Jump to content

Radar Detector Install

clayp

By clayp
in Modifications & Accessories

 Share

Recommended Posts

clayp Enthusiast

clayp

Posted
Posted (edited)

This is for the 2014 Sierra/Silverado 1500

 

Ok I decided to hardwire my Valentine 1. The install should work for any detector. Others have noted that they could not find a 12v lead off the rear view mirror, so I tried the overhead console.

 

The console (I have Homelink) pops off very easily. You open the sunglass compartment halfway and you can pry open the edge of the console with just your fingers. You should now see this:

 

photoa_zps881715fc.jpg

 

There are three connectors to the console panel: 1 at the front (small black) is for the Homelink buttons, the middle connector (black) is for the LED ambient light, the rear one (brown) is for the interior light switch for the doors.

 

photob_zpse2d8448c.jpg

 

I tested all three connectors and could only find a good 12v + and - at the rear connector for the interior light switch. The left most yellow wire is 12v + and the right most black is - . The yellow wire is triggered with door opening and stays on until all accessory power shuts off. When you lock the car it shuts quickly, otherwise is remains on for maybe 20 sec

 

I used vampire taps and wired in the Valentine harness. The cord to the detector easily wedges thru the front of the console out to the area around the rear view mirror. There is also tons of room to stow away any wiring up there.

 

All tapped in and powered right up:

 

photo_zps42a9cc0b.jpg

 

For tools, the connectors need a small screwdriver to release the clips, and otherwise the only other thing required is taps and a voltmeter. Takes 30 min max

Edited by clayp
  • Like 2
  • Replies 86
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

clayp
clayp

Well disregard the previous post - as is the radar detector will not work in the daytime lol! It only works when the nighttime ambient light is triggered.   Back to the drawing board. I removed the

rdtpp1991
rdtpp1991

I installed the Blendmount and MirrorTap for my V1 tonight...took about 15 mins. If you have powered OnStar mirror and no lane departure it is really easy. There is a harness in cover that goes from

TXTruk15
TXTruk15

you should be able to pop off the whole cover, not just the #2 part, that will get you to the plug easier....   check this out...about 35 seconds into the video....  

Posted Images

clayp Enthusiast

clayp

Posted
  • Author
Posted

Well disregard the previous post - as is the radar detector will not work in the daytime lol! It only works when the nighttime ambient light is triggered.

 

Back to the drawing board. I removed the old setup and this time removed the entire overhead console - not just the panel. There are two T10 screws to remove:

photoc_zps47004e04.jpg

 

Then there are two friction fit tabs up front that just pull straight down.

photoe_zpsae21bf9b.jpg

 

There is a main wiring harness to the overhead console on the left side that you can disconnect.

photod_zps8daa614c.jpg

 

Testing all the wiring shows that the black wire is a good ground, and the leftmost purple wire with white stripe is a good 12v positve that directly is triggered by the ignition. Engine on, power on; engine off, power off.

photof_zps8e5450cb.jpg

photog_zpse3882599.jpg

 

Just an extra step but now all seems to work properly. I think the purple wire with white stripe is the power lead to the passenger airbag light on the overhead console.

  • Like 5
  • 3 weeks later...
jcchevy Enthusiast

jcchevy

Posted
Posted

Very nice write up. I plan on picking up a V1 later down the road as well. I see it retails for $399, did you find it cheaper and if so can you provide the link/store source? Thanks man.

MikeNH Senior Enthusiast

MikeNH

Posted
Posted
Very nice write up. I plan on picking up a V1 later down the road as well. I see it retails for $399, did you find it cheaper and if so can you provide the link/store source? Thanks man.

 

 

Unless you do as Won suggested you won't find a better price unless you buy used. Not sure you can get them anywhere but the manufacturer. If you live near them (Cincinnati I think) you can even pick it up in person, or at least you used to be able to.

  • 1 month later...
SSLS2TB Enthusiast

SSLS2TB

Posted
Posted

Excellent write up. Seeing how to remove that console was priceless. This helped me tremendously. :cheers:

Rkparker Enthusiast

Rkparker

Posted
Posted

I was able to get ignition on/off 12v at the mirror harness with the purple and green wire. Black was still ground. If using mirror tap I would get 15" with nano width for pin.

bigsapper Enthusiast

bigsapper

Posted
Posted (edited)

Do you have a pic of your console? I have the regular cab and it didn't come with Homelink. I'm thinking I should be able to get the panel with the homelink buttons and be GTG, right?

 

Nevermind. There is no wiring run for the Homelink.

Edited by bigsapper
JAF1 Enthusiast

JAF1

Posted
Posted

Has anyone tried running a wire along the headliner, down the A pillar then into the fuse box? That's the way I had my last one wired but I didn't have an airbag in the pillar to worry about.

ctostrowski Enthusiast

ctostrowski

Posted
Posted

Has anyone tried running a wire along the headliner, down the A pillar then into the fuse box? That's the way I had my last one wired but I didn't have an airbag in the pillar to worry about.

yes I did no issues.

