Jump to content

Recommended Posts

Posted

I've bought a Titan fuel tank to replace the stock one.

Has anyone else done this conversion? Installing it is not going to be a problem, But how does one change or modify the fuel filler to take large diesel truck stop nozzles. See I have this discount card that works at TA's and a few other places...

Posted
10 hours ago, Skip H said:

I've bought a Titan fuel tank to replace the stock one.

Has anyone else done this conversion? Installing it is not going to be a problem, But how does one change or modify the fuel filler to take large diesel truck stop nozzles. See I have this discount card that works at TA's and a few other places...

I've never had a problem filling my stock 3.0 fuel tank with the semi nozzles at truck stops. When I need DEF, I will stop at a truck stop to fill up diesel and DEF.

 

Have you tried using a semi nozzle at a truck stop? They do fit in the filler necks.

Posted

The big truck nozzles fit in the fill tube of a 3.0 1500 just fine. Have you even tried it?

 
You just can’t really pull the handle all the way for full flow. I just set it to the first click on the hold open device. Still fills faster than the passenger car diesel pump. 

Posted
5 hours ago, Aubie_01 said:

Is this the larger tank?  Could it be used for gas trucks?

 

Yes it is larger. I don't think it can be used for gas trucks. 

Posted

Following this to see how your DTE calculations work after the swap. I’m interested in doing this in the future as well, but nobody can seem to confirm how the DTE is affected on the 1500’s. 

Posted
6 hours ago, Jglew82 said:

Following this to see how your DTE calculations work after the swap. I’m interested in doing this in the future as well, but nobody can seem to confirm how the DTE is affected on the 1500’s. 

 

Distance to empty?

 

On my 2016 it will sit on 50 miles for awhile and the change to ‘LOW’ which is worthless

Posted (edited)
42 minutes ago, Aubie_01 said:

 

Distance to empty?

 

On my 2016 it will sit on 50 miles for awhile and the change to ‘LOW’ which is worthless

Yes, distance to empty. I meant the new T1 trucks with VIP architecture, though. Conflicting info on them out there. 

Edited by Jglew82
Posted

I’ve never seen distant to empty be accurate yet. On any brand. I set my A side to 0 on trips and track mileage on each tank. The distance to empty is always very optimistic to say the least. 

  • Like 1
  • Thanks 1
Posted
17 hours ago, Aubie_01 said:

Is this the larger tank?  Could it be used for gas trucks?

It cant be advertised for a gas truck because the gas tank is considered part of the emissions system....which cant be tampered with or parts sold to tamper with. Kinda whats going on for diesel trucks presently with the EPA hunting down vendors and tuners. The fuel tank on a diesel is not considered part of the emissions system...I'm told which is why they can sell it. BUT....even though it is not advertised as a gas tank...I am sure you can use it. 

Posted

Great thread.  From my research the fuel gauge in a gasser might re-learn the capacity of the new tank after 10 fill ups after the install.  How the computer will react seems to be the only wildcard.

 

 

Posted
On 2/16/2023 at 11:12 AM, Dirk13 said:

The big truck nozzles fit in the fill tube of a 3.0 1500 just fine. Have you even tried it?

 
You just can’t really pull the handle all the way for full flow. I just set it to the first click on the hold open device. Still fills faster than the passenger car diesel pump. 

Yup, Works just like you said.

Thanks,

SkipH

  • 3 weeks later...
Posted

Anyone that have this tank installed have any updates?  Just want to make sure fuel gauge still reads somewhat accurate or how the DTE is responding.

