Jump to content

22' Custom build

Vincej138
 Share

Recommended Posts

Vincej138 Enthusiast

Vincej138

Posted
Posted

Hey all, just got my 22 last month. Found one of the last ones on the lots in AZ and got a screaming deal. Ive made it all of about 1200 miles before my past life couldn't handle having it stock anymore. Grew up in the desert and raced off-road for years in 1450 and Class 5-1600, worked in the industry and finally settled down behind a desk when we had some kiddos. Im not going full long travel on it, its the family cruiser. But itll look good and hopefully I can help anyone along the way.

 

22 Custom 2WD with the 2.7L turbo which has been a very pleasant surprise. 

20230616_113545.thumb.jpg.135c74d1a3ab3c6f3c3403442f47a227.jpg

 

Here's the plan and whats been done/ordered already.

 

Performance:

-AFE Momentum intake w/dry filter

-AFE Bladerunner hot/cold charge pipes

-Stillen CAI valance/scoop - backordered

-Black Widow race venom muffler with resinator delete. Ill do that after the above is in, just waiting on the valance. 

 

Lights/appearance:

-Lasfit LED High and Low beams - These made a huge difference. PITA fit, but so much brighter.

- Black badging/lettering

- Full cover floor mats and underseat box

- Stubby antenna

 

Suspension: 

-CST Fabricated 3" lift spindles

-Bilstein 5100s set to .5" lift, maybe 1"

-Bilstein 5100s rear 0-1"  

-1" lift block maybe. See how it looks w/o

My truck sits 2" nose down stock, and eventually will go full coilovers and an upper arm, but with only really .5" of lift being put on the upper geometry those can all wait a bit.

IMG_20230801_225809.thumb.jpg.ccd9423610e937bfeda1d87f2ce4f15f.jpg

 

Tires:

Im still deciding here but narrowed down between

35x12.5R17 Kumho AT52s

Or

315/70R17 Toyo AT III's

Wheels:

Torn between these... Both -12 offset

17x9 Vision Wheel M2 overlands inGrey

17x9 Visiom Wheel Ojos in Black/Grey

 

Ill get photos up as stuff comes in and on. For the motor, im not expecting HP gains, im just trying to get the turbo spooling about 500rpm sooner and have a good sound, maybe make up some mpg. But i love the motor and it flys up the mountains when we go out of town while getting 20mpg+

 

Its absolutely hot as balls here, so I womt be installing anything for another month or so, just cluttering my garage. 

 

Ill do as many photos and notes as I can. Ive got a pretty good grasp on all things suspension wise, so feel free to ask any questions. 

  • Thanks 1
Gangly Senior Enthusiast

Gangly

Posted
Posted

Congrats on the beautiful truck.  If you can, I would suggest new front end suspension (Eibach or Bilstein) and an immediate alignment.  The front suspension on the 2WD generally ages quickly and the camber can go south on you even quicker, wearing out the inside of your tires prematurely.  Just something to keep an eye on.

 

Again, congrats on the beautiful truck I look forward to reading about your build.

Gangly Senior Enthusiast

Gangly

Posted
Posted

Also, check 4Banger on this site, I believe he has a 2.7 as well and has done quite a bit to his truck.

Vincej138 Enthusiast

Vincej138

Posted
  • Author
Posted (edited)
1 hour ago, Gangly said:

Congrats on the beautiful truck.  If you can, I would suggest new front end suspension (Eibach or Bilstein) and an immediate alignment.  The front suspension on the 2WD generally ages quickly and the camber can go south on you even quicker, wearing out the inside of your tires prematurely.  Just something to keep an eye on.

 

Again, congrats on the beautiful truck I look forward to reading about your build.

 

Thanks!

 

Yup, i already have the lift spindles, and front/rear Bilstein 5100s in the garage. Then down the line a bit ill change out the upper arm for Icon or Mazzula and some coilovers. 

 

Im using the spindle to get the lift without having to preload any coil if any at all. This should keep the best possible ride quality with added track width and ground clearance. The lift spindle just drops the hub mounting location down and doesnt change any of the upper/lower arm geometry. The .5" or so ill have on the front Bilsteins will need an alignment though. 

