Jump to content

Recommended Posts

Posted

Recently my battery has died at random times.  Sometimes it cranks slow and starts, other times its dead.  It started and i drove about 35 minutes to the store, came out less than 10 minutes it was dead.  Jumped it and drove home it sat over night and started fine.  It does it randomly and nothing is staying on, and i dont have any accessories hooked up to drain in.  Could this be the battery? Or the alternator?  Its been like this for over a month

Posted

Yes, it could be the battery or the alternator.

Take it an AutoZone, or O'Reilly, or any auto parts store and have them check the battery.

Posted

Sometimes it cranks slow and starts, other times its dead.

First time would be the last time. 

Posted

Have your charging system tested under a load and if the amperage is up to spec. then replace the battery. AC Delco and Die Hard are good brands to consider.

Posted
 
#PIT5985A: Diagnostic Tip: No Start/ Ignition Will Not Turn ON/ No Power Due To A CAN bus 2 Issue/Lightning Strike/ Failed Over The Air Update - (Mar 6, 2023)
Subject:  Diagnostic Tip: No Start/ Ignition Will Not Turn ON/ No Power Due To A CAN bus 2 Issue/Lightning Strike/ Failed Over The Air Update

Involved Region or Country

North America

Condition

Some technicians may experience one or more of the following concerns: 

  1. No Start
  2. Vehicle will not crank
  3. Vehicle will not enter into Key On, Engine Off mode (Service Mode)
  4. Vehicle's Instrument Panel Cluster will not Illuminate
  5. Vehicle will not shut Off. 

In addition to the above concerns, when using GDS2 to connect to the vehicle, the pop up message seen below will be displayed, prompting to turn the ignition on, but the ignition can not be turned on.  In some cases, after several ignition button presses, the ignition may turn on. Then, the customer or dealer technician may notice that blower motor turns on at a higher speed and then the ignition will not be able to be turn Off.  

Cause

This may be caused by either an issue with Can Bus 2, the vehicle received an "Over The Air" (OTA) update that has failed/ or the vehicle's electrical system was damaged by a voltage spike such as a lightning strike or an incorrect jump start procedure.

Posted
On 3/28/2023 at 2:08 PM, 20silverado20 said:

Recently my battery has died at random times.  Sometimes it cranks slow and starts, other times its dead.  It started and i drove about 35 minutes to the store, came out less than 10 minutes it was dead.  Jumped it and drove home it sat over night and started fine.  It does it randomly and nothing is staying on, and i dont have any accessories hooked up to drain in.  Could this be the battery? Or the alternator?  Its been like this for over a month

#23-NA-023: After A Remote Start When The Start Button Is Pressed The Engine May Stall or Will Not Restart - (Feb 28, 2023)

Subject: After A Remote Start When The Start Button Is Pressed The Engine May Stall or Will Not Restart

 

 

volved Region or Country

America, Uzbekistan, Middle East, Russia, Israel, Palestine, Bolivia, Chile, Colombia, Ecuador, Peru, Japan, Kazakhstan, Korea, Thailand

Additional Options (RPOs)

Condition

Some customers may comment that after using the remote vehicle start, either from the fob or app, they experienced any of the following issues:

When they enter the vehicle and press the start button the engine stalls

If they try to restart the engine, it will not crank

If the remote start times out they are unable to restart the engine with the start button

When trying to turn engine off the engine stays running

Unable to turn the ignition off

Service Steering Column Lock Message, if equipped

Dead Battery

Cause

The cause of the condition may be a Body Control Module (BCM) messaging issue.

Correction

Reprogram the BCM following service information instructions to update to the newest software level.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • On 2021 3500hd it consistently sets automatically when selecting park if the incline/decline is above a certain angle. 
    • Curious, did anyone ever get a fix for the vibration reported here.   I have a 2024 Silverado with 6.6 duramax.   I’m noting the same vibration resonating up through the steering shaft into the steering wheel.    Best way to describe- like someone is tapping on the steering shaft/components and it’s resonating into the steering wheel.    thanks. 
    • Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • 2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...