Jump to content

Huge difference, large mpg loss 65 mph to 70 mph. Any idea what may be causing it, my gears?


Recommended Posts

Posted

I commute 5 days a week on my 5.3L/6 speed, been doing it for years. Did it on a 2014 double cab and a crew cab. Crew cab was a few hundred pounds heavier.

Really didn't notice much difference in fuel mileage between the two to care about.

Bear in mind, I'm in Florida and the road is flat as can be. We get windy days, but I've never paid attention to that. But wind can be pretty restrictive.

Sent from my SAMSUNG-SM-J727A using Tapatalk

  • Like 1
Posted
10 hours ago, HeySkippyDog said:

I commute 5 days a week on my 5.3L/6 speed, been doing it for years. Did it on a 2014 double cab and a crew cab. Crew cab was a few hundred pounds heavier.

Really didn't notice much difference in fuel mileage between the two to care about.

Bear in mind, I'm in Florida and the road is flat as can be. We get windy days, but I've never paid attention to that. But wind can be pretty restrictive.

Sent from my SAMSUNG-SM-J727A using Tapatalk
 

What do you mean flat?  What about all them hills (highway overpasses) every mile or so?  ?

 

There does seem to be a slight grade to I-95, we get less mpg going north and better heading south, generally speaking.  The grade is contrary to prevailing winds, on the east coast anyway.

Posted (edited)

I was getting readings of 10.5L/100km (22.4usmpg) on stock tires. When I put on my 33x12.5 10 plys I get on average 13L/100 (18mpg) at 65mph if I up it to 70-75mph I am looking at 15.5L/100 (15mpg). 33x12.5R20, CAI, 6.2L 8L90e 3.23. It seems to shine when im on the slower secondary roads at around 40mph, I can get it to 19-20mpg

Edited by L86 All Terrain
  • Like 2
Posted
I was getting readings of 10.5L/100km (22.4usmpg) on stock tires. When I put on my 33x12.5 10 plys I get on average 13L/100 (18mpg) at 65mph if I up it to 70-75mph I am looking at 15.5L/100 (15mpg). 33x12.5R20, CAI, 6.2L 8L90e 3.23. It seems to shine when im on the slower secondary roads at around 40mph, I can get it to 19-20mpg


Loss of mpg’s will definitely happen every time you’re adding larger tires. Considering my truck is lifted, running heavier wheels and tires, I’m definitely good with what I’m getting. Mostly depending on wind activity, I’m averaging 18-20 mpgs on the highway at 65-70 mph, 17-19 mpgs at 70-76 mph.

f26e370d717d86aadfd2d8b681589550.jpg


Sent from Above
  • Like 1
Posted

^ Yeah nice truck. Lots of members here will tell you they have a 6" lift on 35's and get 24mpg at 75mph, it's just not the case. But comparatively my current truck has about the same mileage as my old 1998 350 on 29" highway tires, and I have nearly double the HP on tap. My 2010 5.3L on 33's was better than my current 6.2L on 33's.  

Posted
11 hours ago, L86 All Terrain said:

 My 2010 5.3L on 33's was better than my current 6.2L on 33's.  

But nowhere near as fun when you stomp on the gas pedal!

  • Like 1
Posted
What do you mean flat?  What about all them hills (highway overpasses) every mile or so?  [emoji3]
 
There does seem to be a slight grade to I-95, we get less mpg going north and better heading south, generally speaking.  The grade is contrary to prevailing winds, on the east coast anyway.
Hell I can't tell. Been driving it for years between Eau Gallie and 46.

Sent from my SM-J810F using Tapatalk

  • Like 1
Posted
21 hours ago, HeySkippyDog said:

Hell I can't tell. Been driving it for years between Eau Gallie and 46.

Nice area, good times at the Titusville Rifle and Pistol Club.

