Jump to content

Recommended Posts

Posted

I would like to document in one thread the solutions/fixes to vibration vs sifting and reading through 6000 posts. Please stay on topic.

 

Please state

 

Year 2014/2015

Make, Chevy or GMC

Cab, Crew, Double, Single

Box, 5.5, 6.5 or 8ft

Engine V-6 5.3 or 6.2

Transmission 6 or 8 speed

Rear Gear. 3.08, 3.23 3.42 or 3.73

Speeds the vibrations are present

Solutions:

 

2014

GMC Sierra SLT

Crew

6.5 Box

6.2L

6 Speed

3.73

70mph +

 

Solution

 

The things that have made mine better. Replaced one wheel, two LS2 20" Goodyears and Road Force Balance. Still not 100% fixed.

 

  • Like 1
Posted (edited)

Chevy. 5.3 CC Short bed 4x4 z71 3.08 6 speed. It was a 70mph+

 

98% fixed by multiple sets of tires and RF balancing. Now i only notice a tiny tiny vibe after long 80mph drives. I have to be looking for it and even then it may be road noise.....

Edited by afireinside7444
  • Like 1
  • 4 weeks later...
Posted (edited)

I would like to document in one thread the solutions/fixes to vibration vs sifting and reading through 6000 posts. Please stay on topic.

 

Please state

 

Year 2014/2015

Make, Chevy or GMC

Cab, Crew, Double, Single

Box, 5.5, 6.5 or 8ft

Engine V-6 5.3 or 6.2

Transmission 6 or 8 speed

Rear Gear. 3.08, 3.23 3.42 or 3.73

Speeds the vibrations are present

Solutions:

 

2014

GMC Sierra SLT

Crew

6.5 Box

6.2L

6 Speed

3.73

70mph +

 

Solution

 

The things that have made mine better. Replaced one wheel, two LS2 20" Goodyears and Road Force Balance. Still not 100% fixed.

 

 

As of 10/8/2015 my local dealer and GM engineering replaced both rear shocks. 4 Goodyear LS2 tires and rebuilt the rear differential with new ring and pinion and bearings. They ran the truck with the pico meter and it was within spec.

 

I drove the truck and the vibration seemed to be gone. The thing I notice now is that on poorer quality roads the truck picks up a lot of road vibration. On the smooth, quality roads the truck drives smooth and great. Even while going up to 80mph.

 

I can't call it 100% fixed because from time to time I swear I feel a vibration. I can't tell if it is the truck or the road 100%.

 

So lets call it 98% fixed just to be safe. It certainly is fixed enough where it is not longer unpleasant to drive the truck.

 

Hopefully this helps someone else. Good luck getting your vibration in your GM truck fixed!

Edited by OmahaBen
  • Like 1
Posted

Year 2014

Make, Chevy

Cab, Double

Box, 6.5

Engine 5.3

Transmission 6 speed

Rear Gear. 3.42

Speeds the vibrations are present: about 40 mph to 60 mph; more noticeable when decelerating

Solutions: I noticed the viberation around 7000 - 9000 miles. at 18000 the dealer said 3 of the 4 goodyear sra's were out of round and I replaced the tires with 275/60R18 Michelin LTX at's (The truck has a 1.5" leveling kit). They didnt ballance them correctly the first time at the dealer so after having a tire shop ballance them the vibration was 65% better and only noticeable between 45-50 mph. I thought this was much more liveable. Now at 26000 miles, im noticing the vibration is back to the 40 mph to 60 mph range again.

Posted

Year 2014

Make, Chevy

Cab, Double

Box, 6.5

Engine 5.3

Transmission 6 speed

Rear Gear. 3.42

Speeds the vibrations are present: about 40 mph to 60 mph; more noticeable when decelerating

Solutions: I noticed the viberation around 7000 - 9000 miles. at 18000 the dealer said 3 of the 4 goodyear sra's were out of round and I replaced the tires with 275/60R18 Michelin LTX at's (The truck has a 1.5" leveling kit). They didnt ballance them correctly the first time at the dealer so after having a tire shop ballance them the vibration was 65% better and only noticeable between 45-50 mph. I thought this was much more liveable. Now at 26000 miles, im noticing the vibration is back to the 40 mph to 60 mph range again.

Yeah....the problems not the tires....
Posted

2014

Chevy

Crew Cab

5.3 6 speed

3.42

20" wheels

Vibration over 74mph...Balanced Tires 4 times, road forced tires once, still vibrated. Took tires and wheels off of brand new truck off the dealer lot, still vibrated, put my tires on the new truck, didn't vibrate according to the dealer. New drive shaft, still vibrated.

Now have 43,000 miles on it and have given up. About to buy new tires because the stock goodyears are about wore out hoping new tires will help a bit. I only have to deal with it for another 18 months then I get a new vehicle.

  • 1 year later...
Posted

I have a 2016 Chevrolet Silverado 1500 WT 4x4 8 foot bed.At 65+ mph the vibration is stronger.Had it looked at twice by the dealership I purchased at.All they did is road force balance both times with no change to my truck.Contacted the dealership for a third time and made an appointment.Service manager stated he would have my truck picked up and leave me with a rental.This appointment has came and gone today (4-4-17.Called this morning to confirm and the service manager was out sick and nobody was aware of this appointment.Was told I would get called back and nothing!So frustrated with this whole thing.Has 6500 miles on it now.I Have been a loyal GM consumer as long as I can remember.Starting to rethink this loyalty and passion I always had for GM.

