Jump to content

Recommended Posts

Posted (edited)

I doubt as there has been some RCSB Trail Boss mules running some sand dunes.

 

I can confirm that the 6ft6in box is body tagged 03-43-53 so 03 = regular cab, 43 = crew cab 53 = double cab.

 

Regular cab is last to launch too, I assume due to the fact that Ft.Wayne is handling crew cab and double cab launch production.  Once Silao starts spitting out crew cab T1 trucks (they are still doing 2018 crew cab), the regular cab will ramp up at Ft.Wayne. 

 

Given how K2 was, I'd expect WT and LT for sure, and we might get Custom, Custom TB, RST and LT TB.    

Edited by newdude
Posted
4 hours ago, newdude said:

I doubt as there has been some RCSB Trail Boss mules running some sand dunes.

 

I can confirm that the 6ft6in box is body tagged 03-43-53 so 03 = regular cab, 43 = crew cab 53 = double cab.

 

Regular cab is last to launch too, I assume due to the fact that Ft.Wayne is handling crew cab and double cab launch production.  Once Silao starts spitting out crew cab T1 trucks (they are still doing 2018 crew cab), the regular cab will ramp up at Ft.Wayne. 

 

Given how K2 was, I'd expect WT and LT for sure, and we might get Custom, Custom TB, RST and LT TB.    

God I hope you are right! Thanks

Posted

Well GM Canada just messaged me back saying that reg cabs will be with 8ft boxes only. They have been wrong before in there messages to me. I hope they are wrong again!

Posted
24 minutes ago, Likarok said:

On page one of your attached guild I see code 107 with a 6'6" option under the reg cab column. Am I reading it right?

Yeppers. 

  • 2 weeks later...
Posted

I can't wait to see the double cabs!  Anyone know when they are hitting the lots?  I've only seen those photos of the blue model from the car shows.

Posted
Sierra Elevation Edition Double Cab:
 
Elevation.thumb.png.fe7d6a9047c192f85e55de39a3fb270b.png


I swear that looks like a freaking Tundra!


Sent from my iPhone using Tapatalk
  • Like 1
Posted

I currently own a GMC, but the 2019 GMC would not be in my Garage! :sick:

Silverado looks so much better in the front, and tail lights.

These GMC tail lights remind me of the 2005-2012 Colorado/Canyon style.

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,915
    Total Members
    8,960
    Most Online
    ChristopherDobson
    Newest Member
    ChristopherDobson
    Joined
  • Who's Online   4 Members, 0 Anonymous, 1,301 Guests (See full list)


  • Latest Articles

  • Posts

    • I have the same running boards on my truck and I do agree they are bulky. I also find myself stepping over them when getting in and out of the truck. Besides providing protection to the rocker panels, they aren't very useful.  I will be replacing them soon with the Amp Powersteps. 
    • Monthly payment is only part of the equation. With today's prices and interest rates, I'd look at the total monthly cost: payment, insurance, registration, fuel, maintenance, and expected repairs. A vehicle that fits comfortably into your budget is usually the better choice than stretching for a higher trim. I've also kept my vehicles longer over the past few years. New cars have gotten expensive enough that driving one for 10+ years, while staying on top of maintenance, often ends up being the most cost-effective approach.
    • 10 Ford and Chevy engines proven to reach 300,000 miles   You may note a common 3K OCI on this list of gas motors. I skipped over the diesels. Dh'O. 
    • Thanks newdude!  By the time manual selection is needed, I'm probably too much of a control-freak to depend on the transmission sensing braking to activate automatic downshifting.  I would be anticipating the situation and already be manually downshifting.   This truck replaced a 2004.5 LLY diesel with the Allison 5-speed.  Putting it in T/H made noticeable differences (when the torque converter locked, upshift points, downshift behavior).  On this 2024 gasser with the 10L1000 I haven't been able to detect much, if any, difference.  Ok, I can never tell now when the torque converter locks up.  But I also don't notice differences in shifting.  For downhills, I've probably already manually downshifted by then anyway.  Since it's also more awkward (than the 2004.5) to engage/disengage I don't even bother.  Or maybe it doesn't really matter with just a 3k lb. camper in the bed?   Thanks also for the list of reasons the charging system might select various voltages.  However, what I am seeing doesn't fall into any of those categories.  It very definitely, and very consistently, rises after coasting/braking.  Maybe not immediately, but not very long after coasting/braking.  Very consistently drops voltage when no longer coasting/braking.  It might also be interacting with the camper battery charging (I might disconnect the camper and see if it changes the charging behavior).  I also need to recheck turning on headlights for when I want to force it to charge the camper.   Another JR, in June I converted the camper to LiFePO4.  Since it's not a good idea to try to charge lithiums directly using truck, I installed a Victron Orion XS DC-DC charger (which BTW is AMAZING!!).  Being cheap, I only had to buy that one item (besides the battery, of course) to do the conversion.  The camper OEM 120v battery charger (only 19 years old and works perfectly) and the truck feed the input to the DC-DC charger (not at the same time).  But I didn't want the camper charger feeding back to the truck so I kept the old separator.  I considered replacing the separator with a 30amp diode but that means more work and might add another 1/2 volt drop.  One thing that surprised me was the voltage drop over the long 10awg wire run, so I can only charge smoothly at 8 amps (because the DC-DC charger is completely configurable).  Another reason I don't want an added voltage drop with the diode.  I might also be a little lazy but all this work is being done under the sink with a small cabinet opening.    
    • apparently CA smog is (or at least was)  checking that the vehicle is using the oem and/or a ca smog approved tune, so I expect you'll fail inspection doing it.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...