Jump to content

Service Rear Vision Camera appears on MyLink screen 2014 Silverado Hig

Mac071401

By Mac071401
in Troubleshooting & Recalls

 Share

Recommended Posts

Mac071401 New Member

Mac071401

Posted
Posted

I have seen some threads about "Service Rear Vision Camera" appearing on the MyLink screen, but haven't seen any fixes.

 

I have a 2014 Silverado 1500 High Country, 70,000 miles, "Service Rear Vision Camera" has appeared on my 8" screen. The distance marker lines still appear. Just do not get a picture from the camera and has "Service Rear Vision Camera".

 

I have inspected and cleaned the wiring and plug for the camera under the bed. Inspected the camera attached to the handle from the inside. Nothing appears damaged or worn.

 

What do I need to service to correct this?

How do I reset the rear vision camera with the MyLink Equipment?

Is there a fuse or relay that may be causing the problem with the connection?

Do I need to replace the cable?

Can installing LED brake/turn/park lights cause this issue?

 

Can anyone help?

 

Thanks,

Jerry

 

stevev Enthusiast

stevev

Posted
Posted

I doubt this may help, but you could try pulling the fuse for the radio screen to perform a reset, it is located in the passenger side fuse panel at the end of the dashboard.

  • Like 1
Dmf10e Enthusiast

Dmf10e

Posted
Posted

I have seen some threads about "Service Rear Vision Camera" appearing on the MyLink screen, but haven't seen any fixes.

 

I have a 2014 Silverado 1500 High Country, 70,000 miles, "Service Rear Vision Camera" has appeared on my 8" screen. The distance marker lines still appear. Just do not get a picture from the camera and has "Service Rear Vision Camera".

 

I have inspected and cleaned the wiring and plug for the camera under the bed. Inspected the camera attached to the handle from the inside. Nothing appears damaged or worn.

 

What do I need to service to correct this?

How do I reset the rear vision camera with the MyLink Equipment?

Is there a fuse or relay that may be causing the problem with the connection?

Do I need to replace the cable?

Can installing LED brake/turn/park lights cause this issue?

 

Can anyone help?

 

Thanks,

Jerry

 

I get the same error message on my DIC, but the "rear park assist" error. Its happened a few times now, but always fixes itself after a few engine restarts. Not sure what the issue is.

Mac071401 New Member

Mac071401

Posted
  • Author
Posted

Thanks for the tip on the radio fuse. Haven't thought of that, so haven't tried.

 

The posts I've seen have been the same....not sure what is causing it and it fixes itself have a few starts.

 

Unfortunately, mine has not fixed itself.

 

Thanks,

Jerry

GMCustomerService Senior Enthusiast

GMCustomerService

Posted
Posted
Hello Mac071401,


I’m sorry to hear you’re experiencing this "Service Rear Vision Camera" concern. Have you brought up this camera issue with your servicing dealer. If not, I’d be happy to reach out on your behalf. If this is something that interests you, please send me a private message including your VIN, full contact information and dealer. Thank you.


Regards,


Anthony J.

GM Customer Care

Bayou-AllTerrain Enthusiast

Bayou-AllTerrain

Posted
Posted

My '17 has done the same thing several times but when it does the lines don't appear. Need to bring it in to be addressed along with several other things I have issues with. This '17 doesn't have near the build quality that my '14 had, but man I love the 6.2. Still very frustrating. [emoji51]

 

 

Sent from my iPhone using Tapatalk

  • 1 month later...
  • 10 months later...
LFZ Enthusiast

LFZ

Posted
Posted

Had this happen to me over the weekend....it seems to have fixed itself, but anyone have any ideas on whats going on here?

likeschevy Enthusiast

likeschevy

Posted
Posted

I have had it happen still get the picture from the camera just has the same message on the screen happens randomly

  • 2 years later...
jwhitesides Enthusiast

jwhitesides

Posted
Posted

2014 Silverado with same issue. Seems like when I jiggle the gear lever sometimes it starts working like its a switch that's not activating fully. I would be interested if anyone knows a good fix.

  • 3 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Another JR
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By Another JR · Posted

      Have considered installing a DC to DC charger in your camper to replace your isolator?  
    • newdude
      Gas fill door

      By newdude · Posted

      Common failure.  You need to replace the fuel door housing.   The painted cover transfers over to the new housing.  To remove the old one there is 4 spots where you poke the plastic to release it.  
    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      I have an observation and a question... 1) I watch the voltage closely because I have had to dial in the cut-in/cut-out voltages of the battery separator to my camper.  The "smart" charging drives me nuts.  Anyway, I noticed that when coasting for a while, and especially if lightly using the brakes (though not necessary), the voltage goes up from mid/high-13 volts to mid/high-14 volts.  Then it drops back down after stopping or going again.  Consistently!   The only explanation I can come up with is REGENERATIVE BRAKING!  Well, maybe that's a little bit of an exaggeration, but it's certainly free extra battery charging.   2) Driving on mountain roads I will use L and vary the max gear.  Things straighten out and I end up in L10.  Sometimes I leave it there for a while.  Is there any difference between L10 and D?   

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...