Jump to content

'Invisible' trailer camera calibration.

Wbrisett
 Share

Recommended Posts

MTU Alum Enthusiast

MTU Alum

Posted
Posted

The angle of the camera does correct.  The image from the trailer looks distorted/fish eye.  It needs to be rotated down about 35 degrees.  Start with the camera eye level pointing straight back, then rotate down 35 degrees.  I usually rotate the camera down until I can see the trailer, then move it up one click.  It also will not calibrate in low light situations (night/dusk/rain/snow/etc).

 

#iworkforGM 

  • Replies 34
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

MTU Alum
MTU Alum

You should only need to calibrate once.  I'll ask around see if there are any issues that may cause this.   #iworkforGM 

Plympat
Plympat

I’m new to this conversation, but going thru similar issues.  Mounted rear camera on the tail of my 30’ travel trailer yesterday, paying attention to getting it mounted on the sweet spot.  Entered all

MTU Alum
MTU Alum

Well, I got the first I heard of that.  As long as you select your trailer profile with the dimensions save in it, you should not have to recalibrate as long as you don't change a dimension or the cam

Posted Images

MikeZ65 Enthusiast

MikeZ65

Posted
Posted
On 9/21/2020 at 9:22 PM, MTU Alum said:

The angle of the camera does correct.  The image from the trailer looks distorted/fish eye.  It needs to be rotated down about 35 degrees.  Start with the camera eye level pointing straight back, then rotate down 35 degrees.  I usually rotate the camera down until I can see the trailer, then move it up one click.  It also will not calibrate in low light situations (night/dusk/rain/snow/etc).

 

#iworkforGM 

I adjusted camera and then drove about 5000 feet but progress bar never even started. Is there a way to force it into invisible so I can see how it looks other than driving around until it times out on calibrating?

 

thx again

MTU Alum Enthusiast

MTU Alum

Posted
Posted

You are getting past my knowledge.  I probably would either adjust one of the dimensions to force a calibration restart or create a new trailer profile.  

 

#iworkforGM 

Shawn T Enthusiast

Shawn T

Posted
Posted
On ‎9‎/‎24‎/‎2020 at 6:16 AM, MikeZ65 said:

I adjusted camera and then drove about 5000 feet but progress bar never even started. Is there a way to force it into invisible so I can see how it looks other than driving around until it times out on calibrating?

 

thx again

I had to restart the calibration about 5 times before it started and then drive about 4 miles before the status bar finished.  The instructions say "just begin to move forward".  Not even close for me, I tried the open road, and neighborhoods seemed to work the best to get it started and finished. 

Wbrisett Enthusiast

Wbrisett

Posted
  • Author
Posted

Calibration is a pain. Maybe @MTU Alum can comment on this, but I'm curious where the calibration is stored. I ask this because when I do get my camera calibrated the minute the power is removed (aka turn off the vehicle), I loose calibration and the camera has to go through the calibration again. I've seen some people have this issue and others don't. Which then leads me to question is this a hardware issue with the camera (some think it may be), or is this something that can be changed in the firmware of the truck itself? It seems fairly pointless to get things calibrated, then have recalibrate over-and-over again. 

sdelam Enthusiast

sdelam

Posted
Posted

Mine calibrates every key cycle, I leave the truck running when fueling to keep from loosing the calibration.

Plympat Enthusiast

Plympat

Posted
Posted (edited)

I’m new to this conversation, but going thru similar issues.  Mounted rear camera on the tail of my 30’ travel trailer yesterday, paying attention to getting it mounted on the sweet spot.  Entered all my trailer’s dimensions.  Got a good picture from the rear camera on my infocenter display in the cab.  Went to calibrate for invisible trailer view, nothing happened...  Got the display message “drive ahead to calibrate”, but no bar moving across the bottom.  Did some Google research, stumbled across some good info on myGMC.com (use myChevy.com if yours is a Chevy).  Search for “Transparent Trailer calibration”.  Why they used transparent instead of invisible is anyone’s guess.  Anyway, it says:

 

Tips

• Remove items from the back of your trailer (i.e. a spare tire, bike rack, etc.) before you calibrate the system. They can be reinstalled after you finish the process.

 

So, took off my trailer’s spare tire (which was very visible in the rear camera view when mounted) and drove around a bit, and presto, calibration started.  It’s pretty cool once it finally did get calibrated.  I then remounted my spare, but unfortunately, I ran out of time and had to store my trailer where I keep when not in use, so I don’t know if I’ll see the same issue others are having with needing to re-calibrate over and over.  Will let you know once I get it out of storage and head out on a trip next week.  


More info:  took trailer out of storage today, invisible view did not need recalibration.  As I drive home, swapped between “invisible” view and “rear camera” view.  After all the sweating over calibrating “invisible”, and despite being cool, I think the straight rear camera view is better.  More detail.  My opinion.

 

MORE More info: drove 1000 miles MN->MT on Tues/Wed, with several gas/rest stops along the way. First leg, invisible camera view worked ok.  After first gas stop, lost calibration.  Obviously, never came back...  As mentioned above in “More info”, I’m past the invisible idea, gonna stick with just full rear view.  Works great, available full time.  My truck has HUD, so everything else I need is there, leaving big center display for rear camera view.  

