Jump to content

LED Under Rail Bed Lighting

b1gted

By b1gted
in Modifications & Accessories

 Share

Recommended Posts

duncrunner New Member

duncrunner

Posted
Posted

Hey guys wanting to install a set of LED strips but don't want to tap into the cargo light for power since I want to use them without getting into the cab or having the aux power on. Read on some other forums that there is a hot wire running to the trailer harness.

 

Anyone tap into this for their lights? If so, did you have to hook up any wires/fuses in the fuse box?

  • Replies 399
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

block8head
block8head

Here you go...

electricchiken7
electricchiken7

I installed the after market ones. I tied them into my cargo lights. Great mod!!     Sent from my Galaxy Nexus using Tapatalk    

corwest
corwest

Just as a heads up: The junction box comes with a cover for the plug that these plug into. So I made my own plug out of the cover with a couple parts from other plugs i had laying around and sealed

Posted Images

ls2gto Enthusiast

ls2gto

Posted
Posted

I just started doing that ^^^ Tonight. Found the red/white wire going to the 7 pin trailer plug to be live. Spliced into it with an in line fuse and went to a toggle switch in the box and am also wiring in a door pin switch for the tailgate. Will be finishing up tomorrow and hopefully everything works as planned.

2017SierraSLT Senior Enthusiast

2017SierraSLT

Posted
Posted

I wired my 4 LED under rail bed lights through the live 12V in the 7 prong trailer harness, and added a 5 amp inline blade fuse. I used a GM door jamb pin switch in the tailgate jamb. Others have used a mercury switch inside the tailgate.

  • 3 weeks later...
jsrx05 New Member

jsrx05

Posted
Posted

For those that have installed a second OEM set of bed lights, are you willing to part with the plug end that you are not using?

Ex-Ford Guy Enthusiast

Ex-Ford Guy

Posted
Posted

For those that have installed a second OEM set of bed lights, are you willing to part with the plug end that you are not using?

 

I assume that you are referring to the one that plugs into the box by the spare tire, not the ones that connect into the lights themselves? I ordered a second set from the dealership and just completed adding one of them to the inside of my toolbox (works very well I might add) and i don't know that I have a reason to keep the other end and could possibly part with it

 

 

Picture of the added light for those who may want to know what it looks like

photo 8.1

photo 8.2

 

  • 2 weeks later...
Trailbreaker77 Enthusiast

Trailbreaker77

Posted
Posted

I've seen posts where people have gotten this for around $50 shipped. Are those deals still around?

 

Just brought home a 2015 - 2500 Silverado and the dealer told me to do this myself and it would be easy as the holes for the installation are already there.

 

Is that true?

Mike1220 Senior Enthusiast

Mike1220

Posted
Posted

I've seen posts where people have gotten this for around $50 shipped. Are those deals still around?

 

Just brought home a 2015 - 2500 Silverado and the dealer told me to do this myself and it would be easy as the holes for the installation are already there.

 

Is that true?

Yes. Installation is very easy. You will have to search around for a deal. Some ppl found them for very cheap on eBay/Amazon. All about how much you are willing to look for it.

 

As I said, install is very easy. You will take off the tail lights to have access to wear you will run the wires and then plug in under the bed behind spare wheel. Install should only take about 1-1.5 hours.

Trailbreaker77 Enthusiast

Trailbreaker77

Posted
Posted

Yes. Installation is very easy. You will have to search around for a deal. Some ppl found them for very cheap on eBay/Amazon. All about how much you are willing to look for it.

 

As I said, install is very easy. You will take off the tail lights to have access to wear you will run the wires and then plug in under the bed behind spare wheel. Install should only take about 1-1.5 hours.

 

Well the dealer told me if I had ordered it and had the factory install it, it would have only cost me $60. I was hoping to get it at that price or less.

Civerus Enthusiast

Civerus

Posted
Posted

Alright, I've installed hundreds of these on the trucks (yay PDI's). I'm not going to read through all 13 pages to see if this has been solved so here it is.

 

The kit comes with the harness, two lights, the push-square deals and the screws. Should take about 20-30 minutes to do this.

 

1. - First lower your gate and take the tail-lights off by loosening the two screws on each one and pull them out (may take a little effort due to retaining clips)

 

2. - Next go under your bed, under the truck. Look at your spare tire. LOOK AT IT. Now look above it, to the driver side of the truck, about mid-way down the spare tire (no need to remove it), you should see a wiring BUS system, likely with quite a few things plugged into it. Look for a white dummy plug on the very driver-side of the BUS system. Remove this dummy-plug, this is where your harness will connect to.

 

3. - Goto the harness. Pick it up. Observe it, and its plastic...ey? goodness. It will be labeled DRIVER and PASSENGER side on the ends. Make sure you get this right. Go under the truck again, and plug this into the spot that you removed the dummy-plug from.

 

4. - Now take the wiring, and run the DRIVER side, as high as possible against the bottom of the bed, through all the little holes and areas to keep it held up, and run it up to a little hole that is located below the driver side tail-light. Fish this wire out of the hole and then do the PASSENGER side, the same way, above the spare tire, the crank bar, all of it, to the hole, and fish it out.