Edited by Vincej138
Vincej138 Enthusiast

Vincej138

Posted
  • Author
Posted

So I am gonna give the Kumho AT52s a try. They are very similar to the first and second versions of the Toyo AT's which I loved. And they are considerably lighter, so if i can keep close to the same weight as the stock generals and 20s im all for that. 

 

Weve been under 110 deg. here for a few days so hopefully can get back to getting some stuff done on it as all the 5100s showed up so lift is all here. 

 

Adding pics of both spindles and the LEDs i went with. 

20230806_213139.thumb.jpg.a97fb18b2f05a9bf0c8ac5c823504e49.jpg

20230806_212817.thumb.jpg.e9c7247eed8cd2b45f5591c958cd9324.jpg

  • Like 1
Vincej138 Enthusiast

Vincej138

Posted
  • Author
Posted
22 hours ago, Bikerjon said:

Are those LEDs Lasfit Pros?

 

They are. I kinda went round and round with them, when you buy the High/low set, they sent me two sets of the H11's and not a H11  / 9005. Their position is that its the same mounting per bulb and just no reflector on the highs. Which is correct, but normally the 9005's have a diff lumen rating. I got the low's in already and I love them. Still need to put the highs in, but they are def not the easiest fit. I found that if you remove the O-ring from the stock bulb and swap it, they do go on a bit easier. Ill get the highs in this weekend and report back.

Vincej138 Enthusiast

Vincej138

Posted
  • Author
Posted
7 hours ago, Low Elevation said:

You should lower it since its a Rwd. Would look sick!

 

Only thing I've ever lowered was my old 67' bug!

  • 1 month later...
Vincej138 Enthusiast

Vincej138

Posted
  • Author
Posted

Wheels/tires will be in next week. 

 

17x8.5 KMC Canyons in black

315/70/17 Nitto Terra Grappler G2's

 

Then can finally get everything on

Gangly Senior Enthusiast

Gangly

Posted
Posted (edited)

Looks good, that's a lot of sidewall on those 34"+ tires, I like it!

 

Edited by Gangly
Vincej138 Enthusiast

Vincej138

Posted
  • Author
Posted

Finished it up last night. Need to swap the silver bagdes out still and the intake/charge pipes. Added a black tip on the exhaust as well. 

 

With 0 preload on the 5100s, it rides great and upper is in same position as stock at ride height.

 

Before

20230923_150212.thumb.jpg.1bf8c1af7d0535d3619d27f9251328e9.jpg

After

20230923_233411.thumb.jpg.06b04a5fd2591eaea95fcf3887596c6c.jpg

 

20230924_121128.thumb.jpg.552a76b932822d4c76c286d74572067c.jpg

 

20230924_115919.thumb.jpg.563b40df73e78220eda9c28265679299.jpg

 

 

  • Like 1
Vincej138 Enthusiast

Vincej138

Posted
  • Author
Posted

Also, for anyone looking to do the fronts on their own, but scared about losing 3 fingers....this is the compressor I used. It felt much more stable and stronger than the typical ones you can rent from Autozone, and the bridge helped keep things even side to side. At no point did it feel like it was gonna pop or even bow any. I also just used some grease/lube on the threads to keep it smooth. Also, have a good pair of vice grips to hold the end of the shock shaft or a pass through socket.

 

https://www.amazon.com/BILITOOLS-2-Piece-Compressor-Macpherson-Load-2645LB/dp/B09PYR6NVF?th=1

 

On the front it started at 22" hub to fender lip. Its at 25" now, so the #1 notch on the shock with a 2.7L will be true stock setting as the spindle is giving the 3" of lift. I also used paint pens to mark centers on the spring seat and cap to keep all that aligned for re-install on the 5100's, then again for all the bolts to do an easy check for anything coming loose. 

