Jump to content

"Check Trailer Wiring" Solution?

blackedout96
 Share

Recommended Posts

blackedout96 Enthusiast

blackedout96

Posted
Posted

I've had this issue now with two new trucks. The first a 2014 Silverado 1500 and now my 2016 Sierra Denali. Any trailer I ever connected them to I constantly get the "trailer connected" message followed by "check trailer wiring".

 

I'd love to blame the problem on trailer wiring, but the same trailers function perfectly when connected to Ford trucks and older GM's. This isn't an intermittent, works on some trailers not on others thing. Neither truck has ever cosistently operated the brakes on any trailer properly.

 

I've never seen a recall or GM acknowledgement of the issue, just wondering if anyone has ever found any solution.

bdbake01 Senior Enthusiast

bdbake01

Posted
Posted

Curious myself. I have the same issue.  When it happens, the brakes stop functioning until I turn the truck off and back on.  Not cool. 

badge171 Enthusiast

badge171

Posted
Posted

Bad ground somewhere in the trailer. Some trailer's the ball will make the ground circuit. Not so, needs a dedicated ground on the trailer, The lighter the ground wiring diameter gauge. The weaker ground is produced.  

MySilverado180 Enthusiast

MySilverado180

Posted
Posted

I have had this issue on multiple occasions towing an RV. The 7 way connector is a very loose fitting, and when it loses connection, I get this error message on the DIC. Always have to re-seat connector and turn vehicle completely off to get it to reset.

 

Tried electrical tape to make it a tighter fitting. Worked better, but not great. Found that I had to tap  the 7 way in further by a little less than 1/2 inch. It then grabbed properly and no more issues. Very tight fit when I did that, was almost afraid of breaking something. 

 

Thanks for the TSB link above. I will also try getting the Pollak connector.

avgas Enthusiast

avgas

Posted
Posted

For some reason people who wire trailer plugs do not think they need to connect the ground wire. The ball just doesn't provide a good enough ground. Check the trailer ground, Its likely the issue. 

blackedout96 Enthusiast

blackedout96

Posted
  • Author
Posted

Ordered a Pollak plug for my trailer, we'll see if that helps.

The frustrating part for me is that I pull customers' trailers frequently and I can't go changing their plugs for the one time I tow them. I also have a 2014 F-150 for my shop truck and that operates all of them properly every time. I just have to use my personal truck when that's busy, which is most of the time.

The problem is so widespread and well known that GM must simply have no interest in fixing it. If Ford's 7-ways are forgiving enough to work on all trailers without special provisions, then GM should seriously consider trying a new style plug.

  • 1 year later...
donaldbailey New Member

donaldbailey

Posted
Posted

my 2018 gmc is doing the ….. check trailer wiring  …...trailer connected ...on dash display 

trailer brakes don't work when check trailer wiring comes on 

 

GMC put on new truck reciprocal  didn't help 

I changed trailer plug... twice 

I ran separate ground from  trailer to truck 

still does it

 

trailer works fine on other peoples gmc truck 

 

any ideas would be appericated 

 

 

MySilverado180 Enthusiast

MySilverado180

Posted
Posted

I also had similar issues and even had the dealer look at it. Everything was working correctly according to GM. Also noticed the loose fitting plug. Seemed too loose to maintain electrical connections. So I looked inside the receptacle and if you look closely you can see what looks like a quarter round piece of trim between the base and the wall. I figured my plug was going just above this, keeping it loose.  Next time I towed, I had to push really hard to get the plug to seat inside that quarter round.  It did! The plug was now tight, and never had the problem again. If you do this, just make sure the plug is aligned with the pins correctly and should be 95% of the way in, still loose fitting. That last 1/8 of inch is the push really hard part.

