Jump to content

Power window problems

Joemaggs
 Share

Recommended Posts

Joemaggs New Member

Joemaggs

Posted
Posted

I have a 2014 Chevy Silverado. My driver side window works fine. My passenger side window only works for the passenger side switch. My rear windows do not work at all. I replaced the switch and have the same problem. Any ideas I’m at a loss?

Ravenkeeper Senior Enthusiast

Ravenkeeper

Posted
Posted
2 hours ago, Joemaggs said:

I have a 2014 Chevy Silverado. My driver side window works fine. My passenger side window only works for the passenger side switch. My rear windows do not work at all. I replaced the switch and have the same problem. Any ideas I’m at a loss?

Double check the "Child Safety Switch" for the windows to make sure that it's not set.

 

Check fuses, and ohm wires from switches to window motor. 

 

 

durandetto Enthusiast

durandetto

Posted
Posted

Check the wires in the door jamb for breaks. Try grabbing the rubber boots and moving it around while operating the switches to see if they start working.

 

 

1. Test the driver's window switch power and ground feeds. 

 

2. Check for wire breaks in the door jamb boot. 

 

3. If there is low/no voltage on the Yellow wire in terminal 43 at the switch, cut the Yellow wire in terminal 22 in the X2 connector at the Body Control Module (BCM). 

 

4. Confirm there are 12 volts on the Yellow wire on the BCM side of the cut. 

 

5. If there are 12 volts, check for an open in the Yellow wire between the BCM and the driver power window switch.

 

Sent from my SM-G988U using Tapatalk

 

 

 

 

  • Like 1
durandetto Enthusiast

durandetto

Posted
Posted

You're welcome. I see that all the time at work. Probably best to add enough wire so your splices aren't in the bend.

Sent from my SM-G988U using Tapatalk

  • Like 1
  • 2 years later...
LARRY GOLLBACH New Member

LARRY GOLLBACH

Posted
Posted

Thanks for posting this topic. I had the exact same symptoms. I thought it was the switch also. Them I found this site. Found the same broken wires in the door jam harness.  Very helpful.  Thank you very much.

  • Like 1
  • 7 months later...
GOMD Enthusiast

GOMD

Posted
Posted

I have the same symptoms, but my wire harness looks good, except the thick black wire is cut and exposed some. Ordering a new harness now, hoping to have positive results.

 

Tyler Gibbs Enthusiast

Tyler Gibbs

Posted
Posted
On 3/11/2020 at 7:30 PM, durandetto said:

Check the wires in the door jamb for breaks. Try grabbing the rubber boots and moving it around while operating the switches to see if they start working.

 

 

1. Test the driver's window switch power and ground feeds. 

 

2. Check for wire breaks in the door jamb boot. 

 

 

 

 

 

 

Yup, this.

Tyler Gibbs Enthusiast

Tyler Gibbs

Posted
Posted
On 3/14/2020 at 8:46 AM, NE18 said:

Is this a common problem on the K2’s?

I know this post is from 2020 but when my 2018 was in the shop in July for this, the GM dealer said it was becoming more increasingly common.  As well as the hood sensor/switch failing.

GOMD Enthusiast

GOMD

Posted
Posted

So it ends up that while I found a slice in the black ground wire in the main door harness, I actually only needed to replace fuse #8 in the drivers side fuse panel to get everything working again. Thanks.

  • 1 year later...
Derek D New Member

Derek D

Posted
Posted (edited)

I have a 2018 Silverado. The passenger window will not roll down from the passenger door switch or the drivers door switch. All of the other windows work from their respective switch and the drivers panel. I replaced the switch and the window motor assembly (both OEM) but the problem remains. Additionally, the door ajar light is on continuously. I checked the fuses and the wiring and I can’t find any issues. Any advice? 

Edited by Derek D
Adding info
MikeBMW Senior Enthusiast

MikeBMW

Posted
Posted

Have you run a scan with a scan tool?
Also, have you checked all grounds (yeah, I know, always the easy answer without solving the problem)
Still, a scan would probably find the fault, might be a legacy code that needs a reset.

  • Like 1
  • 3 months later...
Mdp243 New Member

Mdp243

Posted
Posted

 I have a early model 2014 Chevy Silverado and the drivers side windows have stopped working as well as the stereo stays on after the vehicle is shut off (opening door does not cancel the radio) I have replaced the window switch, door wiring harness, and the latch on the drivers door. I have also checked all fuses and they are good any ideas where to look next.

  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Sdid
      2020 Silverado 1500 8speed gm needs to recall transmission

      By Sdid · Posted

      I have A 2020 1500 5.3 8 speed. LTZ. Transmission problems since 60,000 miles. Started when I go to store in morning to get my morning coffee before work leave truck running get back in put it in drive/ rev no movement step on gas a little slams into gear. Put in neutral step on gas little shake then put in gear and gose.  Shut truck off start .. ok now at stop light stop truck after a few seconds feel a little kick if that doesn’t happen stuck in 3/4 gear shut truck off wait few seconds and start usually ok again. If you down shift manually ok as long as you get into 1st before stop. If not it kicks . I WANT A NEW TRANSMISSION. Now I want a new truck it just hit 80,000 IDK IF ILL BUY CHEVY CAUSE THEY STILL HAVE THE PROBLEM AND REFUSE TO RECALL . Oh I’ve changed the fluid and filter 3 times now. And yes used mobile 1 not ac/delco cause it’s not meeting the requirements that mobile is did use ac/delco filter 
    • Chuck FB
      Joke Thread

      By Chuck FB · Posted

      Of course refrain from political debate but I myself have very dismal hope for what is all going on up here every where we turn so I nodded my head when I saw this joke.     
    • diyer2
      Navigating senior years.

      By diyer2 · Posted

      I'm looking at carpal tunnel surgery on my left hand and lumbar fusion. 
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      While waiting for parts I have been working on installing the AC compressor, new accumulator, and orifice tube. Also changed out the high side ball valve (original). The orifice tube that was in there wasn't too bad. Slightly dirty, a little bit of junk, but not blocked. Glad I changed it out.   The accumulator, which should have been a 5 minute job, may have just burned $50. Put some PAG in it, wrote the date and mileage on the side, fresh o-rings and gooey'd up the threads and rings with Nylog. Got everything connected and snugged and was going to vacuum down the system, and....   My manifold gauge won't fit on the port. It's not an R12 service port. It LOOKS like an R134 service port but the diameter is a hair too large. There's a sticker on the accumulator that says it's designed to be used with R12 and R134a systems only. So it's not R1234yf. Even if I reduced the diameter slightly with a file, the shoulder on the port is too large so the quick-connect valve won't lock on. I'm stumped. It's going back, and 50/50 on if they'll give me a refund.   Also, I did a fuel pressure test.... Key on, the gauge spikes to about 60psi and quickly bleeds off, like 2psi per second. The fuel isn't going into the plenum, no smell, starts fine, so I'm guessing there's a bad check valve in the pump and the fuel is just draining back into the tank. oh, hell. But, it shouldn't be a problem, pump primes just fine and the truck starts right up. It just means I can't really ever use fuel pressure to verify a leak at the injector or intake.
    • No F-bdy Bs
      SERCICE ESC message?

      By No F-bdy Bs · Posted

      Got this yesterday out of nowhere. Truck is a 25',6.6 gasser with 8k miles.  Only semi anomaly is that the truck had been sitting, uncranked for 6 days. Elec Stability Control showed immediately upon cranking, not while driving. No drivability issues, just the message. Battery didn't seem to be weak when cranking over.  I drove it, killed it, let it sit a few hrs with no avail.  Truck is 100% stock. No damage. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...