  • Thanks 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,760
    Total Members
    8,960
    Most Online
    MASONV88888888
    Newest Member
    MASONV88888888
    Joined
  • Who's Online   2 Members, 0 Anonymous, 1,462 Guests (See full list)

  • Latest Articles

  • Posts

    • My 2025 Silverado 1500 had to receive a brand-new engine (long block) under warranty last month at only around 16,500 miles. Before the replacement, the truck repeatedly displayed "Engine Oil Level Low" warnings, even though the Oil Life Monitor still showed around 50% remaining after about 6,000 miles since my last oil change. After seeing the warning several times, I checked the dipstick with the engine cold, and the oil level was completely normal. The next day, the message escalated to "Add Engine Oil." At first, I assumed it was just a faulty oil level sensor, so I brought the truck to the dealership. After inspecting the engine, they found internal cylinder wall scoring and ultimately replaced the entire long block under warranty. Before this happened, I was planning to install a 4-inch lift and suspension upgrade on my truck. After needing a new engine at just 16,500 miles, I honestly don't see the point anymore. I also contacted GM to ask whether my vehicle qualified for a buyback, but I was informed that it does not at this time. Anyway, this experience has left me with serious concerns about the long-term reliability of this engine. I sincerely hope NHTSA expands the current investigation or recall to include 2025 model and performs a thorough inspection of affected vehicles. My biggest concern is that these engines may fail shortly after the powertrain warranty expires. If GM truly stands behind this engine, then at the very least, please consider extending the powertrain warranty to 10 years for affected owners. That would go a long way toward restoring customer confidence.
    • Without exception but then I'm the odd duck, right? I know what goes into that test, how it is calculated and thus how to beat it. But EPA values are often not beaten by the general public and the government has in past years adjusted the means and methods to come to those values to more closely approximate "Joe Average".    The only real trick to beating that EPA average is don't drive like "Joe Average".    It's the same method you used to profit from "Economic Migration" and in doing so beat the 'stats'. But you, like me, are not "Joe Average".     The thing you don't seem to grasp is this "Purchasing Power Index" isn't forward looking. It doesn't predict what it going to be but looks backward and states what it was. They are not telling us what the THINK, they are telling us what they MEASURED. Example:    Wife says "I'm going to lose 40 pounds by Christmas". May she does, maybe she doesn't but the doctors office who weighed her when she made that statement and again at Christmas only REPORTS what the RESULT was. You and I can banter about what was possible and what aunt Tilly did till the cows come home but the result is the result. Arguing otherwise is.....irrational. That's all I'm saying. This isn't about:      What you are calling a 'Statistic' is a RESULT not a CALCUATION and as a result the RULE. Like gravity as a rule, it can not be broken. 
    • Just wanted to say thank you for posting this. Years later, your thread is still helping Silverado owners.   I bought my 2025 Silverado 1500 in January 2025, and I've had what feels like the exact same rattle since day one. After reading your findings, I believe my truck has the same issue with the cable carrier contacting the rear sliding window. To be honest, I had pretty much given up on pursuing the issue. It wasn't until I recently drove another brand's pickup that I realized just how quiet their cabin was—and how noisy mine has been all along. On my truck, the rattle happens on almost any paved road, gets even worse on rougher pavement, and I can even hear it during braking and acceleration.   I actually referenced your thread when submitting my case to GM, hoping they'll recognize this as a recurring issue instead of treating it as an isolated incident. The reason I reached out to GM first is because my dealership told me they would need to keep the truck for at least two days just to diagnose the problem. I was concerned that even after two days, they still might not be able to identify the source of the rattle before giving the truck back to me. I had also asked a few dealerships about this issue during previous service visits, but none of them seemed to know what was causing it or had a solution. That's why I decided to contact GM directly first, hoping they might already have an official repair procedure or guidance for this issue.   I also hope GM eventually comes up with an official fix for this problem. I have a feeling there are many Silverado owners experiencing the same rattle, but most either choose to live with it or simply don't know what the cause is.   Really appreciate you taking the time to document your diagnosis. Your post is still making a difference years later.
    • I have 2 choices. 
    • Do you have access to BP fuels? Some stations have Silver 91 E-0 priced the same as their 93 E-10.  There is a local Marathon with 90 alky free for $6 a gallon but I go down the road to BP for $5-ish. They also have a 100 E-0 but that stuff is $10 a pop. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...