Jump to content

Front grill replacement?

Nick Taylor

By Nick Taylor
in Modifications & Accessories

 Share

Recommended Posts

Nick Taylor Enthusiast

Nick Taylor

Posted
Posted

Thinking about trying to replace the chrome grill / bumper on my 2021 Denali 3500 with the AT4 version. Anyone attempt this? Doable or major truck surgery?

BuckWallace Enthusiast

BuckWallace

Posted
Posted (edited)

Take a look at this:

 

 

Doesn't look super easy, but it also seems doable. I was trying to replace the AT4 badge on my 2024 AT4 grille and decided against it (the badge is really tucked in there), but if I was replacing the whole grille I'd definitely give it a shot myself.

 

Not sure how much more work the bumper is, but I'd imagine once you get all that trim off it's probably not too difficult.

 

 

Edited by BuckWallace
Nick Taylor Enthusiast

Nick Taylor

Posted
  • Author
Posted

Wow @BuckWallace, thanks for sharing. I think the chances of me doing that without breaking one of those little clips isn't very good. All the same, I have a camera I need to replace (the front camera on my 2021 Denali is cracked) so I may have to at least lean the grill back. Was wondering how hard it would be to completely remove and swap it out.  This video helps alot!

KTDanforth Enthusiast

KTDanforth

Posted
Posted

I think the Video, is making it look harder than it is.  I have Chevy and Not the GMC but I suspect they set them up the same way.   I can drop my grille and bumper in about 30 minutes.

 

GMC guys correct me If I am wrong here.   On the chevy the left and right side trim under the head lights can be popped out from the center and left alone not detaching from the left and right wheel wells.  I am assuming this is the case with the GMC.

 

If this is case all you have to do is follow the grille detachment instructions and leave the lower trims attached but pull them back so you can get to the lower bolts on the grille.

 

As far as the bumper goes.  it is held on by 4 bolts on the top and to on the bottom.   just be sure to unplug the electrical first.

 

Good Luck, it is not as hard as it looks.

 

Kjduvall Enthusiast

Kjduvall

Posted
Posted

its really not that hard, the side moldings are the trickiest part ust take your time. i did it and the hood piece cause they wouldnt make a reg cab at4, so i made my own.20230722_131831.thumb.jpg.a1340c38e7d2ea0d9ad493acf03a867c.jpg

  • Like 1
Nick Taylor Enthusiast

Nick Taylor

Posted
  • Author
Posted

@Kjduvall that looks really sharp. Where did you get your parts? Straight from dealer, or did you find take-offs from an AT4? Wondering how much of an investment this is, and how hard it is to get the parts (mostly interested in grill and front bumper treatments).

 

For some reason I don't have the option to like or reply to posts...perhaps because I just joined?

Kjduvall Enthusiast

Kjduvall

Posted
Posted

yep dealership parts the grill was just under 800 and the nose piece was under 200 bucks, the bumper (stock chrome) was sand blasted and powdercoated black (my buddy owns a powdercoat place so it was free). but i dont recomend doing that, one small hit in a lowes parking lot and it chiped rather easily. when i do the bumper "skin" again im going to look for a non chrome bumper and have it painted with oem paint i think itll hold up better.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Z45
      Towing In Loose Gravel

      By Z45 · Posted

      Having owned 4wd vehicle since the 1970s I find there are varying opinions on how to use 4wd, every owner is an expert in their minds.  IMO, 4LO is the appropriate gear and what I would use,  You have to feather the gas to avoid spinning tires and the lower the gear the better chance.  But like I said you will find those that think their method is best.  I live near a boat launch.  Yesterday there was a new Ford Maverick pulling out a pontoon boat almost 2x its size, they had no problems and they don't have a LO range.   True story. One winter day not long ago I was coming out of small town post office and there was a F150 4wd parked in front and was stuck foot deep snow ruts. I knew the lady so I asked her to put it in 4wd (wondering why in the middle of a 2-day snow storm she wasn't).  Her reply surprised me, "my husband" (the expert) told me not use that because it uses too much gas. She finally got unstuck spinning in 2wd which likely used more gas than not.  
    • dna9656
      New to Me 2010 SLE (Quirks, Issues)

      By dna9656 · Posted

      Your tire pressure issue may just be batteries, you can reset them using tge Ing switch (I think) and the owner's  manual. ChatGTP will b e a faster, better help than Google.
    • Another JR
      Towing In Loose Gravel

      By Another JR · Posted

      The thinking is that starting out in a higher gear makes it easier to avoid applying excessive torque when pressing the gas pedal. In a modern 4wd truck with 4 low and a limited slip or locking rear end, I would use 4 low and try to crawl up the ramp. Sometimes if they are too slippery, you have to back up to let the boat have some bouyancy, and then accelerate briskly to get some momentum to help you pull the through the slippery parts. 
    • XY74
      Roll up bed cover experiences

      By XY74 · Posted

      I have a Retrax pro that I first had on my 2020 chevy and transferred it to my current GMC.  It stays in the garage most of the time, so hard for me to judge it's long term weather resistance.  It still works perfectly, been very durable.  It doesn't see oil patch usage, but it's not a mall queen.  It keeps most things mostly dry (small leaks) and the security of it is enough to slow someone down but not keep them out for long.  I would buy one again, it works for me.     
    • fm2176
      New to Me 2010 SLE (Quirks, Issues)

      By fm2176 · Posted

      Thanks to the convenience of Amazon, I was able to get a few things done to the truck today.  I installed Carquest Premium oil and air filters with five quarts of Mobil1 High Mileage 10-30 along with a quart of Pennzoil Platinum 5w-30 I already had.  The latch for the flip up center console lid was broken so I replaced it along with the power mirror switch.  I found my push retainer assortment this morning and reattached the plastic under the bumper and it was only held on with a few screws and retainers.  Then I programmed a new remote keyless entry fob so I can lock my dog in the truck when I take her out with me (I've got to keep the air going for her since it's been in the 100s).  Finally, I ordered some LED interior bulbs and replaced the reading lamps.  The front lights are working fine while one of the back lights only works intermittently and the other not at all.   While under the truck, I found the source of at least one of the noises: the sway bar links need replacing.  I ordered a set of Suspension Dudes links with Code Red bushings.  Never heard of them, but they're made in the USA and have decent reviews.  While making yet another Amazon order, I went ahead and added a set of front tow hooks.  I went with red, since that's the color of the sway bar link and bushings and it should look decent enough on a black and chrome truck.  Speaking of which, it doesn't bug me much, but the passenger side mirror has a chrome cap while the driver side doesn't, so eventually I'll make them match one way or another.  Oh, and I ordered a $20 TPMS reset tool.  No idea if it will do anything for my sensors but it was cheap and will work for the Ford Transit Connect as well.     For tradition's sake, I ordered a new oil change wrench.  I kept the Snap-On 9/16"x15mm GM wrench I bought when I was 18 in the 2006 GMC from the time I bought that truck until the truck was lost.  While I was tempted, there's no need to spend $80 for a new SO wrench, or even $50 with shipping for a used one on Ebay.  I just bought a Duratech 15mm extra-long ratcheting wrench to do the job as needed.  It works, and if I like that wrench enough, I'll buy the set.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...