 

good luck.  

kenny_r Enthusiast

kenny_r

Posted
Posted

My truck does the same thing...2017 hd. There is just enough play on the trailer side connection that it triggers the message. Sometimes you can bend the tabs on the female/trailer side and it will work. That was the case with mine at least.

donaldbailey New Member

donaldbailey

Posted
Posted

Thank you i will look at that 

i hooked a tarp strap to plug yesterday seemed to help but still does it 

 

going to measure today to see if it is going into socket all the way 

 

i will look at bending tabs 

also ordered a different plug for trailer ...one thar somebody suggested

i do appreciate all the ideas 

  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • SwitchBladeSierra
      HELP! DUMPING COOLANT

      By SwitchBladeSierra · Posted

      If anyone lands here looking for an update - the problem wasnt with the hose, the clamp, etc... I purchased a metal Thermostat housing that just must not of been made to spec. It just wouldn't plug up the hose.. Went back to a plastic cheap housing - leak fixed. Some plumbers tape carefully placed in tandem with a clamp likely would've gotten the job done.   Best,
    • SwitchBladeSierra
      AUX switch install

      By SwitchBladeSierra · Posted

      For anyone following, this is what I have deduced from this forum - and my very specific niche case. Please do let me know if you see me going in the wrong direction here. For context, I have a 16 sierra 1500 w/t. Has TC and Cargo light switches. Removed the switch to find the X1 and X2 of the S48A connection populated with wires (x1 10-14, and x2 1-5).   Took photos of the X61A-X5 to find the wires from S48A-X1 land here at their respective pins (10, 11, 17, 23 on the X5). Was hopeful that this means my X51A fuse box has the appropriate pins... No cigar. So now I will be routing wires from the rear of the X61A-X1 to the engine bay and to their respective negative relay triggers. Please see to the diagram. If any has insight as to where the S48A-X2 pins 4 and 5 land that would be awesome.   Note: please disregard fuse sizes. Main fuse will like be 25A, all mini bus fuses will likely be 10-15A   Cheers
    • Grumpy Bear
      Sugar Bears 2015 GMC Terrain SLE-2 2.4 AWD

      By Grumpy Bear · Posted

      287,500 Mile Service   8/13/2026   Reset Fuel Trims   Since the work done in the previous post there was a good improvement in response in all areas except right after a fill up where the LTFT would go -20%+ for about four miles while the STFT was near neutral. Before the work they both went very negative for a few miles after a fill up but act normal thereafter.    We did a systems check of the vapor recovery system for functionality and ability to hold a vacuum. That checked out fine. But this doesn't mean the charcoal canister is dead in the water. Testing that is next up. For now the reset of the fuel trims.    I intentionally shorted the fill exactly two gallons to eliminate any chance of filling the canister. On start up the trims were behaving normally until I got up and rolling where the LTFT went -10 / -11%% but the short was + 2 to 0%. Within a mile the the STFT offset the LTFT and by 2 miles they were neutral. HUGE improvement but still not hunky-dory.    I'll watch them for a few days. Perhaps another tank where I will fill completely to 'first click' and compare. Meanwhile on the hunt for a new canister and I'll toss another purge value at it for good measure. Pending the outcome of the canister test that is. Progress of any kind is welcome.    Fuel economy improvement with bringing hole #3 back to the living was a noticeable bump to the positive. Even on the few miles I drove after the refill I already see another bump up by the trims reset.     She's purring like a kitten with a warm bowl of milk.    BTW, adding 50 rpm to the idle took the majority of the negative timing out on cold start up and leaned the cold idle. No longer burbles in the cat. What a dumb way to heat a cat.      
    • OnTheReel
      Post your UOA, (used oil analysis) here

      By OnTheReel · Posted

      Yeah, shame I can’t really get that filter easily anymore. Running a PureOne. Your fave!    TAN would be neat to see. Confirmation I ran it too long probably. 🤣
    • superdave160
      Roll up bed cover experiences

      By superdave160 · Posted

      My son and I both bought new trucks in 2017. Both of us immediately put Truck Covers USA American Roll Covers on our trucks. My son still has his truck and it never sees the inside of a garage. We live in Alabama, so not much snow. My truck was my daily driver and was in the garage when I wasn't driving it or at work. No issues with either cover even after almost 9 years. About a year ago I sold my truck to my brother and bought a 2025 Silverado 2500. The second thing that I put on that truck was a new Truck Covers USA cover. They are very well made and have a very positive locking system. I looked at a Retrax and my concern was the way that the cover locked to the rail. BTW, the first thing I put on the new truck was step bars. Those new trucks are high!

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...