Jump to content

Recall!

compulynx

Recommended Posts

urbancowboy Enthusiast

urbancowboy

Posted
Posted

bought my truck in the states as i live in canada, wonder if my local dealership will cover this or will i have to go to the states to have it changed. i get covered when i get 7500 miles on it in canada, maybe wait till then. any one else run into this ?

Darkanion Senior Enthusiast

Darkanion

Posted
Posted

I was reading some stuff a few days ago about the NHTSA investigating fires in most of the vehicles that are on this recall list. I wonder if the two things are related... If so, there's no way I am NOT getting the wiring harness replaced, with my truck being parking in my garage most of the time.

HawkeyeOC Senior Enthusiast

HawkeyeOC

Posted
Posted

Hmm...have a dealer "mess" with a wiring harness or risk my vehicle being burnt to the ground. Tough decision. :uhoh:

 

What are some of you guys talking about...GET THE RECALL TAKEN CARE OF!!!

HawkeyeOC Senior Enthusiast

HawkeyeOC

Posted
Posted
The next time I have snow on my windshield will be the first !

 

It's also good (although not anywhere near perfect at this) for getting bugs and other crap off the windshield in warmer climates :uhoh:

compulynx Enthusiast

compulynx

Posted
  • Author
Posted

Well, I feel a little better. I went back and checked the sticker. I do have the heated mirrors, but not the heated washer fluid. Whew!

 

C

iscsidude Enthusiast

iscsidude

Posted
Posted
The next time I have snow on my windshield will be the first !

 

It's also good (although not anywhere near perfect at this) for getting bugs and other crap off the windshield in warmer climates :D

 

 

So that's what they are for ! :uhoh:

 

I've never turned them on so I'm not sure they even work. :D

HawkeyeOC Senior Enthusiast

HawkeyeOC

Posted
Posted
The next time I have snow on my windshield will be the first !

 

It's also good (although not anywhere near perfect at this) for getting bugs and other crap off the windshield in warmer climates :D

 

 

So that's what they are for ! :D

 

I've never turned them on so I'm not sure they even work. :D

 

 

Try testing it out in an open area. If you see smoke, they are sort of working :uhoh:

robertbick Enthusiast

robertbick

Posted
Posted

Mine work. One day filling up with gas, my son pushed the button. I guess it takes 30 seconds or so to heat up the water becuase when I got in, it started spraying the windshield and I thought something started smoking. It was just the steam from the heated water. Haven't used it again since then but might use it this winter if needed.

iscsidude Enthusiast

iscsidude

Posted
Posted
The next time I have snow on my windshield will be the first !

 

It's also good (although not anywhere near perfect at this) for getting bugs and other crap off the windshield in warmer climates :D

 

 

So that's what they are for ! :D

 

I've never turned them on so I'm not sure they even work. :D

 

 

Try testing it out in an open area. If you see smoke, they are sort of working :uhoh:

 

 

 

Burn Baby Burn !!!

DofD Senior Enthusiast

DofD

Posted
Posted

Very interesting! I wonder if the 2009s already on dealer lots will be affected?

 

Since all they are doing is installing an inline fuse I don't think that it is a large harness replacement. probably just the lines from the washer heater element to the BCM and battery.

 

This problem could very well be related to the NHTSA engine compartment fire investigation.

HawkeyeOC Senior Enthusiast

HawkeyeOC

Posted
Posted

Hmm...good bonfire starter for this holiday weekend. 4 by it out to the beach and park it, turn the washer fluid button on and POOF! :D Instant party. :uhoh: The GM buys me an '09 with bluetooth or I wind up in jail :D:D:crazy:

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • fondupot
      Exhaust heat while towing!