 

5. - Alright, you are done down there until the end. Now go up top and take the wire (either side) that you fished up through the tail-light hole, and now (small hands help) fish it even higher through the side of the top of the bed. This can be hard, but do-able. Do this for both sides.

 

6. - You will see some square open holes on the bed side near the side rail right below it, about a foot or two in from the back. Push the metal tabs into those two squares on each side.

 

7. - Get the LED light and place it up to the squares, facing so they would shine down preferably. Now -start- the screws through the LED light and begin screwing them in. About 4 turns in, take the wire on the driver side only, and run it ABOVE the light, BEFORE you tighten it down all the way. Finish tightening. The PASSENGER side does not have this issue.

 

8. - Once done with mounting and plugging in the LED lights, test them with the bed light switch on the dash. Works? yay +1 and get a beer. Now take the push-tabs that came on the harness and find the closest spot they push into, and do this, especially in the tail-light area.

 

9. - Reinstall tail-lights.

  • Like 1
2017SierraSLT Senior Enthusiast

2017SierraSLT

Posted
Posted

I've seen posts where people have gotten this for around $50 shipped. Are those deals still around?

 

Just brought home a 2015 - 2500 Silverado and the dealer told me to do this myself and it would be easy as the holes for the installation are already there.

 

Is that true?

 

 

Yup. Here's one:

 

 

 

http://www.ebay.com/itm/Cargo-lamp-kit-for-a-GMC-Chevrolet-Brand-new-in-box-Part-20979073-/251693433454?pt=Motors_Car_Truck_Parts_Accessories&hash=item3a9a19026e&vxp=mtr#ht_22wt_1362

Mike1220 Senior Enthusiast

Mike1220

Posted
Posted

How is that part number different from GM part# 23145347?

I think there are slight color variations.

2017SierraSLT Senior Enthusiast

2017SierraSLT

Posted
Posted

If there are variations between the part numbers, it shouldn't be an issue if one is running only the rear pair. If you want 4 total lights, then I would purchase two kits with the same part number. The kits appear identical when it comes to what hardware and harness are included and the external appearance of the light assemblies.

BWEISS57 New Member

BWEISS57

Posted
Posted

For those of you who have installed a 2nd set, how did you attach them? Did you drill into the bed or did you use something like 3M VHB tape? Thanks!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,972
    Total Members
    8,960
    Most Online
    Whit.the.COB
    Newest Member
    Whit.the.COB
    Joined

  • Who's Online   1 Member, 0 Anonymous, 602 Guests (See full list)

  • Latest Articles

  • Posts

    • Jsdirt
      What did you do to your "other" car (aka musclecar) today

      By Jsdirt · Posted

      Even tougher is the 5.0 / 302. That's what this one has.    https://postimg.cc/Z9XRrCSg   https://postimg.cc/4n3F3yzY   Just realized I had the airbox removed in the engine pic, lol.
    • MikeBMW
      Installing tow mirrors

      By MikeBMW · Posted

      Yep! This should be a pin somewhere as @pgamboa really dives into all of this. Thanks for reposting the link!
    • Grumpy Bear
      TCM Tuning 6L80E

      By Grumpy Bear · Posted

      I did the new thermostat after doing a 'flip' for a year. Runs as cool one way as the other in the summer but in the winter there is a bit of a floor. Yellow with the new 70 C thermostat. My data over the life of the unit to date. Still need more cooler. Anyway that floor helped both winter fuel economy and shift quality in the winter. I found it a good balance.       
    • Grumpy Bear
      Food & Drink

      By Grumpy Bear · Posted

      Evan Williams Bottled in Bond   So pouring the last of a bottle of Evan Williams Black label last night I set off the the state store for a refill only to be denied the by an empty shelf. Rats.    What the did have was a bottle of Evan Williams Bottled in Bond. 100 proof. Hum, a few bucks more but a known distiller. Lets have a swing at it. ( I have before )    Cracked it open and pour a serving over ice. Hum.... more heat, yes. More alcohol naturally. But the barreling not the proof brings the taste and this one came up short.    Oh is was familiar but the heat ran the barrel over like a Peterbilt runs over a squirrel. Could use a heavier toasting of the oak me thinks or perhaps a longer barreling. Who knows. But what I can say is ice or a water back isn't the answer. What kills one kills them both. Sad. It is a pleasant drink....if you have little to compare it to.  
    • Grumpy Bear
      Bridgestone vs Goodyear tires?

      By Grumpy Bear · Posted

      I've had exactly one set of Bridgestone. Lasted five year and 125,000 miles and had I known better 15oK would have been a cake walk. I would have bought a like set had they not tripled in price since the first set. I removed them at said mileage with 5/32" remaining in dead even wear all four. They were fuel efficient, quite, comfortable and predictable.    Early on I got a very good alignment checked at least once a year, sometimes twice; kept the tires properly inflated, balanced and rotated. And I've found that many a tire issue can be avoided with great maintenance practices. Lot's of tire dealers will do rotation and balance (simple) for free for as long as you own the tire they sold you so no excuse not to.    Bead prep, alloy integrity and stem health have a huge impact on inflation stability. There are more mountings done poorly that perfectly. Finding a good tire guy is gold and as important as finding a tire you like.    That 3X price increase now two sets of "other tires' later is starting look like a bargain.      Bad maintenance kills more tires than bad tires. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...