Jump to content

Recommended Posts

Posted

Stealthbox was a HUGE upgrade from stock. Shakes the seats, console, rear view, etc. I’m sure the $1200 dual 10” rear stealthbox would hit harder. 

 

I am am not happy with the small air leak my $600 retail stealthbox had from the factory. Been kicked around with support. Yes I could just seal it myself but a $600 premium JL product should not have an air leak which sounds like a rattle. 

 

If anyone orders this test before installing. 

Posted (edited)

FYI Stealthbox is fiberglass

Factory bose is plastic

running JL with recommended xd300/1v2 amp

Stock bose 6” sub vs 10” JL Stealthbox for under center console 

B212DE48-D9E4-4B7B-9492-7CCB6BFA8999.jpeg

Edited by 2009GMC
Posted

The Stealth box looks awesome but way too expensive and probably overkill for what I want.

Sent from my Pixel 2 XL using Tapatalk

Posted (edited)
11 minutes ago, truckmann said:

The Stealth box looks awesome but way too expensive and probably overkill for what I want.

Sent from my Pixel 2 XL using Tapatalk
 

I purchased through rakuten for 550 - 15% sitewide coupon. Which greatly helped the wallet pain. I checked to make sure the actual seller was authorized for warranty. Even though their support (so far) leaves a lot to be desired 

Edited by 2009GMC
  • Like 1
Posted

Can anyone give me the rundown on center console removal to replace the factory bose sub? Bout to install an L7 8 and would like to avoid breaking any clips which I am prone to do due in frustration on occasion. 

 

Posted
6 minutes ago, tmkilburn said:

Can anyone give me the rundown on center console removal to replace the factory bose sub? Bout to install an L7 8 and would like to avoid breaking any clips which I am prone to do due in frustration on occasion. 

 

This video is on a jump seat to console swap, but it looks to be the most helpful one I've seen. 

 

 

  • Like 1
Posted (edited)

Alright got my console removed. Wasn't that bad. Anyone else wanting to pull the console to add a sub this is what you need to do. 

1. Lift the console lid and pry up the the console trim that holds the cup holders and outlets. I used a screwdriver and pried it at the locations below as seen on youtube videos.
2014-GMC-Sierra-Denali-1500-Crew-Cab-center-console-02.jpg.8d312dbbee0a00e17e93811d0a437941.jpg

 

2. With the trim removed there will be 2 10mm bolts exposed. Remove them.

3. Disconnect all the connectors on the trim piece as well as the larger harness and the brown USB harness behind the trim piece. 

4. Remove the map pocket trim on either side of the console. They just pull straight out. You may have to move the seats around to get them completely out. With the map holders removed 1 bolt on either side will be exposed. 15mm I think.

5. Move your seats all the way forward and at the back on either side of the console near the carpet are 2 plastic cover. Pry them open from the back with a thin screwdriver. Behind the covers are 2 more 15mm bolts. Remove them.

 

At this point you should be able to slide the console back. I had to lift mine up a bit but it should be completely free

 

Edited by tmkilburn
Correction
  • Like 1
  • Thanks 2
  • 4 weeks later...
Posted
16 hours ago, TripleBGM said:

I may need to do this.  I'm not impressed with the bose system.

Me either... I'm wondering if my bose sub is even working. With the volume up, you can feel the doors vibrating, but feel absolutely nothing when you touch the console. I would think if the sub was working your would atleast feel a little bit.

  • Like 1
Posted
Me either... I'm wondering if my bose sub is even working. With the volume up, you can feel the doors vibrating, but feel absolutely nothing when you touch the console. I would think if the sub was working your would atleast feel a little bit.


Same exact situation here on my ‘18 HC. Trying to decide between an 8” or a 10”. Something tells me that a 10” that close to my ears is going to be too much bass


Sent from my iPhone using Tapatalk
Posted

I added a bass level control knob so I can adjust per music ? 

