Jump to content

Remote not working 2017 Silverado LT

Jmiller11331
 Share

Recommended Posts

Jmiller11331 Enthusiast

Jmiller11331

Posted
Posted

So I bought a brand new 2017 Silverado about 6 months ago and the major selling point for me was the distance between me and the truck when unlocking and locking the truck. I had a 2011 before and you had to be right next to it to unlock the damn thing so I thought it was awesome to now be able to unlock this thing from a far distance away. Recently it hasn't been working from far away and now it's like I have to get right on top of it to unlock it or lock it.....anybody have any opinions on this? I just wanna hear what you all have to say before I go to the dealership

 

 

Sent from my iPhone using Tapatalk

pmhinatl Enthusiast

pmhinatl

Posted
Posted

Please forgive me for asking the obvious (but you know it’s coming)...

 

Have you tried replacing the remote battery?

 

I wish I knew more about the electronics in these things, but they’ve reached a level of sophistication approaching magic.

 

M.

  • Like 2
Jmiller11331 Enthusiast

Jmiller11331

Posted
  • Author
Posted
Please forgive me for asking the obvious (but you know it’s coming)...

Have you tried replacing the remote battery?

lol I actually started using my 2nd key fob and I get the same results


Sent from my iPhone using Tapatalk
B R A D Enthusiast

B R A D

Posted
Posted

lol I actually started using my 2nd key fob and I get the same results


Sent from my iPhone using Tapatalk
The cell phone app works extremely well although it's not the method you are wanting.

Sent from my SM-N950U using Tapatalk

  • Like 1
Jmiller11331 Enthusiast

Jmiller11331

Posted
  • Author
Posted
The cell phone app works extremely well although it's not the method you are wanting.

Sent from my SM-N950U using Tapatalk


Yes it does!!


Sent from my iPhone using Tapatalk
  • Like 1
ALSLT Enthusiast

ALSLT

Posted
Posted

I wonder if taking the battery out and putting it back into the remote like restarting at computer would work? 

Jmiller11331 Enthusiast

Jmiller11331

Posted
  • Author
Posted
I wonder if taking the battery out and putting it back into the remote like restarting at computer would work? 

But it does this for both key fobs

1 and 2

I guess I could try it anyway tho

 

 

Sent from my iPhone using Tapatalk

 

True North Truckin Enthusiast

True North Truckin

Posted
Posted

Havent personally ever had this issue with my 17' but perhaps you could try the old top gear method:

 

1) Stand just beyond whatever point the remote entry stops working 

2) Hold the end of the remote tight against the temple of your head and press the lock or unlock button

 

This will allow your body to become essentially a large radio antenna booster so If the remote entry then works its an easy way to know its a weak signal issue either from a low battery in the remote or an issue with the receiver within the truck.

 

  • Like 1
Jmiller11331 Enthusiast

Jmiller11331

Posted
  • Author
Posted
Havent personally ever had this issue with my 17' but perhaps you could try the old top gear method:
 
1) Stand just beyond whatever point the remote entry stops working 
2) Hold the end of the remote tight against the temple of your head and press the lock or unlock button
 
This will allow your body to become essentially a large radio antenna booster so If the remote entry then works its an easy way to know its a weak signal issue either from a low battery in the remote or an issue with the receiver within the truck.
 

Lmao haha


Sent from my iPhone using Tapatalk
2017SierraSLT Senior Enthusiast

2017SierraSLT

Posted
Posted

You're also assuming that both batteries are good. Try putting a new battery in a remote and see if the problem is gone.

  • Like 1
Jmiller11331 Enthusiast

Jmiller11331

Posted
  • Author
Posted
You're also assuming that both batteries are good. Try putting a new battery in a remote and see if the problem is gone.

