Jump to content

Service ESC light coming on in hot weather

Nhcampbells
 Share

Recommended Posts

Nhcampbells Enthusiast

Nhcampbells

Posted
Posted

Hello all

2021 2500 HD 4X4 with 4000 miles.

When we have temps above 90, and I start the truck the Service ESC light comes on and shows ESC is off on vehicle.

Then after sitting the next start it is fine.

Anyone else have this happen?

I will mention to the dealer when I have the first service, but with it being intermittent I'm not holding my breath for an answer from them.

Thanks for any ideas and comments in advanced.

Tomato Enthusiast

Tomato

Posted
Posted
16 hours ago, Nhcampbells said:

Hello all

2021 2500 HD 4X4 with 4000 miles.

When we have temps above 90, and I start the truck the Service ESC light comes on and shows ESC is off on vehicle.

Then after sitting the next start it is fine.

Anyone else have this happen?

I will mention to the dealer when I have the first service, but with it being intermittent I'm not holding my breath for an answer from them.

Thanks for any ideas and comments in advanced.

 

Have you pulled the DTC's or called OnStar for them?  I had an intermittent ESC issue with my 2015, and it turned out to be a wheel speed sensor.

Nhcampbells Enthusiast

Nhcampbells

Posted
  • Author
Posted
4 hours ago, Tomato said:

 

Have you pulled the DTC's or called OnStar for them?  I had an intermittent ESC issue with my 2015, and it turned out to be a wheel speed sensor.

I have not.

It's so new I'll just tell the stealership at the first service.

Just strange it is only on very hot days and not everytime at that either.

  • 11 months later...
Nhcampbells Enthusiast

Nhcampbells

Posted
  • Author
Posted

So a year later and the same thing is still happening, dealer found no codes.

Only when its hot out and comes on at startup the ESC system is off. No cruise available when its on.

Of course today I had it at the shop but no light till I got home go figure.

An ideas or has it happened to anyone else.

No DTC,s I will tr onstar when it happens again

Nhcampbells Enthusiast

Nhcampbells

Posted
  • Author
Posted

UPDATE: 6/28/22

Light came on this afternoon I was near the dealership at the time.

they checked for codes and found this.

"Lost communications with Steering angle and Electronic brake system".

Goes in for service next Friday.

Will update again if they find and fix the issue.

  • 4 weeks later...
Nhcampbells Enthusiast

Nhcampbells

Posted
  • Author
Posted
On 6/28/2022 at 6:33 PM, Nhcampbells said:

UPDATE: 6/28/22

Light came on this afternoon I was near the dealership at the time.

they checked for codes and found this.

"Lost communications with Steering angle and Electronic brake system".

Goes in for service next Friday.

Will update again if they find and fix the issue.

They found a bad connection in a module and repaired it. They did replace a steering angle module, that wasn't the issue. Tech back probed and found the the connection was loose.

  • Like 1
  • Thanks 1
Michael621 Enthusiast

Michael621

Posted
Posted

Thank you for reporting back about the issue. Glad they found the culprit and that will be the end of that nuisance!

 

nocturnalmotors Enthusiast

nocturnalmotors

Posted
Posted (edited)

2022 Chev 3500 LT Gas. I'm having an issue where when I'm parked in the sun and drive down the road after a mile or so, I hear a groaning / whirring down by the drivers kick panel. Almost like a phone vibrating 3-4 times then goes away. Did you have any noises? I don't have any MIL illuminated. In the morning or not hot out, no noise. If I lift my foot off the accelerator during the noise, it stops instantly. 

Edited by nocturnalmotors
  • 2 weeks later...
GMCustomerService Senior Enthusiast

GMCustomerService

Posted
Posted
On 7/26/2022 at 11:33 AM, nocturnalmotors said:

2022 Chev 3500 LT Gas. I'm having an issue where when I'm parked in the sun and drive down the road after a mile or so, I hear a groaning / whirring down by the drivers kick panel. Almost like a phone vibrating 3-4 times then goes away. Did you have any noises? I don't have any MIL illuminated. In the morning or not hot out, no noise. If I lift my foot off the accelerator during the noise, it stops instantly. 

This is certainly not what we like to hear, nocturnalmotors.  Please know, customer satisfaction is extremely important to us. Our team would be more than happy to take a closer look into the concerns with your 2022 Chevy 3500 LT. To do so, please send an email to [email protected] with ATTN: nocturnalmotors/GM Trucks in the subject line.

Please include your contact information, VIN, a brief description of your concern, and the name of your preferred dealership. We look forward to hearing from you. To learn more about GM’s privacy policy, please visit https://www.gm.com/privacy-statement.html.
 