Posted

Ended up buying the center console box off ebay with the kicker comp 8". I haven't sold my 10" single box that goes under the rear seat yet, but ebay had a 15% off coupon so I decided to buy it. Here's a few pics of the install. I haven't wired it to my amp yet cause I have to remove my backseat to get to it. It was a little hot outside today with a heat index of 108 so I'll finish tomorrow. It took me about an hour and a half to install cause I was taking a few water breaks.
Here's a few pics of the console removed, the stock Bose sub, the new box with 8" sub next to the stock Bose, the 10" sub I removed compared to the others, and the new 8" installed before I put the console back in.42f7e3b4ad8232a97da7487c130bbc63.jpg4e492859dc2316718c9b7a9f9ccd8898.jpg5364e65ad4729206f569de094d742408.jpg3e2cbcd96c831a1522b3241cd33f116e.jpg

Sent from my SM-G950U using Tapatalk

  • Like 3
Posted
Ended up buying the center console box off ebay with the kicker comp 8". I haven't sold my 10" single box that goes under the rear seat yet, but ebay had a 15% off coupon so I decided to buy it. Here's a few pics of the install. I haven't wired it to my amp yet cause I have to remove my backseat to get to it. It was a little hot outside today with a heat index of 108 so I'll finish tomorrow. It took me about an hour and a half to install cause I was taking a few water breaks.
Here's a few pics of the console removed, the stock Bose sub, the new box with 8" sub next to the stock Bose, the 10" sub I removed compared to the others, and the new 8" installed before I put the console back in.42f7e3b4ad8232a97da7487c130bbc63.jpg4e492859dc2316718c9b7a9f9ccd8898.jpg5364e65ad4729206f569de094d742408.jpg3e2cbcd96c831a1522b3241cd33f116e.jpg

Sent from my SM-G950U using Tapatalk



Nice. That is helpful to see. Thanks. Does the wiring look like it will be largely a direct replacement (once you get your amp in there)?

On the back wall are you going to run new power or share with the existing amp?


Sent from my iPhone using Tapatalk
Posted

Nice. That is helpful to see. Thanks. Does the wiring look like it will be largely a direct replacement (once you get your amp in there)?

On the back wall are you going to run new power or share with the existing amp?


Sent from my iPhone using Tapatalk
I'm just reusing my existing amp. I'm removing my 10" under the rear seat so I can put my rear storage back in. All I have to do is connect the speaker wire from the sub to the amp, but I have to remove the rear seats to get to it. While they're out I'll also be able to adjust the amp for the new sub.

Sent from my SM-G950U using Tapatalk

Posted

Nice. I ordered one with the L7 in it using the same discount. No idea when I'll get it installed. I still need to mount my amp and run wiring. 