      By fondupot · Posted

      You can install tailpipes that direct the exhaust sideways vs the OEM one that goes straight back. There are several on the market, do you own research. HOWEVER, you need to make sure the Venturi vents are still intact, otherwise it will throw a engine code. There is a sensor somewhere that detects back pressure on the exhaust. And if it doesn't collect the correct metrics, it will throw the truck into limp mode. 
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      "Teardown" is complete. Head surfaces are clean and ready, new intake is prepped and ready. Coolant drained and water pump is removed, radiator is removed, new hoses and pump are ready.   The replacement intake is also from a '95 (with I think 260k, the odometer said). Noticeably less pitting where it covers the rear coolant passages. I'm not sure if that's a tribute to more frequent use, more frequent coolant changes/upkeep, or if the intake was machined at some point. But it appears I found a good one.   My coolant hoses were original, and the lower hose still retained the factory spring inside. It's not really rusty, but it's got deposits all over it. Unsure if I should re-install it (will thoroughly clean it first). Someone said hose technology has gotten better since 1995 (has it?) and I don't need the spring. I think modern EPDM is what made those hoses last from 1995-2026, so it's a question of how much suction can the water pump really pull, and will it collapse the hose without a spring?   I'm stopped and waiting for parts, however.   When I first brought the truck home, the fan was intermittently hitting the radiator shroud. I could see someone had monkeyed with the shroud (put a bunch of cardboard as a spacer between the upper/lower shroud halves. Someone said the motor mounts have likely failed and the engine has sagged. I wasn't sure I believed that. The engine is really solid in its mounts: To remove the old intake I *just* nearly permanently welded to the heads with freshly cured RTV and gasket snot two weeks ago, I literally had to use the arms on my lift and a chain with a bolt attached to the intake to pull it loose. It almost picked the front of the truck off the ground before ....scuuuuuuuuuuup.... I could actually hear the gaskets tearing and it broke loose and the whole truck settled back down. Motor barely moved.   SO, those parts I'm waiting on... The lower radiator mounts/bushings had completely failed. The radiator needs to be insulated from the rad support, and the bushings help the rad stand at the correct height. The plastic "baffle" was also destroyed at some point. Someone had attached the shroud to it incorrectly, overlapping a joint that should have been underlapped, creating another suspect issue potentially causing things to hit the fan. Broken tabs, side is busted off, and it's perma-formed/bent where it was jimmied incorrectly.   The baffle? Unobtainum. Long since discontinued from GM, of course. Aftermarket/capa/chinese? Also unobtanium. In GM's infinite wisdom, it appears there are at least two different variations whether the Blazer is 2 or 4 door, and I can't yet tell if they shared the same part with the S-pickups. Plan B, if I can't find a viable used one, will be to create a bracket to re-assemble the critical joint I need to seal a gap with the shroud. But that will bug me, it won't be...perfect.   The water pump bolts appear to have been installed with...plumber's putty. I guess, sure, if it works...? I've found a few "backyard fixes" like that. Someone's been here before....   If I can't find someone to jam bamboo under my fingernails to fill my free time this week I think I'll install the driver's power window motor and replace the rear door speaker that's inop. I've got a genuine GM "9.5" ohm working replacement. Why GM used a non-standard resistance....nevermind. Of course they did, you can get more sound from a cheap factory amp that way.   And the saga goes on...
    • glenn27
      Different requirements for oil filters?

      By glenn27 · Posted

      // Thank you, also for your  response. More information is always good. This 2013 GMC is most likely my 'forever truck"-I'm 77 and retired...and truck only has 42K on it-very clean-so I try to keep it that way.  Tks again for your  response- glenn
    • smooth68
      Alternate wiring for Kicker sub with Bose system. (DO THIS)

      By smooth68 · Posted

      I started my install this weekend. Everything was pretty straight forward but I ran into one issue with running power through the firewall. The nipple grommet on my High Country already has a small harness running through it - has anyone else ran into this issue? And on the engine bay side, does the wire basically just penetrate the factory wiring boot? I did this on my '22 Trail Boss and it seems much easier but thats been a few years. My other thought would be possibly drilling a new hole adding a rubber grommet just to the lower left of the factory hole. Thoughts?   Has anyone used a T-harness off the Bose amp and obtained power from there? It seems a little odd that such a small amp needs 3 power leads
    • glenn27
      Different requirements for oil filters?

      By glenn27 · Posted

      ///// Ok--Thanks for that info--I could not find yesterday when I looked for the specs on that NAPA filter what I wanted. Their website is not very user friendly. I buy all teh filters for  our three vehicles once or twice a year. Have always run NAPA Gold on everything I own....I buy it thru my Son's account for his business-which he has a Heavy Equipment repair shop-one reason he uses NAPA so much-they have such a full line of coverage for just about anything/anywhere- He gets s  good discount because of volume bought. Anyway-Thank you -Sir for your response.   glenn

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...