Privacy Statement | General Motors
Your privacy is important to General Motors. This Privacy Statement addresses the personal information GM collects and how GM handles that personal information.
www.gm.com
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      2024 Silverado 2500 HD with the 6.6 Gas (L8T) Engine

      By Chuck FB · Posted

      How many miles were on the truck when you bought it and was there some form of oil change history generated through a dealer or an independent shop although not much would show up if the owner had changed their own oil. Just curious if it was a maintenance issue or if there was something off from the start, surely one would think the original owner would have realized it was using a lot of oil, its hard to go back in time and find out the true story of mysteries like this. Well hopefully the warranty company will go for it and just install a new engine, that would be the ideal outcome.    I still have so few miles on my truck as per not quite 9000 and will be changing the oil shortly which has around 2700 miles on it or so and its down so little on the dipstick from where it was at the beginning of this oil change that I could make the "claim" that it uses no oil but in reality would be a very small amount, less than a 1/16 of an inch. Just driving empty/not towing and easy driving so hard to say what it would do if it had a load behind it for oil consumption. So far very impressed with the very minimal oil usage. 
    • BIGBOYS
      Doors lock and mirrors fold in while driving

      By BIGBOYS · Posted

      I have a 2015 Silverado and sometimes I can not get in to the truck. I use the key to unlock the driver door. Something is locking the truck when I unlock it, last night I left the truck open and this morning it was locked with the mirrors folded in. This happens while driving so it is now a safety issue. I reach down for the folding button and they open, then they close again.  Any advice, thank you,   Ed
    • Paul8556
      Headlight issue...

      By Paul8556 · Posted

      Did you ever find a resolution to this? my 2019 Silverado 1500 is showing the exact same headlights issues with the exact same symptoms.  would help a ton if anyone has any advice on this or better yet a known solution..
    • RyanbabZ71
      Gas Prices

      By RyanbabZ71 · Posted

      Wawa and Meijer here have ethanol free (88 & 89) I use for my mower and lawn equipment.  Its not much more than reg.  I paid $3.29 a few weeks ago.  
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      tl; dr I've now reached the 6th floor of hell. I'm chronicling my journey for my morning readers.   Pulling the top of the intake apart was moderately easy but it involved a lot of parts, connections, and minutae. I was preparing for the new fuel lines to arrive ("nut and bolt kit" it's called). The fuel line connections are notched and held in place by the manifold and a metal plate with a T27 screw.   It's on the back of the intake, under the firewall, with little clearance, and two hard metal fuel lines in the way. I was using Franken-tools (weird combinations of 1/4 inch ratchet with/without an extension, with a bit holder for my T27) to get in there. One of my sockets and bits fell off and has yet to emerge on the floor. I lost a second setup and that's when I almost started throwing tools. But that was the point at which I had gotten traction on the Torx head, and it promptly stripped. No more traction.   I started humming "1-877-kars-4-kids" because I was about at that point. You know what? I'm $1500 into this thing and I can make it disappear just as quickly. This isn't fun anymore. I had spent a lot of time already "tidying" around the engine bay: Fixing all the "someone's been here before!" BS. The truck has been exclusively dealer- and shop- serviced and I'm reminded of why I never let other people work on my cars unless absolutely necessary.   Speaking of dealer service. This truck has a 1" stack of records going back to 1995. I put them all in an excel spreadsheet, date/mileage/description.   The CPI spider has been replaced 4 times in 85k miles. The EGR? Another 4. Multiple, multiple O2 sensors. One Cat. 4? Sets of plugs and wires, and I swear half the stack is diagnosis paperwork for "misfire, runs rough, extended crank, dies at stoplights".   GM was producing some proper crap back then. And it was still well within the era of brittle/crappy plastic. (Windows 95 was released the same month this truck was sold new, we HAD the technology!!)   There (was) a plastic shroud around the evaporator core and HVAC fan in the engine bay. I noticed a chunk of it missing so I poked at it some more and it literally shattered. Touched it some more and pieces were crumbling off. Had a good laugh. Clearly whatever plastic garbage they were using had broken down over 30 years and was literally turning to dust. That was a good half hour of using a shop vac to remove the rest of it.   Back to it.   I was going to give up for the evening but then decided I'm already level 10 pissed off at the stripped screw: G* D* it, give me my tools back -- and my JOY. We'll do this the hard way: The whole intake is coming off.   Blazer won Round II. After finally finding and accessing the 12 intake bolts and using a pry bar to unseat it from the heads, it popped loose in an explosion of gunk and grime raining down into open ports. Awesome.   6 times I reminded myself: Be careful of the temperature sender on the front of the intake.   YEAH, I forgot again and snapped it clean off in the removal. Add another $20 to the ever-growing list of new parts this thing is consuming.   The shame is, long before removing the intake, I had changed the oil in prep for Tuesday's momentous fuel line replacement that was going to be the magic fix and I'd have a running Blazer to tool around in this next weekend. The intake removal, including raining gunk, also gushed dirty coolant all over the valley. Of course it did. Welp, there goes another $35.   I now need an intake gasket set, bolt set, coolant temp sensor, another 5 quarts of oil, some RTV. Don't worry, I've already got 3 new jugs of Dexcool and a thermostat waiting. I'll fill it with clean water first to get it running, dump it, and then add the Dex later on in case... well, let's not go there. I'm only tearing this down once, next time the truck is going on Marketplace for FREE.   Oh, and I'm going to need vacuum hose for all the stupid connections placed at the rear of the engine which have since disintegrated. Come on, GM....tell me you don't do that anymore?   Oh, and the ears on the distributor where the cap screws down are both cracked. I mean, why not put a new distributor in it too. You get a distributor, YOU get a distributor, Everyone gets a new distributor!   This truck isn't out of the woods yet...I'm already questioning how much more time I'm willing to sink in.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...