Jump to content

Recommended Posts

Posted

Everytime i run my cooled seats it blows hot air through the back vents of the front seats. Is this normal? I cant run them when someone sits jn the back because it heats up their legs really bad.

Posted

Just wondering because my raptor blew fresh air and never noticed any hot air being blown out, maybe they routed it out through somewhere else, makes more sense than the chevys design of blowing it to the passengers sitting in the back

Posted

Can't have cold without compression and compression byproduct is heat.

 

Yes you can have cold without compression. The cooled seats use TEC elements, which work on the Peltier effect. No compression, just voltage that pulls heat in one direction across the P/N junction. And as the OP found out, the heat is expelled out the back, and rather noisily too.

 

Now, why GM thought it was a good idea to dump that heat right to the rear passengers at almost face level is beyond me.

Posted

 

Now, why GM thought it was a good idea to dump that heat right to the rear passengers at almost face level is beyond me.

 

 

No kidding.. And to add to that, they didn't put any AC vents back there for whatever reason..

Posted

 

Yes you can have cold without compression. The cooled seats use TEC elements, which work on the Peltier effect. No compression, just voltage that pulls heat in one direction across the P/N junction. And as the OP found out, the heat is expelled out the back, and rather noisily too.

 

Now, why GM thought it was a good idea to dump that heat right to the rear passengers at almost face level is beyond me.

The greatest thing for me being born ignorant is I learn something new everyday :thumbs:

Posted

 

Yes you can have cold without compression. The cooled seats use TEC elements, which work on the Peltier effect. No compression, just voltage that pulls heat in one direction across the P/N junction. And as the OP found out, the heat is expelled out the back, and rather noisily too.

 

Now, why GM thought it was a good idea to dump that heat right to the rear passengers at almost face level is beyond me.

They may work on the Peltier effect, but when assembled they all work on Pedro effect.

Posted

those are intake ports on the back side of the front seats. They do no exhaust air.

is mine backwards then?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • I have an old dental chair in my shop. Something I got for free and apparently it has more than scrap value? People collect them although mine isn't restored or anything. It's visually interesting (1930's Ritter) which is why I like it. And it IS decently comfortable if you kick back.   When a good buddy of mine saw it he said, let me guess, Atlas. It's a conversation piece? As in, you ask the questions, they do the talking?   Where do you hide the jar of teeth?   I would never.   
    • Are we talking about the same thing, though? The 7 versus 3 wear metals was from Lakespeed's 3.0-specific oil brand comparison test between AcDelco oil and Mobil ESP. The filter remains a constant so whatever excess particles the AcDelco oil is producing aren't being filtered out.   I'm assuming there's a parallel comparison to be made; IF the filter can filter down those particles, engine life increases, and your graph makes the case that a better filter (lower micron rating) can increase engine life. Introducing fewer particles AND filtering those particles with higher efficiency is the best of all worlds. Good oil, good filter.   Where we may disagree is the "baseline relative engine life". I'm more apt to believe the base engine life value is 200k+ on very average oil and filters, "bulk oil of unknown brand and white-label generic fleet-grade filter, Jiffy Lube"   Going from a 10 micron filter to a 5 micron filter should boost a base 200k to 275k in a vacuum as a single factor alone.   Here's the whatabout: How does regularly changing the oil and filter ahead of recommended schedule influence baseline engine life? Most people aren't going to science the heck out of this stuff or ask about Micron ratings, HTHS, or wear comparison tests at Jiffy Lube. Most of the Jiffy lube techs would say they need to call their tech support line to even try to get an answer.   --   Because we love anecdotes here, when I was fishing for 4.3 parts at a local yard this weekend, ALL of the 4.3 vehicles had well over 200k. I love looking at odometers of junked vehicles. How far did THIS go before landing at the crusher? The ones that still had engines weren't seized. None of them were vehicles I'd consider were Amsoil queens, in fact most of them had some kind of service cling-sticker in the corner of the windshield indicating it probably had very average maintenance services. Even the fresh parts rigs- I'm not sure taking an S/T series to 400k has much value considering the running value of those vehicles was probably somewhere around $1,000. 25+ years is a good run on time alone.   The intake manifold I salvaged had clean and bright pool areas. As expected, I found the fuel lines in the manifold rubbed through, just like mine. I'm guessing the lines on that donor truck started leaking, the truck started running rough, and its owner said that's enough I'm unwilling or can't take it out of service for several days, or spend $1000+ to repair it at a shop, it's simply time for a newer more reliable vehicle (or, more than likely, this is the 2nd, 3rd time this has happened in the truck's lifetime). While I don't count on my Blazer for reliability, the thought of giving it away for parts at certain points during my adventure, and being mentally free from its needs has has crossed my mind. I'd be losing $1500 or so, but I can only make more money; not time.
    • still $4.00 85 oct.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...