Jump to content

AT4 rubbing with 35s and 6” lift

Antonio Kheir
 Share

Recommended Posts

Antonio Kheir Enthusiast

Antonio Kheir

Posted
Posted

Hey guys. Just made an account! So my dad just bought a 2019 Sierra AT4 and installed a 6” RC lift with 35” ridge grapplers on a 22X10 wheel with 1/4” backspaces. He has the gmc brembo upgrade kit. He seems to be rubbing on the outer front fenders while turning with minimal flexing. I don’t have the specs for the offset nor the backspacing  yet. I will be getting that info tomorrow. Any ideas on what he needs to do to minimize or eliminate the rubbing? He put me in charge of figuring this stuff out haha. Thanks!

A7113F0F-6DF5-4DC0-94A1-49B1A94864EC.jpeg

2F5F4E87-1B58-498C-8078-1D612000733A.jpeg

2D261572-8350-4CEF-90B2-9D5D52C11D84.jpeg

jimmyboy8301 Senior Enthusiast

jimmyboy8301

Posted
Posted

first off since that's an AT4 according to RCX their 6" kit will not fit it, only their 4" kit. I'd check to confirm it actually has the 4" kit being as according to RCX the 6" kit will not AT4's. I'm assuming the tires are rubbing due to the width and backspace/offset of the wheels and the GMC's HORRIBLE fender design. Your most viable option is to trim the inside of the fenders a little

gothp28 Enthusiast

gothp28

Posted
Posted

Those rims should not need a spacer so if you removed the space and you would move the tire a little more in the Fender and it should clear no problem.

Sent from my SM-G965U using Tapatalk

z1boss Enthusiast

z1boss

Posted
Posted
54 minutes ago, jimmyboy8301 said:

first off since that's an AT4 according to RCX their 6" kit will not fit it, only their 4" kit. I'd check to confirm it actually has the 4" kit being as according to RCX the 6" kit will not AT4's. I'm assuming the tires are rubbing due to the width and backspace/offset of the wheels and the GMC's HORRIBLE fender design. Your most viable option is to trim the inside of the fenders a little

The 4" inch kit for the AT4/Trailboss turns the lift into 6".  Its on top of the 2 inch lift from the factory

z1boss Enthusiast

z1boss

Posted
Posted
55 minutes ago, jimmyboy8301 said:

first off since that's an AT4 according to RCX their 6" kit will not fit it, only their 4" kit. I'd check to confirm it actually has the 4" kit being as according to RCX the 6" kit will not AT4's. I'm assuming the tires are rubbing due to the width and backspace/offset of the wheels and the GMC's HORRIBLE fender design. Your most viable option is to trim the inside of the fenders a little

The 4" inch kit for the AT4/Trailboss turns the lift into 6".  Its on top of the 2 inch lift from the factory

jimmyboy8301 Senior Enthusiast

jimmyboy8301

Posted
Posted
25 minutes ago, z1boss said:

The 4" inch kit for the AT4/Trailboss turns the lift into 6".  Its on top of the 2 inch lift from the factory

i understand that, but he stated he has a " 6" RCX lift" which would indicate it's running at 8" since 6+2=8 , where as he's running a 4" RCX 4+2=6. If he was at 8" ride height and rubbed it would be a lot more disconcerting than being at 6" and rubbing...........

Antonio Kheir Enthusiast

Antonio Kheir

Posted
  • Author
Posted

Thanks for the responses. So I made a mistake, it’s actually a 4” lift kit but a 6” total as y’all stated. The wheels are a -24 offset and 4.5” backspacing. The front wheels would not clear the calipers of the Brembo brakes so we had to add the 1/4” backspacers. 

jimmyboy8301 Senior Enthusiast

jimmyboy8301

Posted
Posted
10 minutes ago, Antonio Kheir said:

Thanks for the responses. So I made a mistake, it’s actually a 4” lift kit but a 6” total as y’all stated. The wheels are a -24 offset and 4.5” backspacing. The front wheels would not clear the calipers of the Brembo brakes so we had to add the 1/4” backspacers. 

those spacers are most likely the reason it rubs

f8l vnm Senior Enthusiast

f8l vnm

Posted
Posted

I have nothing to say to help but just damn! That is a nice rig mate. Love the stance 

Antonio Kheir Enthusiast

Antonio Kheir

Posted
  • Author
Posted
1 hour ago, jimmyboy8301 said:

those spacers are most likely the reason it rubs

So basically I need to tell the dealer to put different wheels with less offset, that way it tucks in the tire a little more.

jimmyboy8301 Senior Enthusiast

jimmyboy8301

Posted
Posted
So basically I need to tell the dealer to put different wheels with less offset, that way it tucks in the tire a little more.

Or get wheels that don’t rub the calibers (the best option)


Sent from my iPhone using Tapatalk
Antonio Kheir Enthusiast

Antonio Kheir

Posted
  • Author
Posted
1 hour ago, jimmyboy8301 said:


Or get wheels that don’t rub the calibers (the best option)


Sent from my iPhone using Tapatalk

The wheels I’m looking at are fuel D616 with -18 offset. Is that enough offset?

jimmyboy8301 Senior Enthusiast

jimmyboy8301

Posted
Posted
The wheels I’m looking at are fuel D616 with -18 offset. Is that enough offset?