Edited by Plympat
MORE More info
  • Like 1
Wbrisett Enthusiast

Wbrisett

Posted
  • Author
Posted
5 hours ago, Plympat said:

Will let you know once I get it out of storage and head out on a trip next week.  

Please do.  One thing to note, I have found it calibrates better when going under 10 MPH and with something like a curb or lane markers. I'm guessing that those objects are used by the calibration software to ensure better stitching when calibrating. 

sdelam Enthusiast

sdelam

Posted
Posted
18 hours ago, MTU Alum said:

You should only need to calibrate once.  I'll ask around see if there are any issues that may cause this.

 

#iworkforGM 

I thought it was normal, appreciate any help.

migrabill Enthusiast

migrabill

Posted
Posted

I know it says go under 30 to calibrate - but mine will only do it if I'm going under 10. I find 7 MPH works best. Real pain.

MTU Alum Enthusiast

MTU Alum

Posted
Posted
On 10/2/2020 at 12:08 PM, sdelam said:

I thought it was normal, appreciate any help.

Well, I got the first I heard of that.  As long as you select your trailer profile with the dimensions save in it, you should not have to recalibrate as long as you don't change a dimension or the camera.  They mentioned that some people are pulling the rear camera into the wrong port in the bumper.  If you keep having issues, probably need pictures on transparent image, trailer, and trailer camera location.

 

#iworkforGM 

  • Like 1
sdelam Enthusiast

sdelam

Posted
Posted

Positive I am using the right port. Trailer dimensions haven't changed.  Only other thing I can think of is that I moved the camera from the roof to the correct placement on the ramp door. I did not redo the trailer profile, just assumed once it calibrated the new placement it would be good. Maybe I'll just delete the profile and start over. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • KARNUT
      Vehicle Payments

      By KARNUT · Posted

      This is interesting. My quote tagged here is different from my original quote. After I’m driving them longer. That isn’t me. I don’t talk that way. I definitely wouldn’t express myself that way. Interesting.
    • UrbanRage
      What have you done to your K2 today?

      By UrbanRage · Posted

      I have the same running boards on my truck and I do agree they are bulky. I also find myself stepping over them when getting in and out of the truck. Besides providing protection to the rocker panels, they aren't very useful.  I will be replacing them soon with the Amp Powersteps. 
    • ChristopherDobson
      Vehicle Payments

      By ChristopherDobson · Posted

      Monthly payment is only part of the equation. With today's prices and interest rates, I'd look at the total monthly cost: payment, insurance, registration, fuel, maintenance, and expected repairs. A vehicle that fits comfortably into your budget is usually the better choice than stretching for a higher trim. I've also kept my vehicles longer over the past few years. New cars have gotten expensive enough that driving one for 10+ years, while staying on top of maintenance, often ends up being the most cost-effective approach.
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      10 Ford and Chevy engines proven to reach 300,000 miles   You may note a common 3K OCI on this list of gas motors. I skipped over the diesels. Dh'O. 
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      Thanks newdude!  By the time manual selection is needed, I'm probably too much of a control-freak to depend on the transmission sensing braking to activate automatic downshifting.  I would be anticipating the situation and already be manually downshifting.   This truck replaced a 2004.5 LLY diesel with the Allison 5-speed.  Putting it in T/H made noticeable differences (when the torque converter locked, upshift points, downshift behavior).  On this 2024 gasser with the 10L1000 I haven't been able to detect much, if any, difference.  Ok, I can never tell now when the torque converter locks up.  But I also don't notice differences in shifting.  For downhills, I've probably already manually downshifted by then anyway.  Since it's also more awkward (than the 2004.5) to engage/disengage I don't even bother.  Or maybe it doesn't really matter with just a 3k lb. camper in the bed?   Thanks also for the list of reasons the charging system might select various voltages.  However, what I am seeing doesn't fall into any of those categories.  It very definitely, and very consistently, rises after coasting/braking.  Maybe not immediately, but not very long after coasting/braking.  Very consistently drops voltage when no longer coasting/braking.  It might also be interacting with the camper battery charging (I might disconnect the camper and see if it changes the charging behavior).  I also need to recheck turning on headlights for when I want to force it to charge the camper.   Another JR, in June I converted the camper to LiFePO4.  Since it's not a good idea to try to charge lithiums directly using truck, I installed a Victron Orion XS DC-DC charger (which BTW is AMAZING!!).  Being cheap, I only had to buy that one item (besides the battery, of course) to do the conversion.  The camper OEM 120v battery charger (only 19 years old and works perfectly) and the truck feed the input to the DC-DC charger (not at the same time).  But I didn't want the camper charger feeding back to the truck so I kept the old separator.  I considered replacing the separator with a 30amp diode but that means more work and might add another 1/2 volt drop.  One thing that surprised me was the voltage drop over the long 10awg wire run, so I can only charge smoothly at 8 amps (because the DC-DC charger is completely configurable).  Another reason I don't want an added voltage drop with the diode.  I might also be a little lazy but all this work is being done under the sink with a small cabinet opening.    

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...