Posted (edited)

2015 Chevrolet

Crew Cab

5.5' Bed

5.3L

6-Speed

3.42

70+ mph

 

Solutions: Driveshaft rebalanced, roadforced balanced all 4 tires, & front end alignment by independent shops. Better but still there.

Replaced both rear axles shafts with Yukon Gear axles, vibration free since

Edited by MRW412
  • Like 4
Posted

That's awesome.Thank you for heads up.Just beyond frustrated with GM.Would kill me to spend my morney after giving them $43,000 already!

  • 4 months later...
Posted

2015 Chevrolet

Crew Cab

5.5' Bed

5.3L

6-Speed

3.42

70+ mph

 

Solutions: Driveshaft rebalanced, roadforced balanced all 4 tires, & front end alignment by independent shops. Better but still there.

Replaced both rear axles shafts with Yukon Gear axles, vibration free since

I`am getting ready to pull the trigger on the Yukons did you replace the bearings to?

Posted

No, I didn't replace the bearings. They seemed fine when I was inspecting them. I did replace the seals though. Does yours have the rear end shake? My shake was coming from rear end and I never felt in the steering wheel.

Posted

I have a 2016 Chevrolet Silverado 1500 WT 4x4 8 foot bed.At 65+ mph the vibration is stronger.Had it looked at twice by the dealership I purchased at.All they did is road force balance both times with no change to my truck.Contacted the dealership for a third time and made an appointment.Service manager stated he would have my truck picked up and leave me with a rental.This appointment has came and gone today (4-4-17.Called this morning to confirm and the service manager was out sick and nobody was aware of this appointment.Was told I would get called back and nothing!So frustrated with this whole thing.Has 6500 miles on it now.I Have been a loyal GM consumer as long as I can remember.Starting to rethink this loyalty and passion I always had for GM.

Sounds like a problem with an individual not the brand. Welcome to the forum and good luck with your truck. I have been a GM fan for many years and have never experienced this vibration issue on a new truck. Some of my older vehicles have had vibration at higher speeds but always fixed with tires & balance. It wasn't too long ago when 8 ft. box's were the most common sight. Now they stand out. Any pics?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,958
    Total Members
    8,960
    Most Online
    B07
    Newest Member
    B07
    Joined
  • Who's Online   0 Members, 0 Anonymous, 793 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • Missing pieces of the Assembly   Detergency vs Solvency   Not the same thing. Detergency is the mechanism that surrounds solid particulates preventing amalgamation. Usually accompanied by a Dispersant whose job it is to keep those encapsulated particles in Suspension. Solvency keeps things that can be dissolved in solution.    Salt is a solid that can be dissolved. Pepper is a solid that cannot be dissolved. A detergent/dispersant is effective on pepper but a solvent is more effective on salt. As long as the solids remain in either state, dissolved or dispersed then they can be be removed with the oil upon change.    How many wranglers does it take to herd cats? Depends on how many cats your herding. How much sponge does it take to soak up water? How much water is there to soak up? Point is most oil blends start with some herding ability and next to zero sponge and recently even fewer wranglers are being sent to do the same job.    So you start with a dozen cowboys and zero cows but at the drive progresses you pick up cows along the way, but not cowboys. At some point you have more cows that the wranglers can handle and some leave the herd. Deposits. And the API has an acceptable number of cows they are willing to let loose. In the ideal world zero is the right number for he rancher but to the butcher....a few lost is fine. This cow is beat to death. Let's move on....   Solvency isn't something oils on the Walmart shelf care about AT ALL. Problem is, you motor does. Fuels driven varnish sticks rings and only a solvent can keep them in check. The bet is that the solids driven portion that plug the expander rings and the oil drain backs and VVT screens and AFM screens will be an issue long before varnish is. Not that it wont be but if they market well enough the consumer can be kept ignorant enough to either believe it is "normal" (A quart in 1 or 2K is normal) OR is kept at bay longer than the first owner is likely to hang on to the unit. Solvency cost money.    Now the OEM's have John Q. Public buffaloed into the belief that the number cows accumulated along the trail is a known and predictable CONSTANT. It isn't. Nor is the rate at which they crossed paths with them. Only the number of wrangles is constant. Or was. Each new generation of oil sees fewer and fewer of them.    So what happens when the number of cowboys is lower (lower TBN) with each seasons trail but the trial is longer (OCI) and the number of cows along that trail continues increase? (Conditions that promote deposits).    For awhile the blenders were on to something. Better bases are harder to degrade (fewer cows) but that was overtaken by a longer trail (OCI) and improved breeding (More cows) while continuing to reduce the cowboy staffing levels (TBN/Aniline #).    Marketing has been successful. We've fired most of the staff, cows breed line bunnies, the trail is ten times longer and we've convinced the boss his ranch is in better shape that it ever was.    That kids is just the cleaning side. The side few pay attention to.     
    • Mann+Hummel since 1941 per their web site 
    • Looking for this part for my truck. They don't sell just that one piece and to get it you have to pay over $100 even used for the whole air tube. The piece the hose clamp snaps into that is held on by the screw and nut. If anyone has access to one please let me know.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...