IMG_20180820_193955.jpg

  • Like 1
  • Thanks 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Injector is being sent off today for rebuild and I estimate I'll have it back in 10 days or so.   It may not be the injector...of course...now that I've torn down the intake again. But, let's rule out the injector and replace those spider legs that have been almost rubbed through.   The truck has always had negative timing and I'm reading "normal" timing at warm idle should be +16 or so. I'm negative 16 to 25 or more, and it's always been like that since I bought it.   A light turned on upstairs last night in the old noggin. Rare, I know...   This will be wild, if it turns out to be the cause!   In 2001, according to the old service documentation, the muffler was replaced. Why? I have no idea, it wouldn't have been rusted through by then. But they did a crappy job.   In 2019, another shop replaced it and noted the prior install was poorly done on the work order. "Exhaust system vibrates on crossmember". Except...I guess they just left it be? I believe the husband, the couple who were original owners, had passed by then. Maybe she said it's just not worth it to have the exhaust system fixed and declined repairs. Very few miles were driven between 2019 and 2025.   The exhaust system vibrates heavily on the crossmember and you can feel it and REALLY hear it, even today. Not always, but at idle, it gets going pretty good sometimes.   What if....   ....What if that's enough to trigger one or both of the knock sensors? Could it be tricking the sensors into sensing knock, so it's pulling timing aggressively? Pulling timing heavily means it's firing after the piston reaches full height which means incomplete burn which means the O2 sensor is sensing a rich condition, which means I've been chasing my tail, and what I thought was an inconsequential problem (janky exhaust) has been THE issue for this truck for 25 solid years?   That would be wild. Maybe it IS wild.   The service documentation thereafter, for years, shows visits for rough idle, replacing O2's, replacing the cat, replacing plugs and wires, a misfire condition, like they could never solve the issue. The injector has been replaced 4 times in 80k miles, that's just crazy.   The secondary theory....   The engine has clearly had a leak at the front seal for a very long time (the greasy trench...). I think the truck changed hands quickly ~2025 because there's Napa receipts from someone I don't recognize in the ownership history. They apparently replaced the timing cover seal, and they did a terrible job. There's RTV smeared all over and the leak I had reduced to a weep by snugging the front oil pan bolts is now a leak again.   HOWEVER....I read about replacing the crankshaft position sensor. Any time the ckp sensor is disturbed or timing cover is removed, the truck requires relearning, and that can only be done through a bi-directional scan tool. Skippy with the RTV probably didn't do the relearn procedure is my guess. His scan tool is lost in a pile of RTV goo somewhere.   So, it's very possible the sensor has been disturbed and the truck is just running on the old learn data but not setting a code for anything. The distributor has since been replaced and so has the camshaft position sensor, so all bets are off for that thing.   In the theme of one step forward, two steps back, I returned the accumulator for the AC. The gal I've been working with at O'Really's has been great. She refunded it under manufacturer's defect and we compared it to the replacement I ordered, and sure enough, the replacement is machined very differently (and a gauge actually fits on it!).   Got it home, installed it, started vacuuming it down.... and I couldn't get good vacuum.   The high side service port, where I replaced the old GM ball valve suspecting that was a source of the previous leak....well, I've clearly exposed whatever pre-existing crack in the line where the service port is welded, and made it much worse. Blessing in disguise? Except there goes another $25, now I'm waiting for a replacement AC line.   In 10-ish days ALL the parts will be here. Rebuilt injector, new exhaust system, new cat, new high pressure AC line.   Oh, did I mention the squeaking ISN'T coming from the AC pump? The truck still squeaks when started, and there were words after I started it with the new AC pump installed. But, there was more to replacing the AC pump for just a squeak. A truck with good working AC is something of value, for the comfort alone.   I've ordered a new harmonic balancer because, 30 years is a good run for one of those. Rule it out. The squeak may be something more sinister, though. I'm worried about that ckp sensor and if it was shimmed correctly, or if the timing set was installed correctly. The squeak may be coming from UNDER the timing cover.   At this point, once I get it put back together, I'm thinking I'll take a 50 mile victory lap and then promptly put it up for sale. This truck is cursed. Betty, from beyond the grave, doesn't want anyone messing with her Blazer. Or maybe she's getting revenge for 30 years of shop visits with that thing.
    • 3.59 Kroger’s in Montgomery Tx. 20 cents higher than most around here. Very unusual. Saturday they were 3.49. 
    • Starting at 17 running parts for my father’s construction business to haul our equipment. Eventually doing shows, sales and training after purchase. I drove a minimum of 50K miles a year. Half hauling something. After retiring 30K miles a year to the last 2 years 15K miles a year. 2/3rds highway driving. The major contribution to fatigue for me is from anticipation and awareness. I just don’t relax. Too many idiots on the road. There’s two kinds. The group that never leave the left lane tied together afraid to let anyone in doing 80. They’re mostly on weekends. Then the left lane sleepers usually next to a tractor trailer not advancing. Eventually the tractor trailer will drift over the sleeper will wake up. The train moves and the tailgaters who are usually mad as hell. You definitely don’t want to mix with them. The tail wagging bumper puller’s with under powered trucks are holding the tractor trailer up. That bunch are dangerous. I usually pace ahead all that. Unless there’s a gap when I can chill and let the speeders pass. I tried all different types of driving. I stay to the right except to pass, it’s the law that’s getting in forced more now because of road rage. I was so happy when my wife didn’t want to do the camping life. I had enough of pulling for work. The family has a bus and fifth wheel. I haven’t driven either one since retiring. No thanks. 
    • Yesterday a suggested youtube video thumbnail caught my attention so I watched through it and it was a bunch of short clips someone gathered together of people pulling trailers, a lot of them were bumper pull holiday trailers and a pickup or suv pulling it. a few fifth wheels as well, some motorhome crashes also. The tail wagging the dog theme was quite evident in numerous self inflicted accidents that took out vehicles around them sometimes in the process as the unit finally swung around and flipped over in the middle of the highway. Or the other classic which literally could be called "I forgot the trailer was back there" in passing another vehicle on a multi lane one way freeway and then cutting back in line before the back of the rv trailer had passed the front of the passed vehicle and often in front of a tractor trailer and that never ended well. Or the wide kick out swing of the rear of a long travel trailer as they have so much overhang behind the axles and the trailer smashes into the side of vehicles in the next lane over ( typically sharp turns in city driving ). It makes one leery for good reason to be near an RV trailer after watching a video like that and be it on the highway, in town, or at a gas station where that rear end comes swinging around due to the fuel station being so cramped and not intended for larger trailers. I wonder how many officers have heard those words though "I forgot it was back there" as they investigate the accident LOL. 
    • $5.10 for regular at the Kroger   It's been 6 months... is this the "new normal" ?
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...