Jump to content

Sun glare on center console

21AT4NJ

By 21AT4NJ
in Modifications, Wheels & Tires

 Share

Recommended Posts

21AT4NJ New Member

21AT4NJ

Posted
Posted

I can't be the only one with this issue, but when the sun is up, the trim around my center console gives off a nasty glare right into my face. Has anyone solved this issue? I have 5 percent tint all the way around, plus the sun strip. 

A08F33D5-BE27-404D-9119-DAF781586F13.jpeg

Unique_NY Enthusiast

Unique_NY

Posted
Posted

Sounds like a good opportunity to change it to a custom matte paint color or plastidip or something like that?

Grumpy Bear Senior Enthusiast

Grumpy Bear

Posted
Posted

Not the same vehicle but the same problem. I keep a shop towel handy and just cover it. On the bike I found a black powder coated part to replace the chrome. A wrap would work. 

kodiakdenali Enthusiast

kodiakdenali

Posted
Posted

I can't stand chrome. why do manufacturers put it on the interior of a car of all places? its so hard to remove from interiors because the chrome parts are often so small and difficult to remove, paint, or wrap without damage. for the exact reason you see there, it seem to be a safety hazard! I once drove a Dodge Charger that was probably the worst of all. if the sun was out no matter what direction you were traveling some piece of interior chrome reflected the sun directly into your eyes. it had this big CHARGER badge on the passenger's side dash, all chrome, you'd be seeing spots if that thing caught the sun. then just as you round the corner expecting relief the sun hits the big chrome driver's door handle and now your other eye is blasted...

 

I haven't put much effort into removing the chrome on the interior of my truck, especially because it seems to be a brushed chrome, its not quite as mirror reflective as the exterior stuff. (it still reflects the sun into your eyes just as easily as the mirror chrome though) but I'd look into a vinyl wrap or something to cover it up. no only will it solve this dangerous situation, but it would look so much better.

 

I saw a picture somewhere on this forum of someone who had their interior chrome wrapped in a matte brushed copper vinyl or something similar to that. it looked really good.

Vigilante375 Enthusiast

Vigilante375

Posted
Posted

My Camaro has the exact same issue between 12 and 1 pm.  The chrome on the dash around the gauges will blind you.  I agree that I don't know why they put these crap chrome pieces inside or outside of vehicles.  Chrome should be an extra add on and the default state of a vehicle should be color matched on the outside and brushed chrome or whatever that won't reflect the sun right into your eyes.

 

Best thing to do is get a vinyl wrap and it'll solve the issue.

1454 Enthusiast

1454

Posted
Posted

I had to vinyl wrap mine. It did it twice on the way home my first week of ownership and I remedied that this weekend. 

21AT4NJ New Member

21AT4NJ

Posted
  • Author
Posted
3 hours ago, 1454 said:

I had to vinyl wrap mine. It did it twice on the way home my first week of ownership and I remedied that this weekend. 

How did you vinyl wrap it

1454 Enthusiast

1454

Posted
Posted
15 minutes ago, 21AT4NJ said:

How did you vinyl wrap it

I took a 2  inch wide strip of 3M vinyl and then used a sharp exacto knife to trim the excess. 

kodiakdenali Enthusiast

kodiakdenali

Posted
Posted
2 minutes ago, 1454 said:

I took a 2  inch wide strip of 3M vinyl and then used a sharp exacto knife to trim the excess. 

I was thinking of asking for tips since I haven't done this myself yet. did you take any of the pieces off or do the work with them installed? many of the chrome pieces are actually separable from what's around then. the ones around the LCD screen for example are attached with screws and some melted plastic tabs. you'd have to break the tabs, but they should be able to reinstall pretty easily. I'm wondering if all of that is worth the effort to be able to wrap the vinyl around behind the piece to prevent any chrome peeking through or if its possible to do just as good a job without taking things apart. any advice?

could you post some pictures? I'd really like to see how it came out.

 

did you attempt the door handles by any chance? they will be tough due to the shape, I'm wondering if the chrome part of those can be removed somehow so the vinyl can be stretched and wrapped around the back.

gemarsh Senior Enthusiast

gemarsh

Posted
Posted
5 hours ago, kodiakdenali said:

...

 

did you attempt the door handles by any chance? they will be tough due to the shape, I'm wondering if the chrome part of those can be removed somehow so the vinyl can be stretched and wrapped around the back.

3/0 heat shrink tubing works wonders on the handles.

gemarsh Senior Enthusiast

gemarsh

Posted
Posted
15 minutes ago, kodiakdenali said:

Interesting idea, what about the open end though?

Yep, doesn't shrink closed. Yep, shiny handles are black. I tried one of those black rubber caps on the end and shrunk around it, but the handles aren't round and it looked goofier that a half closed end that you don't really see.

kodiakdenali Enthusiast

kodiakdenali

Posted
Posted (edited)

I would need to research a lot more to see what products are out there, but it appears that there at least exists some "end cap" heat shrink tubes, the largest ones here are about 4.5" long, basically a piece of heat shrink but with one end capped off instead of just open. this could be a great solution to the door handles.

