Jump to content

Center console swap?

quickvert1

By quickvert1
in Modifications & Accessories

 Share

Recommended Posts

1911-A1 Enthusiast

1911-A1

Posted
Posted (edited)

AgDocktor: looks like there are two screws on top also.Check this thread it might help or the OP might be able to answer your question

3 coil wireless charger install in 2015 Sierra Denali

Edited by 1911-A1
  • Replies 1.9k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

darkfox1
darkfox1

OK.. mine's in.   Here's a writeup, cos I haven't seen one so far.   1. remove the "ash tray" and cig. ligther in your dash with 3 t-10 torx screws, and 2 clips. 2. Remove the radio trim, clips i

dla
dla

I always wanted a RCSB with buckets and a center console...   Received and installed mine yesterday. Very straight forward, thanks for all who posted instructions and part numbers.   Possibly to h

o7bodybagged
o7bodybagged

Finally the console is complete now ready for the install and see what other problems I run into

Posted Images

AgDoctor Senior Enthusiast

AgDoctor

Posted
Posted

AgDocktor: looks like there are two screws on top also.Check this thread it might help or the OP might be able to answer your question

3 coil wireless charger install in 2015 Sierra Denali

Thanks for that! I really appreciate the link. I will keep you guys posted on my progress.

 

Sent from my SM-N910V using Tapatalk

DonkeyKiller Enthusiast

DonkeyKiller

Posted
Posted

Hey guy just got my console in and wanted to say thanks for all the help from the forum. Getting the jump seat out was much harder than I thought but getting the new console put in was much easier than expected. I only used two bolts where the bracket mounts to the dash so that I didnt have to take any of the dash apart and the console is in there solid. I love how much storage room this thing has.

 

IMG 20160107 153920

IMG 20160107 154055

nolabell Enthusiast

nolabell

Posted
Posted

Hey guy just got my console in and wanted to say thanks for all the help from the forum. Getting the jump seat out was much harder than I thought but getting the new console put in was much easier than expected. I only used two bolts where the bracket mounts to the dash so that I didnt have to take any of the dash apart and the console is in there solid. I love how much storage room this thing has.

 

 

Nice, I bought all my console parts, just waiting for free time to do the install. Did you get the front three USB'c to charge?

kchiasson64 Enthusiast

kchiasson64

Posted
Posted

Hey guys I just got my console in, started on it this morning at 9 and I'm wrapping it up at 1:30. Also I have the front 3 USB playing music and charging and I have all 4 cig outlets working and the interior led for the console is wired to my cab lights. Everything went smoothe and I want to thank everyone for the info and insight on the process. I absolutely love this thing. 108199a698f66c4b54c195c18b41d04e.jpg8420513fc28eaa0c4b9cd983d49f2585.jpg0d3bbf23485c65d7b14d688a4bfce04a.jpg

 

 

iPhone 6 '14 Silverado

nolabell Enthusiast

nolabell

Posted
Posted

Hey guys I just got my console in, started on it this morning at 9 and I'm wrapping it up at 1:30. Also I have the front 3 USB playing music and charging and I have all 4 cig outlets working and the interior led for the console is wired to my cab lights. Everything went smoothe and I want to thank everyone for the info and insight on the process. I absolutely love this thing. 108199a698f66c4b54c195c18b41d04e.jpg8420513fc28eaa0c4b9cd983d49f2585.jpg0d3bbf23485c65d7b14d688a4bfce04a.jpg

 

 

iPhone 6 '14 Silverado

 

That's awesome Keith!! How did you tap into the lights to get the LED to work? Is that the blue wires in the picture, underneath the console? Also as far as the charging USB's up front: did you use the AC Delco USB male to male connection; one side into the back of the chargers and the other into the HMI?

jchildress Enthusiast

jchildress

Posted
Posted

Hi Guys. I've read till my eyes are crossed so I'll just see if you guys can help. I'm thinking about buying a 2014 GMC Sierra 1500 All Terrain. Currently, it has a fixed center console. However, I have a bunch of kids so I need the flip up console. If I buy this truck, will I be able to buy a jump seat to put it its place? Will it bolt up easily and wire easily? Looks like most people are getting rid of the jump seat in favor of the center console.

 

Also, anybody on here happen to have a black leather one they need to get rid of?

 

Thanks so much for any help. Need to buy pretty soon.

  • Like 1
kchiasson64 Enthusiast

kchiasson64

Posted
Posted

For the led light, I took the pigtail and unplugged it from the led. Then I followed the wire down about 4 inches and cut it and taped off the dead ends. From there I took the plug with now bare ends and spliced them and butt connected it to the 2 blue wire you see. One marked negative the other is white it's the positive.

 

 

iPhone 6 '14 Silverado

kchiasson64 Enthusiast

kchiasson64

Posted
Posted

As far as getting everything up front to work I removed the entire jump seat harness from the jump seat. I then plugged the harness back into the floor plugs under the passenger seat. I used all of the connections up front and that's all.

 

 

iPhone 6 '14 Silverado

nolabell Enthusiast

nolabell

Posted
Posted

Hi Guys. I've read till my eyes are crossed so I'll just see if you guys can help. I'm thinking about buying a 2014 GMC Sierra 1500 All Terrain. Currently, it has a fixed center console. However, I have a bunch of kids so I need the flip up console. If I buy this truck, will I be able to buy a jump seat to put it its place? Will it bolt up easily and wire easily? Looks like most people are getting rid of the jump seat in favor of the center console.

