Jump to content

2021 Silverado 2500HD Tailgate Removal & Back On

tortiseshell
 Share

Recommended Posts

tortiseshell Enthusiast

tortiseshell

Posted
Posted

I'm looking at truck campers and it seems many of them require removal of the tailgate. Youtube has been lean with how to do this on a 2021 2500HD.  With cameras, wiring, connectors etc... does anyone have experience or advice on this? Also wondering about putting the gate back on and issues around connectors getting worn from the process.  Once my camper is on, it won't be always on.  I'll need the truck for utilitarian needs as well.  So looking for a helpful guide into the best way for tailgate removal and re-install.  Thanks so much!

ssowie Enthusiast

ssowie

Posted
Posted

Unfortunately I had to replace mine due to damage. I watched them take my old one off. It takes two people. Only took about 5 min. One guy crawled under to disconnect wiring harness and pop some clips. Then up top take out a security bolt on passenger side hinge. Finally with two people lift the passenger side up and out a little. The other guy had a screw driver as a pry bar to get the driver side popped out. That was it.


Sent from my iPhone using Tapatalk

mmmikkke Senior Enthusiast

mmmikkke

Posted
Posted

The rear camera signal and the power door lock signal run in the same harness to the distribution panel about 30" behind the driver side rear tire, on the bottom side of the truck bed floor.  You'll need to unplug this at the distribution panel and free it from whatever clips or zip ties confine it as it traverses the 30" or so toward the middle of the tailgate and crosses into the tailgate at the middle of the truck just above the bumper.  Once you have freed up and exposed this end of the harness, the rest should be obvious.  Note:  this distribution panel is in a bad place for trucks driven in mud and or salt spray.  The plug at this end of the harness is weather-protected but if you are sloppy about handling it you might accidentally let some mud or salt into the weather protected internals causing corrosion and unreliable connections "down the road."  It's the little things like this that make me do my own work, rather than pay some guy who doesn't give a hoot about what distribution panel port corrosion occurs "down the road."

 

Also there may be dummy placeholder plugs for this port on the distribution panel and you should use one to maintain the weather protection for this port while using the truck w/camper and without rear camera and power lock.  Buy a dummy plug from the dealer if necessary.  Resolve to keep this dummy plug in a plastic bag in the truck's glove box throughout the life of the truck while not in use protecting the port w/camper installed.  Similarly tape or zip tie a plastic bag around the tailgate harness connector to protect it while it and the tailgate are away from the truck.

 

CMillSilverado Enthusiast

CMillSilverado

Posted
Posted

I'm getting a new Lance 855s in May(it's on order) and after digging through a bunch of threads on the Lance Forum I can leave my Tailgate on and it will clear. I did have to put a plywood layer under the rubber matt to raise the camper to clear the angle of the tailgate. I didn't want to have to take the thing off as I did that with my old TC and Tundra and it sucked, plus these now have more weight and plugs for camera's and power. One other thing I read was that when you unplug the rear tailgate camera it affects some of the camera veiws. Anyway you might want to check the TC forum for your model to see if you have options.

Bob 3500HD Enthusiast

Bob 3500HD

Posted
Posted

I’ve got a long bed so I can get to the connector easily.  It unplugs pretty easily.  I’ve seen videos where you need to remove the spare tire on standard beds to reach the connector.  Once unplugged the tailgate come off just like any truck (not a fancy power tailgate).  I bought a camera setup to plug in and protect the plug and will mount to the back of the camper.  Chevy should have supplied a dummy plug like I had in my Ram.  I don’t think dummy plugs are even available to buy

  • 3 months later...
RND4mGuy Enthusiast

RND4mGuy

Posted
Posted

So glad I found this thread. I want to run a truck camper (TC) too and was wondering about removing these fancy new tailgates. I'd like to alternate between TC and 5th-wheel so maybe it's best to just leave the tailgate off all summer. Remember those cargo nets that everyone used to install in place of the tailgate because it was supposed to increase your gas mileage back in the day.

  • 2 weeks later...
Another JR Senior Enthusiast

Another JR

Posted
Posted

My 93 k2500 tailgate was an easy one man job. The new one is too big and too heavy for one. The first time you pull it off the driver side hinge is really tight. I didn’t use a pry tool (cringe) on my new 2021 multipro tailgate. Instead, after freeing the passenger side, my son and I rocked it up and down while applying pulling force until it finally came free. The main thing is not to smack it into the truck when it comes free. When it goes back on I’ll be applying teflon or silicone lube of some kind. 

Another JR Senior Enthusiast

Another JR

Posted
Posted (edited)

Back the OP’s original questions ...

 

On my truck if you disconnect one camera the whole network of cameras goes down. I bought the camera that goes in the tailgate ($97) and a universal FAKRA cable from Pasternack ($40 shipped) and built a housing from a 45 ell PVC fitting. I mounted it on the camper at roughly the same position and it works fine. 
 

The big connector for the tailgate is a heavy duty connector and should be good for many matings.  It just needs to be protected from dirt and water while it is disconnected.  The separate little FAKRA camera connector is less stout but was tested for something like 50 matings. If you are gentle with it I think it will last. 
 

