Jump to content

FS: Elite Engineering E2-X Catch Can w/ AN Braided Lines, fittings and OE Quick-Connects

wingsaa

By wingsaa
in Classifieds (Buy/Sell/Trade)

 Share

Recommended Posts

wingsaa Enthusiast

wingsaa

Posted
Posted (edited)

I'm selling my E2-X catch can. I had this mounted in the spare battery location of my Yukon. The AN braided hoses are the correct length for that based on the 6.2L port locations not 5.3L It has AN fittings on the can and the OE gm quick connect fittings so it's literally plug-n-play. All seals/o-rings have been replaced. I'm including the clean-side separator however I don't have any of those hoses.

The can has the third additional port if you need however, it's just capped now. It also comes with the mount for the vehicle... just didn't get a picture of it. Guess I got distracted when I dumped all the oil out of on my garage floor when taking pictures. Sweet! I also updated the ball valve to a full brass as the original started to leak. This valve is more solid anyhow and should hold up better to the heat. As an added leak preventative measure, I screwed in a small hex screw into the drain port. Probably overkill but guess I got paranoid from the old valve leaking. Finally, the can isn't that purple... was just the blazing sun at my back.

 

 

Edited by wingsaa
pgamboa Senior Enthusiast

pgamboa

Posted
Posted

I can vouch for Wingsaa. Met him personally. Great guy to deal with! GLWS!


Sent from my iPhone using Tapatalk

  • 1 month later...
wingsaa Enthusiast

wingsaa

Posted
  • Author
Posted
On 10/13/2020 at 4:23 PM, pgamboa said:

I can vouch for Wingsaa. Met him personally. Great guy to deal with! GLWS!


Sent from my iPhone using Tapatalk

Thanks Bud!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Buckwild27
      Gas Prices

      By Buckwild27 · Posted

      I agree. 
    • Atlas
      Gas Prices

      By Atlas · Posted

      87 down as low as $5.14 here... winning!
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Progress... sort of.   Intake is disassembled, spider is out, fuel lines removed. Used a torch on the stripped screw with the lower intake off, much easier when I've got the intake sitting on my workbench, I made it talk. Walked right out with a pair of vice grips once it was nice and toasty hot.   New parts are piling up on my service cart waiting to be installed. Distributor, temperature sensor, new gaskets, fuel line kit, themostat, water neck.   My new pickle is I don't want to spend $600 on a replacement spider. I'm not sure IT is bad. I'm probably splitting hairs. Or it's $300 to send mine away and another 3 weeks of the truck just sitting. I have half a mind to assemble everything with the old spider to see if I can get away with just replacing the fuel pressure regulator to be safe. The obvious issue was the gushing high pressure fuel line which will be replaced. Getting to the spider really isn't that hard, and now I know what I'm doing , swapping it would be a breeze should it absolutely need one. Stupid, or smart?   The part that gives me pause is replacing the distributor. Well, it's already out. And I didn't mark it, whoopsie! Engine was at TDC when I removed it, I know that, so upon correct reinstall the metal tip on the rotor should point to the TDC mark on the distributor because that's where it was pointing on the old distributor. Worst case I'm a tooth off and have to re-stab it.   But then, what? I assume the truck will start. It doesn't appear the timing can be set. Here's the problem: These distributors can't be rotated but a degree or two, by design. What I read is Cam ****** needs to be -2 to +2 degrees, ideally at 0 (and checked/set above 1000 rpm). There should be enough wiggle to get that properly set, but checking the reported value is another potential issue. My Actron 9185 scanner says it supports enhanced GM PIDs and Cam ****** is one of them but it's unclear that I'll be able to correctly see it over OBD 1.5. I can see why people end up junking these things with life left in them. They're an absolute nightmare with tweener-year diagnostics/electronics and unobtanium parts.   Fingers crossed it starts and idles nicely. There can be hope, right? I'ma buy a lottery ticket the same day just in case.   Next steps..DO IT. I have not installed an intake before so I've been reading and watching a lot. Some say NO RTV except on china walls, some say DO RTV on water ports but not fuel/air intake. 1/4 or 3/8 bead on China walls? I think my strategy will be, obviously, RTV china walls with overlap on the gasket corners. Chapstick-style RTV the water ports. Leave intake ports dry. The only set of intake gaskets I could find locally are Edelbrock performance gaskets (uh...for an asthmatic 190hp V6? LOL) so we'll see how they do.   #NoToolLeftBehind. It took an hour, but my recovery mission for my deep 10mm socket was successful. It had rolled down the bellhousing and wedged itself between what I think are the fuel lines? I couldn't see it at all, but with a junk antenna I had laying around, I blindly went poking/sweeping for it, heard it clink, raised the truck, and caught a sliver glimpse of chrome with a flashlight way up there in Narnia. I had pushed it farther along the lines holding it captive, but within access of severely improvised tools, poking and cursing at it to finally knock it free to where I could get a fingertip on it to bring it home.    Not much to see.      
    • RyanbabZ71
      Gas Prices

      By RyanbabZ71 · Posted

      Thats crazy considering im right next door (Indiana)
    • Black02Silverado
      New Retail & Commercial Promo

      By Black02Silverado · Posted

      For a limited time, retail and commercial accounts receive an AMSOIL Vinyl Tool Tray with their order of $500 or more when they use code TRAY726 at checkout. The promotion runs through July 21, 2026.   Order at https://syntheticadvantage.com   Want to use AMSOIL in your business or sell at your store, apply here.  https://www.amsoil.com/business-opportunities/?zo=521390  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...