Jump to content

Coolant Leak 2015 Sierra

SkiDooNick700
 Share

Recommended Posts

SkiDooNick700 Enthusiast

SkiDooNick700

Posted
Posted

Hey guys,  2015 GMC Sierra 6.2 NHT April 2015 build. 

 

All of a sudden I've got a coolant leak but haven't been able to pinpoint where from.   I see the drivers side frame wet and will drip to the ground.   Coolant level already down up to 2 inches from Cold line.   It's even wet on the back side of the lower valence. Just noticed this leak after a 200-300 mile trip back from vacation.  

 

Dried up the frame,  took it on a 3 mile drive,  already dripping with coolant.

 

Any advice? I am not sure where else to look - might need to start pulling stuff off the truck to get a better view?

Is my truck build date part of the known TSB? Is it possible to see the stress cracks per the TSB without disassembling anything?

 

 

20210804_175635.jpg

SkiDooNick700 Enthusiast

SkiDooNick700

Posted
  • Author
Posted
55 minutes ago, Snowcamo said:

Bottom of the water pump usually has a weep hole. Try there. That's not to bad of a job if your mech inclined.

 

I will have to take a look to see if it is wet.   It didn't cross my mind to check it.  

 

50 minutes ago, CamGTP said:

$5 it's the radiator that needs to be replaced.

 

I am worried this may be the case lol.   There is like a tray or something running under the radiator and it is wet all along it from what I am able to see visually. 

SkiDooNick700 Enthusiast

SkiDooNick700

Posted
  • Author
Posted (edited)
10 hours ago, CrawlSlow said:

I would start with the easy stuff first before taking things apart.. Drain plug, check along side of radiator to see if it's wet.

 

Thanks for the tips.  Is the drain on the passenger side? 

 

As far a checking the sides of the radiator,  I swear I've looked at every possible angle top and bottom left and right and I am not able to get a clear visual of the sides of radiator. 

 

I watched a video it seems like a pretty quick process to remove the top cover piece,  air box, and fans.   Thinking this might help my view out. 

Edited by SkiDooNick700
SkiDooNick700 Enthusiast

SkiDooNick700

Posted
  • Author
Posted

Well guys looks wet at drivers side corner of radiator.   I'm thinking it is cracked somewhere?  Going to try to pressure test.

 

It was pretty easy to get the fans out the way,  just took me a while to figure out the clips and such.   I need to buy the right tool for the job lol. 

20210805_175819.jpg

  • Like 1
SkiDooNick700 Enthusiast

SkiDooNick700

Posted
  • Author
Posted
On 8/4/2021 at 8:06 PM, CamGTP said:

$5 it's the radiator that needs to be replaced.

 

You appear to be the winner!  Took some things apart including removing fan shroud.   Did a pressure test,  the drivers side corner of radiator is leaking.  It was a pool in no time. 

 

Now to find a new one,  looks like GM replaced with a new part number. 

  • Like 1
SkiDooNick700 Enthusiast

SkiDooNick700

Posted
  • Author
Posted
4 hours ago, Gagliano7 said:

https://www.rockauto.com/en/catalog/chevrolet,2015,silverado+1500,5.3l+v8,3307665,cooling+system,radiator,2172

 

Thanks yep I used RockAuto to figure out the updated number.   Called a local "dealer" who has one in stock,  about 350$.  Had to purchase via their website to get that price otherwise they have to sell for 500+ in person. Something about GM e-commerce policy. 

  • Like 1
Ravenkeeper Senior Enthusiast

Ravenkeeper

Posted
Posted
On 8/4/2021 at 5:00 PM, Snowcamo said:

Bottom of the water pump usually has a weep hole. Try there. That's not to bad of a job if your mech inclined.

Usually when the water pump plug goes, it's a huge mess, and not driveable.   It will blow out all of your coolant.

 

On 8/6/2021 at 6:39 AM, SkiDooNick700 said:

 

Thanks yep I used RockAuto to figure out the updated number.   Called a local "dealer" who has one in stock,  about 350$.  Had to purchase via their website to get that price otherwise they have to sell for 500+ in person. Something about GM e-commerce policy. 

Cheaper than RA?

SkiDooNick700 Enthusiast

SkiDooNick700

Posted
  • Author
Posted
7 hours ago, Ravenkeeper said:

Usually when the water pump plug goes, it's a huge mess, and not driveable.   It will blow out all of your coolant.

 

Cheaper than RA?

 

Rock Auto has it for 335 plus $20 shipped.   It was more or less a wash.   At that point I said to myself let me get locally if I can instead of having a radiator potentially tossed around by UPS or FedEx.

 

Finished install of new one last night,  took on 20 minute test drive.  All seems good so far.   I need to do a good washing of the engine bay now, there is so much coolant still down the frame and such lol. 

 

I think I am going to order a new T Stat, my temp gage always fluctuated a tad but very very recently (last 100 miles)  it's doing some big swings, from 210 down a line and back up to almost 210.

 

Also my idle seemed kinda rough yesterday not sure what is up with that.  She's going through a phase!

  • Like 2
diyer2 Senior Enthusiast

diyer2

Posted
Posted

 instead of having a radiator potentially tossed around by UPS or FedEx.

 

They delivered the part you bought I bet. 

Z45 Senior Enthusiast

Z45

Posted
Posted (edited)

There was a service bulletin on leaks, had my 2015 repaired under warranty for leaks.  In short faulty thermostat cause radiator failure.