Or the same size wheel that clears the brakes


Sent from my iPhone using Tapatalk
gothp28 Enthusiast

gothp28

Posted
Posted
So basically I need to tell the dealer to put different wheels with less offset, that way it tucks in the tire a little more.
Backspace 4.75 should fit no problem

Sent from my SM-G965U using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • BIGBOYS
      Doors lock and mirrors fold in while driving

      By BIGBOYS · Posted

      I have a 2015 Silverado and sometimes I can not get in to the truck. I use the key to unlock the driver door. Something is locking the truck when I unlock it, last night I left the truck open and this morning it was locked with the mirrors folded in. This happens while driving so it is now a safety issue. I reach down for the folding button and they open, then they close again.  Any advice, thank you,   Ed
    • Paul8556
      Headlight issue...

      By Paul8556 · Posted

      Did you ever find a resolution to this? my 2019 Silverado 1500 is showing the exact same headlights issues with the exact same symptoms.  would help a ton if anyone has any advice on this or better yet a known solution..
    • RyanbabZ71
      Gas Prices

      By RyanbabZ71 · Posted

      Wawa and Meijer here have ethanol free (88 & 89) I use for my mower and lawn equipment.  Its not much more than reg.  I paid $3.29 a few weeks ago.  
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      tl; dr I've now reached the 6th floor of hell. I'm chronicling my journey for my morning readers.   Pulling the top of the intake apart was moderately easy but it involved a lot of parts, connections, and minutae. I was preparing for the new fuel lines to arrive ("nut and bolt kit" it's called). The fuel line connections are notched and held in place by the manifold and a metal plate with a T27 screw.   It's on the back of the intake, under the firewall, with little clearance, and two hard metal fuel lines in the way. I was using Franken-tools (weird combinations of 1/4 inch ratchet with/without an extension, with a bit holder for my T27) to get in there. One of my sockets and bits fell off and has yet to emerge on the floor. I lost a second setup and that's when I almost started throwing tools. But that was the point at which I had gotten traction on the Torx head, and it promptly stripped. No more traction.   I started humming "1-877-kars-4-kids" because I was about at that point. You know what? I'm $1500 into this thing and I can make it disappear just as quickly. This isn't fun anymore. I had spent a lot of time already "tidying" around the engine bay: Fixing all the "someone's been here before!" BS. The truck has been exclusively dealer- and shop- serviced and I'm reminded of why I never let other people work on my cars unless absolutely necessary.   Speaking of dealer service. This truck has a 1" stack of records going back to 1995. I put them all in an excel spreadsheet, date/mileage/description.   The CPI spider has been replaced 4 times in 85k miles. The EGR? Another 4. Multiple, multiple O2 sensors. One Cat. 4? Sets of plugs and wires, and I swear half the stack is diagnosis paperwork for "misfire, runs rough, extended crank, dies at stoplights".   GM was producing some proper crap back then. And it was still well within the era of brittle/crappy plastic. (Windows 95 was released the same month this truck was sold new, we HAD the technology!!)   There (was) a plastic shroud around the evaporator core and HVAC fan in the engine bay. I noticed a chunk of it missing so I poked at it some more and it literally shattered. Touched it some more and pieces were crumbling off. Had a good laugh. Clearly whatever plastic garbage they were using had broken down over 30 years and was literally turning to dust. That was a good half hour of using a shop vac to remove the rest of it.   Back to it.   I was going to give up for the evening but then decided I'm already level 10 pissed off at the stripped screw: G* D* it, give me my tools back -- and my JOY. We'll do this the hard way: The whole intake is coming off.   Blazer won Round II. After finally finding and accessing the 12 intake bolts and using a pry bar to unseat it from the heads, it popped loose in an explosion of gunk and grime raining down into open ports. Awesome.   6 times I reminded myself: Be careful of the temperature sender on the front of the intake.   YEAH, I forgot again and snapped it clean off in the removal. Add another $20 to the ever-growing list of new parts this thing is consuming.   The shame is, long before removing the intake, I had changed the oil in prep for Tuesday's momentous fuel line replacement that was going to be the magic fix and I'd have a running Blazer to tool around in this next weekend. The intake removal, including raining gunk, also gushed dirty coolant all over the valley. Of course it did. Welp, there goes another $35.   I now need an intake gasket set, bolt set, coolant temp sensor, another 5 quarts of oil, some RTV. Don't worry, I've already got 3 new jugs of Dexcool and a thermostat waiting. I'll fill it with clean water first to get it running, dump it, and then add the Dex later on in case... well, let's not go there. I'm only tearing this down once, next time the truck is going on Marketplace for FREE.   Oh, and I'm going to need vacuum hose for all the stupid connections placed at the rear of the engine which have since disintegrated. Come on, GM....tell me you don't do that anymore?   Oh, and the ears on the distributor where the cap screws down are both cracked. I mean, why not put a new distributor in it too. You get a distributor, YOU get a distributor, Everyone gets a new distributor!   This truck isn't out of the woods yet...I'm already questioning how much more time I'm willing to sink in.
    • William Aldrich
      Bent valve in 2025 GMC Canyon Denali - Requires engine swap at 14K miles

      By William Aldrich · Posted

      NewDude, thank you for the suggestions!    I did follow up and the dealer indicates he has an open CX case and is working with DPAC (Dealer Parts Assistance Center).   Per the dealer, GM has had a quality spill and is not providing an update for when a replacement engine will be available.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...