Jump to content

Lower ball joint stuck

Bryant Wray
 Share

Recommended Posts

Bryant Wray Enthusiast

Bryant Wray

Posted
Posted

I am trying to replace lower ball joints on my 2014 Silverado 1500 Z71. The drivers side is very stuck. I have broke everything else loose, I just cannot get the lower ball joint busted loose from the steering knuckle. I have tried the tuning fork and the separator clamp. The clamp does not expand far enough to track the bottom of the ball joint stud. Any ideas? This has been too many days trying to figure this out. 

5A462E77-C321-439F-B21F-6E4975D5CEDB.jpeg

717579F6-4C38-4780-A569-BA13D904B69B.jpeg

F87E5CC6-CA37-47E0-BEFD-CD7BAB273A6C.jpeg

  • Sad 1
CamGTP Senior Enthusiast

CamGTP

Posted
Posted

Heat the knuckle with a propane or map gas torch. You likely need to expand the metal that is around the ball joint stud. Do that for a while to get it nice and hot, then use a ball joint fork to try and get it out.

  • Like 1
richard wysong Senior Enthusiast

richard wysong

Posted
Posted

Strike the side of the knuckle adjacent to the taper with a large hammer and that will pop it, may take multiple blows

  • Like 2
  • Thanks 1
mikeyk101 Senior Enthusiast

mikeyk101

Posted
Posted

Another agreement on a BFH. I used a mini sledge when needed and several real strong hits on the side always got it separated for me. Don't hold back and whack it good.

  • Like 1
Bryant Wray Enthusiast

Bryant Wray

Posted
  • Author
Posted

Used a 4lb sledge, didn’t bust it loose. Any other ideas? I got a ball joint separator from the parts store but the notch is not wide enough to go around the ball joint. Do they make bigger ones?

Buckwild27 Enthusiast

Buckwild27

Posted
Posted
18 minutes ago, Bryant Wray said:

Used a 4lb sledge, didn’t bust it loose. Any other ideas? I got a ball joint separator from the parts store but the notch is not wide enough to go around the ball joint. Do they make bigger ones?

Air hammer. 

  • Like 1
txab Senior Enthusiast

txab

Posted
Posted
27 minutes ago, Bryant Wray said:

Used a 4lb sledge, didn’t bust it loose. Any other ideas? I got a ball joint separator from the parts store but the notch is not wide enough to go around the ball joint. Do they make bigger ones?

How wide is the notch? Mine is at least 15/16" wide

  • Like 1
richard wysong Senior Enthusiast

richard wysong

Posted
Posted

7/16? That makes no sense, 7/8 maybe? Sounds like you got a tie rod fork, return it and get a BJ fork

  • Like 2
Bryant Wray Enthusiast

Bryant Wray

Posted
  • Author
Posted
10 minutes ago, richard wysong said:

7/16? That makes no sense, 7/8 maybe? Sounds like you got a tie rod fork, return it and get a BJ fork

Correct, 7/8, my mistake

  • Like 1
swathdiver Senior Enthusiast

swathdiver

Posted
Posted
On 4/8/2023 at 10:57 AM, Bryant Wray said:

I am trying to replace lower ball joints on my 2014 Silverado 1500 Z71. 

 

Stop by my house and borrow my J-43631 and torture yourself no more.

Kent Moore Ball Joint Puller Tool J-43631 (cs1354 802 B3 for sale ...

 

 

 

  • Like 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,942
    Total Members
    8,960
    Most Online
    tblt44
    Newest Member
    tblt44
    Joined

  • Who's Online   5 Members, 0 Anonymous, 822 Guests (See full list)

  • Latest Articles

  • Posts

    • C/K Man
      Silverado 4500-5500-6500 are they still being produced? Would have sold better as GMCs as well

      By C/K Man · Posted

      There was talk over the last couple of years that the contract to build these trucks between GM and International would not be renewed.  International moved production of all their other trucks besides the companion CV model out of the Springfield plant some time ago when they opened their San Antonio plant.  That left Springfield only building the Silverado Medium Duty, International CV Series, and some Express/Savanna long wheelbase cutaways.  International also put the plant up for sale some time ago.  This all answered my earlier question as to why GM and International did nothing with these trucks since they were introduced, as they had basically become a market 'placeholder' with a finite life.    The Silverado Medium Duty/International CV trucks were interesting combination of a GM powertrain, electrical system, and K2XX Silverado cab with an International chassis that was supposedly designed for a step-van type vehicle they never produced.  They were manufactured in International's Springfield plant along with the IH MV series initially.  When first introduced, there was much talk that the Silverado Medium Duty/CV would eventually get a gasoline engine option along with other upgrades and GM and IH would work on a class 6/7 joint venture truck.  This was before VW bought Navistar out, after that happened no more was said.  Draw your own conclusions...   About the time talk started that the GM/IH joint venture was not going to be renewed, rumors started that GM would develop a new line of medium duty trucks themselves.  The story is the new trucks will be part of the next generation HD's due in 2028, and will still feature a 'straight rail' chassis design that the current medium duty has.  GM views this as a desirable feature that differentiates their truck from the competition.  A gasoline engine option is also expected.  As the current Silverado Medium Duty remains in production until September 2026 and there is still a lot of inventory available do not expect any official word for some time.   I believe GM remains committed to their successful partnership with Isuzu, and all the LCF models will still be available from Chevy Commercial dealers.  Isuzu is on the cusp of opening a new large plant in South Carolina and there is also speculation that this may result in new product for both Isuzu and Chevy Commercial dealers.                  
    • davester
      push to talk button

      By davester · Posted

      drive the truck back to the dealer and complain that the button works.
    • davester
      push to talk button

      By davester · Posted

      drive the truck back to the dealer and complain that the button works.
    • nfisherman
      Software Update

      By nfisherman · Posted

      I have a 2026 2500 HD Ultimate. My phone app says there’s a software update available. It’s something about improved battery management and something to do with the running boards. I follow the instructions for the update but the “Check for Updates” option is greyed out in my settings menu. Has anyone else seen this? How did you resolve it? The help message just says “see your dealer” if the download doesn’t work. I’m just trying to save a trip. 
    • newdude
      Exhaust Question

      By newdude · Posted

      Fuel mileage?  That's all how you use your right foot.  Exhaust will give you sound.   Stock exhaust 5.3 is 2.75" diameter piping.     If the truck is nice and worth putting some $$ into it, I'd go for a Corsa catback.  I had one on my 2019 old body 5.3 and it was just perfect.  Zero drone, just driving around and cruising on the highway you'd think it was stock, but when you opened it up it was like a Camaro with the factory dual mode.  Corsa bumps their catback to 3in diameter.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...