted

      Folks, Have a great new 2026 WT  (std cab, 2.7/4WD) w/base 40/20/40 mech adj bench "fake buckets"  (with lower and upper center console) heavy vinyl seats.  Overall the seats are very comfortable and the vinyl is heavy and appears less likely to 'split out'. Am very tall (6'5")  + a bad back/osteporosis/former hyperparathyroidism so ease/range of movement is a bit restricted.  The truck rides a bit high and I use a nerf step bar w/my left foot to step in, then I put right foot/leg in, drag my butt in  & get seated.  Worked fine in my 2018 RAM quadCab. But I end up dragging my butt over the left raised sidecushsion area of vinyl seat, and due to texture there's fair amount of traction on slide inward.  (ArmorAll didn't improve.) If the seat were even ~1/2" - 3/4" lower it'd be helpful, but base seats just have the forward/backward underseat bail and the side lever for tilt which really doesn't affect seat height.   I really don't want to 'de-puff' the left side sidecushion forming the  fake 'bucket'. I know one company sells 'seat elevator blocks':  but is there a simple way of lowering the height of the driver seat instead?   Thanks Bill W San Jose  
    • bwiese
      on-wheel cellphone control: 2026 1500 WT (2.7L 4WD std cab)

      By bwiese · Posted

      I have a basic 2026 1500 WT  (2.7L/4WD reg cab shorttbed). Comfy, generally happy with electronics/radio - but is there a way I can add switches to steering wheel right-side position (curr. empty) so I can adjust volume, push phone button to voice dial, etc? Bill W San Jose  
    • Tyler Gibbs
      Travel Trailer 2024 2500 HD 6.6 Gas Engine ?

      By Tyler Gibbs · Posted

      The curb weight on a 1 ton crew cab long bed is around 7k lbs.  Now, I don't know where you went to school but 9k is not more than 2x 7k lbs. More than 2x 7k lbs would be 14k+.   With that said, obviously yes you're going to feel a 9k lb trailer when slowing down.  I already said, when accelerating.  When changing lanes?  No.  But if you look at the context of what was quoted, the original person said, "after a mile or two..." which means that would be after the accelerating portion and you're driving a generally steady pace.  Please do learn to read and comprehend.
    • sFrank
      2026 Silverado Range AFM DFM ECU loaction

      By sFrank · Posted

      So I purchased the Range unit for my 2026 and I am seeing different locations suggested for the ECM . Can anyone confirm wither under hood, left side or right side or behind the wheelwell?
    • No F-bdy Bs
      Dave's Auto (custom engine builder) tear down of L8T

      By No F-bdy Bs · Posted

      Like I've said before. Di and Carbon buildup is not that big of a concern. Engine had minimal buildup, and that engine was obviously not super well maintained. Do regular oil changes, and you're gtg as long as the rest of the truck lasts. Also, the High Pressure FP that people ****** about, but can't tell you why.  Now, I wish they'd trash the variable oil pump. No real world issues with them, but I'll gladly eat whatever miniscule MPG it's saving me in favor of more oil at all RPMs.    Curious to see his assessment of the 7.3 compared to the 6.6. I expect he'll praise the port inj, but from a structural standpoint, the 6.6 is as robust as any engine out there.    Not to take away from the 7.3. I feel it's equally as good as the 6.6.     As to heat on the rear cyls, I'd have to see numerous examples before I'd say it's an issue. Especially not knowing the history of that engine. For all is known, they could have blown a rad hose, and ran it hot, and the 2 rear cyls may be the first to get hot in a low coolant situation, but not be an issue aside from that. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...