Quote

This condition may be the result of excessive thermocycles within the cooling system caused by excessive cycling of the thermostat. These excessive thermocycles within the coolant system may cause the tubes to fatigue, crack and leak at the radiator headers. To correct this condition, a new thermostat has been designed that eliminates the
thermostats excessive cycling.   If this condition is found, in addition to replacing the radiator, the engine coolant thermostat housing (w/thermostat) must also be replaced. Refer to Engine Coolant Thermostat Housing Replacement in SI, which is located in the Engine Heating and Cooling section.

 

https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&ved=2ahUKEwiA-7iSyqvyAhUIVc0KHd6zACMQFnoECAYQAQ&url=https%3A%2F%2Fstatic.nhtsa.gov%2Fodi%2Ftsbs%2F2019%2FMC-10155058-9999.pdf&usg=AOvVaw2ifEl9-OC04g37-bj7JXC2

Edited by elcamino

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • richard wysong
      Wow I'm in a pickle. (Broke down truck) and a story.

      By richard wysong · Posted

      The timing marks are ok, that is #1, you can turn it over until they line up and it won't change anything, the crankshaft turns twice for every camshaft revolution, I have always set up SB Chevs as your pic shows using a straight edge
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Someone's been here before.... There is a receipt for a 3-piece timing set, purchased earlier this year.   Is this picture something, or, nothing?   I have the timing cover off and my crank is perfectly TDC and the keyed gear's locating mark is dead on 12 o'clock.   The cam gear locating mark is also at 12 o'clock. Now, I'm not an expert, but all the install guides say the two locating marks should meet and be perfectly aligned when installing a timing set. The mark on the crank should be dead on 12:00 and the cam gear's mark should be dead on 6:00, and both marks should be perfectly vertically aligned.   I believe the timing gear is keyed or has a dowel that ensures it can only be installed on the cam in one position, so I have to believe the cam is out of phase somehow. At the very least, with a triangular bolt pattern, it can only be installed in one of 3 different positions.   Before I pulled the front cover, the truck was running alright, no service engine soon lights except an occasional P0172 / rich condition. Timing -16 timing at idle (should be +16), and total -35% fuel trim, two conditions I haven't been able to figure out.   In related news, my injector tested pretty well, wasn't leaking, but I had it rebuilt anyway, and it's on it's way back to me.         Along with this discovery, the good and bad:   Good: The oil pan seal appears undamaged.   Bad: -The timing cover has been reused, and the positioning dowels have been broken. That could explain some of the leaking. -Some kind of white paste or grease was used to try to seal the oil pan seal and timing cover (since wiped off..). -Then, someone globbed silicone all over the front of the cover and also buried the ckp sensor in it. But, they didn't put any inside the cover or use RTV to try to seal the oil pan seal with the timing cover (good).
    • Grumpy Bear
      PF63 Oil Filters Going Away?

      By Grumpy Bear · Posted

      The guy that owns K&P filters last I checked in with him has over 300,000 miles on his Dodge base Hemi using his own 35 micron absolute stainless mesh filter from its first oil change.    The GM study I've posted a dozen times shows the relationship in engine life based in multiples of base units, not miles or years. That is the base unit is the number of miles the motor ran using the reference filter efficiency.    The above two paragraphs dismantle anecdotal arguments IF one changes oil often enough to prevent particle formation and the motor is in otherwise good shape. That is not full of silica (no air filter) or suffering a metallurgical issue that is not part of the lubrication discussion. Poor heat treat in example.   Data from UOA's I've reviewed from more than a few engines can show remarkably broad variations in oil cleanliness using the exact same filter over the course of an engines life.     Lastly there is the common sense of it. Wear debris WILL circulate the engine BEFORE it ever sees a filter in route to that filter and WILL harm the pump which NEVER sees filtered oil.    Alpha question then becomes, given the facts, how long do you believe is a reasonable service life from a vehicle you are certain you will not pass down? That is the junk yard will be it's resting place when you're done with it? (the moral issue most don't care about).    Omega question is then how diligent are you prepared to be in general mechanical, air & oil maintenance? Preventing particulates and keeping them sufficiently dilute; preventing the precursors from generation, amalgamation and precipitation.    If I get a good look at the engine bay of a vehicle I have a fair idea of the owners commitment to the inside of the power train. That 30 micron WIX is still more efficient than a sieve.                 
    • Tyler Gibbs
      PF63 Oil Filters Going Away?

      By Tyler Gibbs · Posted

      It also depends on what criteria someone is using for “best” when talking filters.  Are we going off best efficiency?   Best quality/QC?  Etc. because the two may not mutually exclusive.  
    • Tyler Gibbs
      PF63 Oil Filters Going Away?

      By Tyler Gibbs · Posted

      They’re not the same wiz as 10-15 years ago.  QC has fallen pretty hard.  The XP line was never good though in the first place.    https://bobistheoilguy.com/forums/threads/wix-filter-rusted-through.386492/post-6991372   https://bobistheoilguy.com/forums/threads/i-ve-used-my-last-wix-filter.27299/   https://bobistheoilguy.com/forums/threads/looking-for-a-better-replacement-for-wix-51258.403977/   https://bobistheoilguy.com/forums/threads/convince-me-in-using-the-purolator-boss.401537/post-7420147   the forums are littered with posts and examples of not great wix filters the last couple years 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...