Jump to content

2019 new first year issues

Black02Silverado
 Share

Recommended Posts

Black02Silverado Senior Enthusiast

Black02Silverado

Posted
Posted

It seems that most at first didn't want to buy a new 2019 because of the stigma of new models having bugs.  It seems to me that those bugs are continuing into the following years as well.  Is it me or is there more posts on 21 and 22's having issues and not as many 2019's?

Phantom 4D Enthusiast

Phantom 4D

Posted
Posted
3 hours ago, Black02Silverado said:

It seems that most at first didn't want to buy a new 2019 because of the stigma of new models having bugs.  It seems to me that those bugs are continuing into the following years as well.  Is it me or is there more posts on 21 and 22's having issues and not as many 2019's?

In my opinion, there is more chatter on the newer models because they seem to make up the majority of those that comment on here. If there were separate forums for the 2019 Silverado/Sierra, there would obviously be a difference in comments. I went from a 2017 Silverado to a 2019 Sierra. Mainly because of the major problems with the Silverado.  

Wiggums Senior Enthusiast

Wiggums

Posted
Posted

It was my first time buying a first-year model (and the unusual $10,000-off promotion).. and I can say it has more gremlins than all the other cars I've owned.. with most of them being third year models.

BlancoSilverado Enthusiast

BlancoSilverado

Posted
Posted

2019, 681 truck off the Silos plant. I  have had some dumb small issues but nothing that would leave me stranded. 

about to hit 40k (miles)this weekend. 

AJ Sullivan Enthusiast

AJ Sullivan

Posted
Posted

I have 55k on my 2019.  I had back glass leak, and the parking assist has suddenly stopped working, like "light on the button is off and will not come on when I click it" not working.  Other than that, no complaints. 

SummitWhiteT1 Enthusiast

SummitWhiteT1

Posted
Posted
On 11/16/2021 at 9:01 PM, AJ Sullivan said:

I have 55k on my 2019.  I had back glass leak, and the parking assist has suddenly stopped working, like "light on the button is off and will not come on when I click it" not working.  Other than that, no complaints. 

 

Did you ever get your parking sensors fixed? I've noticed mine did that for a while and then it stopped on it's own.. but I am worried I'll have to take it to the dealer if it happens again

Elevation 2019 Enthusiast

Elevation 2019

Posted
Posted (edited)

Bought a 2019 Elevation in Sept 2019 Only issue was rear window dealer replaced it with a new one they did not even try to fix the old one. Had a 2014 All Terrain other than missing the sunroof/leather. the 2019 it is a much better truck. Nice and smooth on the highway none of the dreaded shake the 2014 had gave up on it and drove a ATS for 2 years.

Edited by Elevation 2019
spelling

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,949
    Total Members
    8,960
    Most Online
    Gkistler
    Newest Member
    Gkistler
    Joined

  • Who's Online   3 Members, 0 Anonymous, 881 Guests (See full list)

  • Latest Articles

  • Posts

    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • PunchT37
      Parking Brake - Automatic Engagement Questions

      By PunchT37 · Posted

      I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...