 

Also, anybody on here happen to have a black leather one they need to get rid of?

 

Thanks so much for any help. Need to buy pretty soon.

 

Yes, they should be interchangeable. Where are you located? I have a black leather center jump seat that I will be removing soon and selling.

nolabell Enthusiast

nolabell

Posted
Posted (edited)

For the led light, I took the pigtail and unplugged it from the led. Then I followed the wire down about 4 inches and cut it and taped off the dead ends. From there I took the plug with now bare ends and spliced them and butt connected it to the 2 blue wire you see. One marked negative the other is white it's the positive.


iPhone 6 '14 Silverado

 

The pigtail of the console LED?

Edited by nolabell
jchildress Enthusiast

jchildress

Posted
Posted

 

Yes, they should be interchangeable. Where are you located? I have a black leather center jump seat that I will be removing soon and selling.

 

I'm in SWVA. Close to the VA TN line. Wonder if the color would be the same. Looks jet black to me (leather). Not 100% sure this will be happening, but it might.

nolabell Enthusiast

nolabell

Posted
Posted (edited)

 

I'm in SWVA. Close to the VA TN line. Wonder if the color would be the same. Looks jet black to me (leather). Not 100% sure this will be happening, but it might.

 

I think they are the same, black leather with white stitching. We are pretty far, I am New Orleans, 8-9 hour drive away

Edited by nolabell
kchiasson64 Enthusiast

kchiasson64

Posted
Posted

Yes the console led I left about 4 or 5 inches of wire on it then plugged it back into the led

 

 

iPhone 6 '14 Silverado

Hey what part of Nola you in? I'm in marrero

 

 

iPhone 6 '14 Silverado

nolabell Enthusiast

nolabell

Posted
Posted

Yes the console led I left about 4 or 5 inches of wire on it then plugged it back into the led

 

 

iPhone 6 '14 Silverado

Hey what part of Nola you in? I'm in marrero

 

 

iPhone 6 '14 Silverado

 

Wow, I actually work in Algiers and live in Metairie. Small world, might have to summon you for some help with the install lol. Do you have a 2014 or 2015?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,972
    Total Members
    8,960
    Most Online
    Whit.the.COB
    Newest Member
    Whit.the.COB
    Joined

  • Who's Online   0 Members, 0 Anonymous, 526 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • Jsdirt
      What did you do to your "other" car (aka musclecar) today

      By Jsdirt · Posted

      Even tougher is the 5.0 / 302. That's what this one has.    https://postimg.cc/Z9XRrCSg   https://postimg.cc/4n3F3yzY   Just realized I had the airbox removed in the engine pic, lol.
    • MikeBMW
      Installing tow mirrors

      By MikeBMW · Posted

      Yep! This should be a pin somewhere as @pgamboa really dives into all of this. Thanks for reposting the link!
    • Grumpy Bear
      TCM Tuning 6L80E

      By Grumpy Bear · Posted

      I did the new thermostat after doing a 'flip' for a year. Runs as cool one way as the other in the summer but in the winter there is a bit of a floor. Yellow with the new 70 C thermostat. My data over the life of the unit to date. Still need more cooler. Anyway that floor helped both winter fuel economy and shift quality in the winter. I found it a good balance.       
    • Grumpy Bear
      Food & Drink

      By Grumpy Bear · Posted

      Evan Williams Bottled in Bond   So pouring the last of a bottle of Evan Williams Black label last night I set off the the state store for a refill only to be denied the by an empty shelf. Rats.    What the did have was a bottle of Evan Williams Bottled in Bond. 100 proof. Hum, a few bucks more but a known distiller. Lets have a swing at it. ( I have before )    Cracked it open and pour a serving over ice. Hum.... more heat, yes. More alcohol naturally. But the barreling not the proof brings the taste and this one came up short.    Oh is was familiar but the heat ran the barrel over like a Peterbilt runs over a squirrel. Could use a heavier toasting of the oak me thinks or perhaps a longer barreling. Who knows. But what I can say is ice or a water back isn't the answer. What kills one kills them both. Sad. It is a pleasant drink....if you have little to compare it to.  
    • Grumpy Bear
      Bridgestone vs Goodyear tires?

      By Grumpy Bear · Posted

      I've had exactly one set of Bridgestone. Lasted five year and 125,000 miles and had I known better 15oK would have been a cake walk. I would have bought a like set had they not tripled in price since the first set. I removed them at said mileage with 5/32" remaining in dead even wear all four. They were fuel efficient, quite, comfortable and predictable.    Early on I got a very good alignment checked at least once a year, sometimes twice; kept the tires properly inflated, balanced and rotated. And I've found that many a tire issue can be avoided with great maintenance practices. Lot's of tire dealers will do rotation and balance (simple) for free for as long as you own the tire they sold you so no excuse not to.    Bead prep, alloy integrity and stem health have a huge impact on inflation stability. There are more mountings done poorly that perfectly. Finding a good tire guy is gold and as important as finding a tire you like.    That 3X price increase now two sets of "other tires' later is starting look like a bargain.      Bad maintenance kills more tires than bad tires. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...