 

https://www.amazon.com/Heat-Shrink-End-Cap-Pieces/dp/B00ZYTQ7A4/ref=sr_1_3?dchild=1&keywords=heat%2Bshrink%2Bend%2Bcap&qid=1618499373&sr=8-3&th=1

 

much better options than amazon:

https://www.mcmaster.com/Heat-Shrink-Tubing/heat-shrink-tubing-type~end-caps/

 

unless some company out there would be able to make a perfect fit flat black silicone cap that can be installed over the handles and easily removed if you want to sell and the new buyer likes chrome.

Edited by kodiakdenali
1454 Enthusiast

1454

Posted
Posted
I was thinking of asking for tips since I haven't done this myself yet. did you take any of the pieces off or do the work with them installed? many of the chrome pieces are actually separable from what's around then. the ones around the LCD screen for example are attached with screws and some melted plastic tabs. you'd have to break the tabs, but they should be able to reinstall pretty easily. I'm wondering if all of that is worth the effort to be able to wrap the vinyl around behind the piece to prevent any chrome peeking through or if its possible to do just as good a job without taking things apart. any advice? could you post some pictures? I'd really like to see how it came out.

 

did you attempt the door handles by any chance? they will be tough due to the shape, I'm wondering if the chrome part of those can be removed somehow so the vinyl can be stretched and wrapped around the back.

 

No, I didn't attempt the door handles, because I didn't really intend on doing a full blackout job. I just couldn't deal with the glare. You have enough of an edge that as long as you use a sharp enough knife, you can cut around the edges. I used a mini squeegee to get it laid down tight to the edge and then cut the excess. I'm by no means a professional and there are small chome gaps. But it's far more tolerable than getting blinded by the sun. Just make sure you buy a minimum of 4in wide vinyl or you will have to do a ton of stretching like me. 226418daa3a1f4f17a54b1530f999474.jpg20149e1f5f4cefe4cca72c9c37910085.jpg 

 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,902
    Total Members
    8,960
    Most Online
    whenindoubtuseahammer
    Newest Member
    whenindoubtuseahammer
    Joined

  • Who's Online   2 Members, 0 Anonymous, 335 Guests (See full list)

  • Latest Articles

  • Posts

    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      Its no wonder you've gravitated to the oil types and brands you have in later years after trying certain brands and one being a specialty oil or at least very hard to come by up here and the other would have been a commonly found oil of the era and the vastly different outcomes as a result to using the vehicles in question the same distance for an OCI . It shows what marketing hype can do without actually having the product to back up the claims and that is no different now with the insane claims that are written on the side of a bottle of oil from some of the off the shelf oils.    What has surprised me and I was already finding this out before I bought my truck with the GDI engine, that this newer fancy technology that seemingly would suggest better fuel economy/emissions with this high pressure spray of fuel is not in reality kind at all to the engine or at least the oils life. Yet they insist on claiming long OCI with this technology just like they did with the port or similar type fuel injection systems when in reality its a step back in oil life to have a GDI system.    I think the mistake your making Grumpy is that your not sending your samples to Blackstone and getting the feel good glowing report that you can run it another 1000 or more miles and then send another sample where they say run it yet another 1000 miles and on and on it goes until your sending in something that looks a lot like road tar and then they may suggest you change your oil within the next 1000 miles 😆
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      I am guessing that engines of that design back then had a better ability to be abused and survive longer than a new design engine with the long timing chain and the overhead cams and phasers etc. But I would never guess that an engine could go that far and not fail spectacularly or at least die a slow death. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      In the 80's 90's I'd run Honda's 7,500 miles between changes using Red Line HP 5W20 and do it for hundreds of thousands of miles with issues. Back in the day it was an SAE 20 with the HTHS of a SAE 30 and SN add load. It was also very polar. Oxidation VOA was over 120. Besides those motors were SPFI and lean burn tech. I could have likely run it longer but never did.    We had a Toyota bought new I ran on Pennzoil's latest and greatest synthetic of the day with "Penthane". A made up word for a very low dose of PAO. Tried 7,500 mile OCI's in that Group III/VI chemistry and the rings tapped out at 90K. Rocker box wasn't as bad as the one Punch put up but it wasn't good either. Also a SPFI motor.    I'm around 3,750 across the board on these GDI monsters and the oil it tapped out by then usually on TBN/TAN crossover and color. Red Line HP Euro.    The AMSOIL SS brochures tell you to follow the OEM values for the service class but that it can be run up to 25K if monitored. I can't imagine what motor could go that distance and not tap out. I've never owned one.    Yes, I know. Lot's of people do. I'm just not going to be one of them. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      I knew a guy in the early 80's that bought a new Monte Carlo and ran it a 100,000 miles without ever changing the filter or the oil. Just kept adding. It looked like that inside.     
    • whenindoubtuseahammer
      My First Project and GMC has me stumped

      By whenindoubtuseahammer · Posted

      Good evening. I was lucky enough to get passed down to me a 2007 GMC LBZ that was my great uncle's. While the underside and rockers are more or less gone I feel like with time I can restore it to working order since it only has 110,000 miles and he put nearly every option he could get without getting the new body style since he did not trust DEF. So far I have done everything I can think of but when I put the key into the ignition nothing happens. I put 2 brand new batteries in it. Cleaned the terminals. Check all the fuses and relays and they all pass with my multimeter. I know I'm missing something that I just cant think of. The only odd thing is the OBD2 port works which makes me think its not the mega fuse. Any advice would be greatly appreciated. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...