Jump to content

Recommended Posts

Posted
6 hours ago, Nasty said:

It has been like this sonce 2005 models. There is a battery current sensor on the ground cable that monitors this. 

Just came from a '07 Escalade EXT and it did NOT do this.  

 

That said, not a big deal.  Everyone keeps mentioning saving the battery or alternator wear..that's not why this is done at all.  Fuel mileage is why they do it.

  • Like 1
Posted
2 minutes ago, Nitrousbird said:

Just came from a '07 Escalade EXT and it did NOT do this.  

 

That said, not a big deal.  Everyone keeps mentioning saving the battery or alternator wear..that's not why this is done at all.  Fuel mileage is why they do it.

It does have it.  Youll see a loop around your ground cable by the battery.    But yes  its all for 1 mpg

  • 9 months later...
  • 1 year later...
Posted

is there a way to disable this feature? I have an inverter with it's own battery hooked up with an isolation switch that depends on having the alternator work at all times.

  • 4 months later...
Posted

Sorry guys. I undersand what you are saying but my 2015 Chevy Silverado 1500 pickup truck didn't start doing this until 33,000 miles. If what you are all saying is true, it should have been doing this all along, which it didn't.

Posted

Sorry guys. I undersand what you are saying but my 2015 Chevy Silverado 1500 pickup truck didn't start doing this until 33,000 miles. If what you are all saying is true, it should have been doing this all along, which it didn't.

Posted (edited)

Just because you don't recall seeing it doing this before is no proof it never happened.  Can't keep your eye's of the road all the time..whats more if you are making a lot of short trips it may not go into fuel economy mode as often as some who drives long distance.

 


 

Quote

 

Voltmeter Fluctuation

Some customers may comment that the volt gauge fluctuates between 12 and 14 volts on their 2005-08 full size pickup or utility vehicle. Starting with the 2005 model year, these vehicles are equipped with a Regulated Voltage Control (RVC) system. RVC reduces the targeted output voltage to 12.6-13.1 volts when in Fuel Economy Mode to improve fuel economy.

The generator may exit Fuel Economy Mode if additional voltage is required. This causes the voltmeter to fluctuate between 12 and 14 volts (fig. 16), as opposed to non-regulated systems which usually maintain a more consistent reading of 14 volts.

 

This fluctuation with the RVC system is normal system operation. No repairs should be attempted. Refer to the owner manual Section 3 (Instrument Panel) Voltmeter Gage for more information.

TIP: Refer to PIT4426 for concerns with keeping a camper or trailer battery properly charged.

 

 

Edited by elcamino
Posted

The only time I really notice the voltage gauge approaching 12V is when it's warm outside. I believe the computer also factors ambient temp into how much or little voltage is applied by the alternator. If you look at any charts for charging lead acid batteries, as temp goes down, voltage goes up. In the winter time I rarely seem anything lower then about 13.5 volts.

  • 3 weeks later...
Posted

Thank you everyone for enlightening me on how the RVC system works. I have a 2006 GMC Sierra whose alternator Ive been worrying about. My concern started when I noticed my headlights and dash lights flickering. I watched the voltmeter and noticed some fluctuations also. I assumed the two issues were connected. Maybe they are and maybe they aren't. I recently purchased and installed a digital voltmeter/USB phone charger that plugs into the lighter socket. I've observed the voltage fluctuation that you all have described as normal - sometimes indication only 12.8 volts. That really concerned me until I was enlightened about how the system works. The only issue I'm concerned about with the alternator is that I have observed voltage readings as high as 15.2 volts. That is too high, especially since the battery is basically fully charged. With all that being said, I'm still concerned about the flickering lights. I've read a lot about bad grounds, etc, but now I'm thoroughly confused. Any suggestions would be appreciated.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • Still looks like a rivet to me in the pics, I don't see a nut and none of the pics show the head of the screw. But if you says so.....
    • Thanks for all the help so far!   I did try right from 2026 right down to 2021, and only from 2023 down lets me select the option for tire psi change, but I get the vehicle not supported error!   I'll definitely try it under Chevrolet after work today, and I'll get the sensor number from gm for my truck tire sensors. And I'll let you know if it works for me under Chevrolet!   And if that doesn't work, I'm going to guess that what @Atlas said about maybe I have a different body control module could be true!  
    • From where I'm sitting this sounds like a compatibility problem. I'm assuming the 2007 was a 900-series truck, and not an 800-series (they were sold side-by-side in dealerships that model year), since it starts and runs.   This is why I HATE post-2006 vehicles. Everything becomes a huge problem when you try to keep the thing running for longer than the manufacturer has designed it to.    I can't remember when Global-A architecture started - either '10 or '11. For your sake, you had better hope it's '11, or you're going to be spending some BIG money to correct this cluster-eff. That's something you need to find out before doing anything else. You may have several computers bricked ... but the fact that it runs tells me you MIGHT be ok here.     EDIT: Just did a quick refresher. You're screwed. This is Global-A. The 2 systems are NOT compatible in the slightest. Once you get the correct engine in there that IS compatible, you're going to need to see how many computers are locked. Absolute NIGHTMARE to straighten out, too. Your buddy might be better off cutting his losses and finding something else.   Welcome to post-2006 vehicle electronics. This is why I quit the industry, and drive nothing built after 1994. This stuff takes all the fun out of wrenching!  
    • Recently acquired new 2026 Silv. 1500 WT  - L3B + 4WD,  std cab + std bed, in (duh!) Sierra White. Upgrades: replaced 'steelies' w/  Vision "Flow" black alloys,  17x8.5"; HDX nerf bar w/steps (black powdercoat); Weatherguard large/deep alloy saddle toolbox; Michelin fitted bedmat (sale, perfect fit) Weathertech door sill guards TBD: rear wheebox liners 4x black fender arch trim - searching for best  (Putco: chrome only; not looking for flares either!) -Bill    
    • True, hard to say what differences there may or may not be between Chev and GM as well as a production year or mid year part change either.    I just found it odd that under the Sierra choice on the Autel that many of the last few years of production year did not include the choice of changing the tire pressure but if that is an Autel thing or a GM thing as to why the choices were not there. Knowing what tpms sensors are on the truck should give some guidance into which choices on the tool even make sense to try as I wouldn't give up just yet with the tool but I guess he will see what if anything he comes up with if he finds out a bit more info and tries a few more things on the Autel. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...