Another issue with camper mounting is, if you use the trailer marker light circuit to power your camper marker lights, the truck detects a trailer and disables the rear parking assist system. My camper is bed length so I wanted that system operative. I ended up tying into the truck marker light circuit at the left rear wheel well marker light wire bundle and parking assist now works. 

Edited by Another JR
  • 1 month later...
KLawless New Member

KLawless

Posted
Posted

Hey there, any feedback on getting the tailgate back on? My dad and I are trying to do so now on his 2021 silverado and we accidentally latched the top before getting the bottom on...and now can't get the top unlocked/unlatched to try again -- the automated unlock doesn't seem to be working.

  • 3 months later...
dps79cj5 New Member

dps79cj5

Posted
Posted

KLawless, or anyone else, did you ever find any more information on reinstalling the tailgate? I have reinstalled mine, and plugged it all back in, but the tailgate will not open.

Another JR Senior Enthusiast

Another JR

Posted
Posted (edited)

Are you sure you properly seated the large tailgate electrical connector?  The use of the gray swing arm that pulls the connector in and latches it is counterintuitive. I had to review a youtube video and watch how the connector worked because it had been a few months since I pulled it off.    If you do it wrong it kind of seems like it seats but it isn’t really connected. 
 

Unless you are positive you did it right, I would suggest reviewing a video and then remating the connector. 
 

Edit:  Another possibility is the tailgate is locked.  Do you have the truck unlocked (not just the drivers door) or a fob in your pocket when you try it?

Edited by Another JR

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • bwiese
      on-wheel cellphone control: 2026 1500 WT (2.7L 4WD std cab)

      By bwiese · Posted

      I have a basic 2026 1500 WT  (2.7L/4WD reg cab shorttbed). Comfy, generally happy with electronics/radio - but is there a way I can add switches to steering wheel right-side position (curr. empty) so I can adjust volume, push phone button to voice dial, etc? Bill W San Jose  
    • Tyler Gibbs
      Travel Trailer 2024 2500 HD 6.6 Gas Engine ?

      By Tyler Gibbs · Posted

      The curb weight on a 1 ton crew cab long bed is around 7k lbs.  Now, I don't know where you went to school but 9k is not more than 2x 7k lbs. More than 2x 7k lbs would be 14k+.   With that said, obviously yes you're going to feel a 9k lb trailer when slowing down.  I already said, when accelerating.  When changing lanes?  No.  But if you look at the context of what was quoted, the original person said, "after a mile or two..." which means that would be after the accelerating portion and you're driving a generally steady pace.  Please do learn to read and comprehend.
    • sFrank
      2026 Silverado Range AFM DFM ECU loaction

      By sFrank · Posted

      So I purchased the Range unit for my 2026 and I am seeing different locations suggested for the ECM . Can anyone confirm wither under hood, left side or right side or behind the wheelwell?
    • No F-bdy Bs
      Dave's Auto (custom engine builder) tear down of L8T

      By No F-bdy Bs · Posted

      Like I've said before. Di and Carbon buildup is not that big of a concern. Engine had minimal buildup, and that engine was obviously not super well maintained. Do regular oil changes, and you're gtg as long as the rest of the truck lasts. Also, the High Pressure FP that people ****** about, but can't tell you why.  Now, I wish they'd trash the variable oil pump. No real world issues with them, but I'll gladly eat whatever miniscule MPG it's saving me in favor of more oil at all RPMs.    Curious to see his assessment of the 7.3 compared to the 6.6. I expect he'll praise the port inj, but from a structural standpoint, the 6.6 is as robust as any engine out there.    Not to take away from the 7.3. I feel it's equally as good as the 6.6.     As to heat on the rear cyls, I'd have to see numerous examples before I'd say it's an issue. Especially not knowing the history of that engine. For all is known, they could have blown a rad hose, and ran it hot, and the 2 rear cyls may be the first to get hot in a low coolant situation, but not be an issue aside from that. 
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      "Life is getting back to normal."    I'm driving again and all new joints are operating as expected for this stage of recovery.   My most recent joint replacement still requires a lot of attention but experience has taught me that time will quiet the remaining pain.  I joked with my surgeon that another joint replacement would take my mind off my most recent surgery and he responded by saying the next will be a hip!  There are no plans for another surgery but, unlike me, I don't think he was joking!  I certainly wouldn't refuse further replacement  if required but hope to spend time out of the "post-op"  period.  I can't stress enough that if you have been recommended for total hip, knee or shoulder replacement that you welcome the offer.  Post-op "recovery" may sound daunting and painful, however, this is far better than the insidious erosion of mobility you are currently experiencing.  Imagine what it would feel like to wake up most mornings feeling better and more mobile than you did the previous day!  Prior to my first surgery in June 2025, even getting out of bed was becoming a formidable task.  Since the day after my first surgery, I get out of bed everyday easily and unassisted.  Making the switch to feeling a little better each day rather than a little worse, is hugely motivating!

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...