Jump to content

03 6.0 2500hd: Reduced engine power, at my wits end

Terinass_sydwayz
 Share

Recommended Posts

Terinass_sydwayz New Member

Terinass_sydwayz

Posted
Posted

I have been trying to track down the source and fix REP since I bought this truck about a month ago. 

Codes observed are:

P1516 TAC issue

P0220 throttle B circuit

P2135 Throttle pedal a/b mismatched 

 

I have tried the 3 min running 30 secs off 3 min running relearn and the REP pops Everytime on the 2nd 3 minute mark. It will run like trash, if you shut it off for about 15-20 seconds CEL will be on but seems to intermittently run ok before the code comes back.

It seems to be a wiring, TAC, or PCM issue to me. 

I've about done about everything I can on it.

I did buy a big scan tool and will experiment with it later tonight, but I'm really uneducated on how to monitor it or reset and relearn the right data with this Autel MaxiCOM MK808BT PRO Scanner I purchased hoping to solve this.

Here are the things I've done to troubleshoot this problem:

 

TPS, TAC, APP wires greased

PCM1 10a fuse replacement

Pass engine block ground cleaned, recrimped, greased, added ground

Drivers engine block cleaned, recrimped, added ground

Hood to firewall ground added

Block main ground cleaned, greased and reattached

Alternator charging wire larger gauge new wire

PCM checked, no burnt pins, gasket is pinched and could have let moisture in, but everything looks good otherwise

TB replaced

TPS new pigtail soldered in

2 different TAC modules from the junkyard swapped in with same similar results

1 APP pedal swapped in from the junk yard with matching TAC and wiring harness.

 

Any guidance or help is appreciated greatly. Need a next step to follow 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Buckwild27
      Gas Prices

      By Buckwild27 · Posted

      I agree. 
    • Atlas
      Gas Prices

      By Atlas · Posted

      87 down as low as $5.14 here... winning!
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Progress... sort of.   Intake is disassembled, spider is out, fuel lines removed. Used a torch on the stripped screw with the lower intake off, much easier when I've got the intake sitting on my workbench, I made it talk. Walked right out with a pair of vice grips once it was nice and toasty hot.   New parts are piling up on my service cart waiting to be installed. Distributor, temperature sensor, new gaskets, fuel line kit, themostat, water neck.   My new pickle is I don't want to spend $600 on a replacement spider. I'm not sure IT is bad. I'm probably splitting hairs. Or it's $300 to send mine away and another 3 weeks of the truck just sitting. I have half a mind to assemble everything with the old spider to see if I can get away with just replacing the fuel pressure regulator to be safe. The obvious issue was the gushing high pressure fuel line which will be replaced. Getting to the spider really isn't that hard, and now I know what I'm doing , swapping it would be a breeze should it absolutely need one. Stupid, or smart?   The part that gives me pause is replacing the distributor. Well, it's already out. And I didn't mark it, whoopsie! Engine was at TDC when I removed it, I know that, so upon correct reinstall the metal tip on the rotor should point to the TDC mark on the distributor because that's where it was pointing on the old distributor. Worst case I'm a tooth off and have to re-stab it.   But then, what? I assume the truck will start. It doesn't appear the timing can be set. Here's the problem: These distributors can't be rotated but a degree or two, by design. What I read is Cam ****** needs to be -2 to +2 degrees, ideally at 0 (and checked/set above 1000 rpm). There should be enough wiggle to get that properly set, but checking the reported value is another potential issue. My Actron 9185 scanner says it supports enhanced GM PIDs and Cam ****** is one of them but it's unclear that I'll be able to correctly see it over OBD 1.5. I can see why people end up junking these things with life left in them. They're an absolute nightmare with tweener-year diagnostics/electronics and unobtanium parts.   Fingers crossed it starts and idles nicely. There can be hope, right? I'ma buy a lottery ticket the same day just in case.   Next steps..DO IT. I have not installed an intake before so I've been reading and watching a lot. Some say NO RTV except on china walls, some say DO RTV on water ports but not fuel/air intake. 1/4 or 3/8 bead on China walls? I think my strategy will be, obviously, RTV china walls with overlap on the gasket corners. Chapstick-style RTV the water ports. Leave intake ports dry. The only set of intake gaskets I could find locally are Edelbrock performance gaskets (uh...for an asthmatic 190hp V6? LOL) so we'll see how they do.   #NoToolLeftBehind. It took an hour, but my recovery mission for my deep 10mm socket was successful. It had rolled down the bellhousing and wedged itself between what I think are the fuel lines? I couldn't see it at all, but with a junk antenna I had laying around, I blindly went poking/sweeping for it, heard it clink, raised the truck, and caught a sliver glimpse of chrome with a flashlight way up there in Narnia. I had pushed it farther along the lines holding it captive, but within access of severely improvised tools, poking and cursing at it to finally knock it free to where I could get a fingertip on it to bring it home.    Not much to see.      
    • RyanbabZ71
      Gas Prices

      By RyanbabZ71 · Posted

      Thats crazy considering im right next door (Indiana)
    • Black02Silverado
      New Retail & Commercial Promo

      By Black02Silverado · Posted

      For a limited time, retail and commercial accounts receive an AMSOIL Vinyl Tool Tray with their order of $500 or more when they use code TRAY726 at checkout. The promotion runs through July 21, 2026.   Order at https://syntheticadvantage.com   Want to use AMSOIL in your business or sell at your store, apply here.  https://www.amsoil.com/business-opportunities/?zo=521390  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...