 

Getting an alignment check today. Drives straight and true, but steering wheel is slightly left

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • davester
      Bench seat swap for 2021-2024 suburban

      By davester · Posted

      probably won't get a response from that user, as they haven't returned to the site since making that one post.  users don't (at least I don't, and I haven't seen any setting which would notify me via say, email) get any notification other than going to this site, and checking if they got a response on their thread...
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Thanks - I wasn't quite caffeinated this morning. 2:1 makes sense, turning the crankshaft 360 degrees will turn the cam 180 degrees, and had I done that, the cam's dot would be at 6 and the crank's at 12 again.   I went ahead and took the sprocket off anyway, aligned everything dot-to-dot including the balance shaft just for s&g. I'm glad I did because I discovered no Loctite on the timing sprocket bolts. Maybe it's not required, but at only 20 ft-lb torque spec, those bolts aren't in there very tight. Cleaned and reassembled with some thread locker and torqued.   A general observation: Less is more with RTV. If a little doesn't stop a leak, a LOT probably won't, either. RTV is thinly veiled revenge, in a tube...      
    • richard wysong
      Wow I'm in a pickle. (Broke down truck) and a story.

      By richard wysong · Posted

      The timing marks are ok, that is #1, you can turn it over until they line up and it won't change anything, the crankshaft turns twice for every camshaft revolution, I have always set up SB Chevs as your pic shows using a straight edge
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Someone's been here before.... There is a receipt for a 3-piece timing set, purchased earlier this year.   Is this picture something, or, nothing?   I have the timing cover off and my crank is perfectly TDC and the keyed gear's locating mark is dead on 12 o'clock.   The cam gear locating mark is also at 12 o'clock. Now, I'm not an expert, but all the install guides say the two locating marks should meet and be perfectly aligned when installing a timing set. The mark on the crank should be dead on 12:00 and the cam gear's mark should be dead on 6:00, and both marks should be perfectly vertically aligned.   I believe the timing gear is keyed or has a dowel that ensures it can only be installed on the cam in one position, so I have to believe the cam is out of phase somehow. At the very least, with a triangular bolt pattern, it can only be installed in one of 3 different positions.   Before I pulled the front cover, the truck was running alright, no service engine soon lights except an occasional P0172 / rich condition. Timing -16 timing at idle (should be +16), and total -35% fuel trim, two conditions I haven't been able to figure out.   In related news, my injector tested pretty well, wasn't leaking, but I had it rebuilt anyway, and it's on it's way back to me.         Along with this discovery, the good and bad:   Good: The oil pan seal appears undamaged.   Bad: -The timing cover has been reused, and the positioning dowels have been broken. That could explain some of the leaking. -Some kind of white paste or grease was used to try to seal the oil pan seal and timing cover (since wiped off..). -Then, someone globbed silicone all over the front of the cover and also buried the ckp sensor in it. But, they didn't put any inside the cover or use RTV to try to seal the oil pan seal with the timing cover (good).
    • Grumpy Bear
      PF63 Oil Filters Going Away?

      By Grumpy Bear · Posted

      The guy that owns K&P filters last I checked in with him has over 300,000 miles on his Dodge base Hemi using his own 35 micron absolute stainless mesh filter from its first oil change.    The GM study I've posted a dozen times shows the relationship in engine life based in multiples of base units, not miles or years. That is the base unit is the number of miles the motor ran using the reference filter efficiency.    The above two paragraphs dismantle anecdotal arguments IF one changes oil often enough to prevent particle formation and the motor is in otherwise good shape. That is not full of silica (no air filter) or suffering a metallurgical issue that is not part of the lubrication discussion. Poor heat treat in example.   Data from UOA's I've reviewed from more than a few engines can show remarkably broad variations in oil cleanliness using the exact same filter over the course of an engines life.     Lastly there is the common sense of it. Wear debris WILL circulate the engine BEFORE it ever sees a filter in route to that filter and WILL harm the pump which NEVER sees filtered oil.    Alpha question then becomes, given the facts, how long do you believe is a reasonable service life from a vehicle you are certain you will not pass down? That is the junk yard will be it's resting place when you're done with it? (the moral issue most don't care about).    Omega question is then how diligent are you prepared to be in general mechanical, air & oil maintenance? Preventing particulates and keeping them sufficiently dilute; preventing the precursors from generation, amalgamation and precipitation.    If I get a good look at the engine bay of a vehicle I have a fair idea of the owners commitment to the inside of the power train. That 30 micron WIX is still more efficient than a sieve.                 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...