JAF1 Enthusiast

JAF1

Posted
Posted

yes I did no issues.

 

Did you pop off the cover or were you able to just tuck in?

ctostrowski Enthusiast

ctostrowski

Posted
Posted

 

Did you pop off the cover or were you able to just tuck in?

I followed the headliner tucked it in the arm and then next to the door gasket. I never removed any of the plastic covering

KUUG Enthusiast

KUUG

Posted
Posted (edited)

This can also be done through an auto dimming mirror with a lot less work. Thats the way I did mine anyway

Edited by KUUG
sh00ter Enthusiast

sh00ter

Posted
Posted

I had planned on hooking up my Valentine One using an Invisicord as I have on lots of past vehicles. It just connects to the plug on the rear of the auto dimming mirror. But, my Denali has the Lane Departure Warning option & there is a box in front of the mirror that houses the cameras it uses. There is no plug to tap into.

 

Has anyone done this hard wire hookup on a truck with the Lane Departure Warning? If so, does it work the same way?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • 81mmcat
      Higher oil pressure after DFM shut off

      By 81mmcat · Posted

      Can anyone explain why the oil pressure runs higher after the DFM is shut off?  just installed the Pulsar Lt.
    • fm2176
      New to Me 2010 SLE (Quirks, Issues)

      By fm2176 · Posted

      Thanks!  I figured as such; GM and other manufacturers have used standard parts and harnesses across trim levels and such for decades.  I pulled the blank accessory cover off of my commuter van (a 2016 or so Chevy 15-passenger) years ago and found the plug for a USB outlet.  It wasn't connected to anything, though (I tried swapping in an outlet from another van).  I was a GM Tech years ago (late-90s) and was pretty familiar with my 2006.  I might be wrong, but I view newer vehicles (pretty much anything made in the past 20 years) as being a lot more plug and play.  Meaning, more unused wires and plugs unless you have the Mack Daddy of vehicles.    
    • Coastie05
      It's Been a Long Time...

      By Coastie05 · Posted

      Welcome back!
    • davester
      New to Me 2010 SLE (Quirks, Issues)

      By davester · Posted

      not all plugs will be used.  gm uses more generic harnesses that support most/all options, and if your truck doesn't have a specfiic option, the plug won't be used (commonly will have a dummy insert in the plug , or it'll be taped up, but some may just be left as is).  But it's sldo possible some p.o. has installed the wrong/cheaper parts that aren't correct for your vehicle...
    • fm2176
      New to Me 2010 SLE (Quirks, Issues)

      By fm2176 · Posted

      First off, I'm not trying to just get easy advice/fixes for the issues I've noticed so far.  I'll be combing through the site via searches and such, and if past experiences are any indication, should find what I need.  For the sake of conversation, though, I figured I'd post the handful of things I've noticed in the 12 hours since buying my 2010 SLE CCSB.     Indicator lights: Airbag and TPMS.  The tire pressures aren't reading for any of the wheels, so I'm pretty certain the sensors were either removed, are damaged, or are otherwise inoperable.  I used to mount and balance tires 25 years ago but am pretty much ignorant when it comes to TPMS.  My 2006 didn't have the sensors and this might be the fourth vehicle I've owned that does.     Radio: Rear speakers aren't working.  I removed the driver's side rear door panel and checked the speaker and wiring.  I also removed the sill and b-pillar covers to check the wiring.  A few minutes of Google Fu showed that this is potentially a head unit issue.    Switches: Power mirrors don't turn left/right.  I ordered replacement driver's door switches that should arrive tomorrow.  The windows and locks work but it was only about $20 for all of them.  The driver's side rear window switch lets the window down but won't put it back up.  I think the passenger rear doesn't work at all.  In the coming days/weeks, I'll break out my multimeter to check all of that.   Unknown wiring harness: There's a box attached to the front driver's side of the engine compartment, right where the second battery shelf is located.  There are three plugs, one of which looks like it fits a standard headlight-style bulb (9007 or similar).  It doesn't look like it's plugged into anything.  I'll do some digging and if I don't see anything elsewhere on the site, post some pictures here.   Unknown plugs on brake booster: There are at least two female plugs on the brake booster that aren't being used.  I think it might be a replacement/aftermarket, so maybe those are used for a different application, as there don't seem to be any unplugged harnesses and no indicator lights are on.   Little squeaks when turning: Sounds almost like a bushing around the bed of the truck.  I'll have to pay close attention as I get more familiar with the truck.   Clunk on acceleration: possibly the infamous drivetrain clunk.  My 2006 had it and I'm just not familiar enough with this truck yet to fully grasp what it is.   Anyway, my apologies for the vague and all over the place post.  This truck is new to me, and it's been four years since I drove my 2006.  With 200k miles, I know I'll need to learn this truck quickly to avoid having any major issues, despite being confident it's got much more life to it.  My 2006 had nearly 320k on it when I parked it (nearly 300k of which I put on the truck), and it was still drivable then, though I suspected the head gasket might have blown.  I'd hoped to have that truck back by now, but it's gone forever, as I detailed in my reintroduction thread.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...