  • 11 months later...
Posted

With my 6" lift and 35x12.5s I get about 22mpg at 60, 20 at 65 and about 17 between 70 and 75.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Well....I've done my first intake gasket. Probably wrong, but...we'll see?   Ultra black on the china walls and 1/4" up onto the sides of the intake gaskets. Permatex High Tack (couldn't find Gaskachinch) on the head side of the intake gasket. I read wrong and it says you're supposed to put it on the mating surface of the head, not the gasket. Hoping it's like a PB&J sandwich where it doesn't matter what side the PB goes on so long as there's jelly. That crap is messy/sticky and I got a dab or two on the intake port openings, tried to wipe it off. Hopefully it won't be a big deal and will only aid in sealing.   Per instructions I left the intake (top side) of the gasket dry except for a light smear of RTV around the coolant ports. Wiggling the intake in there was a bear but I had help to free me of surrounding wiring/stuff but I was basically able to set it straight down lined up with the bolt holes.   I did not think to wait until the RTV skinned over but there probably was 5-10 minutes while it sat before installing the intake.   Bolts finger tight first. Then, followed the Chilton's manual pattern to snug them to 15 lb-ft.   Waited a little over an hour, and then did the final torque in sequence again to 35 lb-ft.   Yesterday I replaced the fuel pressure regulator and got my new "nut and bolt kit" (fuel lines) installed. Damn GM used security torx on the spider, which I don't have, so I got scammed at the local HW store for an off-brand security Torx bit set.   The new driver's door mirror arrived yesterday, so, there's a chance this thing could be running and road legal tomorrow? I don't want to get my hopes up.   This will be my first time stabbing a distributor, too. Although, lucky me, someone else marked the old distributor for removal previously, I did see that. (Someone's been here before!!). Engine is still at TDC so it *should* be just a matter of transferring the mark to the new dizzy and rotating it into place.
    • He has his dad’s newer truck he’s put away. He has several old cars he rotates between him and his family. I’ve seen a restored square body and a SS Chevy truck he’s sometimes drives. He did raffle off a new suburban recently. As much as he is watched if he drove new stuff as a rule we’d know it. It would be fine by me. I don’t care what people prefer. I got one more new one in me. I’d rather my wife get one. I can’t get her out of the Genesis. Don’t tell anyone. I want her to get an electric truck. I want to put a generator in the back. Just because. She hasn’t bit yet.
    • Yes, you must have seen my thread on the Blazer. HOT GARBAGE, but I love them anyway. I'm convinced every car guy has a soft sport for an S/T series somewheres. Probably even a Panther too, if I'm being an honest car guy. That doesn't mean they aren't junk. And they definitely don't get better with age. I sometimes play with old cars, but that's by choice. I don't rely on them and they aren't my everyday fleet.   Derek plays the common man on Youtube and that's no doubt where he started. Now he has Youtube money (and Motortrend, etc). You think his crews and his wife ride around in old beaters when they're chasing him and his wrecks across the country? No he's got newer and nicer stuff for that, you'll see glimpses of it in the footage.
    • You refuse to own anything made in this century yet you reportedly own... a 2007 Silverado, which is now almost 20 years old. The dissonance.... turn up your hearing aid?   You clearly don't understand the government contracting process, brother. We send people to die on front lines, keep the public safe, and make people's husbands, wives, children enter burning buildings with equipment from .....wait for it.....   ...the lowest bidder....   Just because something is used for a long time doesn't mean it's good. But it might be cheap and plentiful.   Please, continue to whine about new trucks in a thread dedicated to new trucks, which you've said you'll never own. We get it. Go tell everyone how you're stuck in time on a Panther forum. I mean, Jesus, an 86 isn't even one of the good Panthers.
    • It really is comical when people don’t agree or see the reason some people prefer the older vehicles. They become condescending. All the while they may be busting their knuckles on old vehicles. I have found memories of swapping out engines in my old GM cars in a weekend without much hassle. Unlike today. One wrong move a computer will shut you down. Even on something as easy as a brake job. There’s a pretty comical YouTuber called the car wizard. A garage owner who puts it all in perspective. Another Vicegrip garage that’s shows just how tough the old stuff is. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...