True, I'll get some battery's and test it out


Sent from my iPhone using Tapatalk
  • Like 1
Jmiller11331 Enthusiast

Jmiller11331

Posted
  • Author
Posted

IT WORKED!! The new battery fixed the damn issue......it's crazy tho because the truck is only 7 months old I believe now


Sent from my iPhone using Tapatalk

  • Thanks 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • davester
      Bench seat swap for 2021-2024 suburban

      By davester · Posted

      probably won't get a response from that user, as they haven't returned to the site since making that one post.  users don't (at least I don't, and I haven't seen any setting which would notify me via say, email) get any notification other than going to this site, and checking if they got a response on their thread...
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Thanks - I wasn't quite caffeinated this morning. 2:1 makes sense, turning the crankshaft 360 degrees will turn the cam 180 degrees, and had I done that, the cam's dot would be at 6 and the crank's at 12 again.   I went ahead and took the sprocket off anyway, aligned everything dot-to-dot including the balance shaft just for s&g. I'm glad I did because I discovered no Loctite on the timing sprocket bolts. Maybe it's not required, but at only 20 ft-lb torque spec, those bolts aren't in there very tight. Cleaned and reassembled with some thread locker and torqued.   A general observation: Less is more with RTV. If a little doesn't stop a leak, a LOT probably won't, either. RTV is thinly veiled revenge, in a tube...      
    • richard wysong
      Wow I'm in a pickle. (Broke down truck) and a story.

      By richard wysong · Posted

      The timing marks are ok, that is #1, you can turn it over until they line up and it won't change anything, the crankshaft turns twice for every camshaft revolution, I have always set up SB Chevs as your pic shows using a straight edge
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Someone's been here before.... There is a receipt for a 3-piece timing set, purchased earlier this year.   Is this picture something, or, nothing?   I have the timing cover off and my crank is perfectly TDC and the keyed gear's locating mark is dead on 12 o'clock.   The cam gear locating mark is also at 12 o'clock. Now, I'm not an expert, but all the install guides say the two locating marks should meet and be perfectly aligned when installing a timing set. The mark on the crank should be dead on 12:00 and the cam gear's mark should be dead on 6:00, and both marks should be perfectly vertically aligned.   I believe the timing gear is keyed or has a dowel that ensures it can only be installed on the cam in one position, so I have to believe the cam is out of phase somehow. At the very least, with a triangular bolt pattern, it can only be installed in one of 3 different positions.   Before I pulled the front cover, the truck was running alright, no service engine soon lights except an occasional P0172 / rich condition. Timing -16 timing at idle (should be +16), and total -35% fuel trim, two conditions I haven't been able to figure out.   In related news, my injector tested pretty well, wasn't leaking, but I had it rebuilt anyway, and it's on it's way back to me.         Along with this discovery, the good and bad:   Good: The oil pan seal appears undamaged.   Bad: -The timing cover has been reused, and the positioning dowels have been broken. That could explain some of the leaking. -Some kind of white paste or grease was used to try to seal the oil pan seal and timing cover (since wiped off..). -Then, someone globbed silicone all over the front of the cover and also buried the ckp sensor in it. But, they didn't put any inside the cover or use RTV to try to seal the oil pan seal with the timing cover (good).
    • Grumpy Bear
      PF63 Oil Filters Going Away?

      By Grumpy Bear · Posted

      The guy that owns K&P filters last I checked in with him has over 300,000 miles on his Dodge base Hemi using his own 35 micron absolute stainless mesh filter from its first oil change.    The GM study I've posted a dozen times shows the relationship in engine life based in multiples of base units, not miles or years. That is the base unit is the number of miles the motor ran using the reference filter efficiency.    The above two paragraphs dismantle anecdotal arguments IF one changes oil often enough to prevent particle formation and the motor is in otherwise good shape. That is not full of silica (no air filter) or suffering a metallurgical issue that is not part of the lubrication discussion. Poor heat treat in example.   Data from UOA's I've reviewed from more than a few engines can show remarkably broad variations in oil cleanliness using the exact same filter over the course of an engines life.     Lastly there is the common sense of it. Wear debris WILL circulate the engine BEFORE it ever sees a filter in route to that filter and WILL harm the pump which NEVER sees filtered oil.    Alpha question then becomes, given the facts, how long do you believe is a reasonable service life from a vehicle you are certain you will not pass down? That is the junk yard will be it's resting place when you're done with it? (the moral issue most don't care about).    Omega question is then how diligent are you prepared to be in general mechanical, air & oil maintenance? Preventing particulates and keeping them sufficiently dilute; preventing the precursors from generation, amalgamation and precipitation.    If I get a good look at the engine bay of a vehicle I have a fair idea of the owners commitment to the inside of the power train. That 30 micron WIX is still more efficient than a sieve.                 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...