Jump to content

2001 chevy silverado security issue.

Tiffanyrose
 Share

Recommended Posts

Tiffanyrose New Member

Tiffanyrose

Posted
Posted

Truck always things it's being stolen, engine cranks but it won't fire up and securty will flash. It actually starts flashing as soon as you open the door for the truck and they key isnt even in it yet. Sometimes it will start perfectly fine, but most of the time it will not. I've don't alot of research over time, this is for my dad's truck and it's been a problem for over 10 years but it has gotten to be alot more frequent.  I've been told about the chip key and the relearn process, however the key that we have does not have a chip in it.  which leads me to believe the relearn process will do nothing no matter how many times we do it. Ive read about the passkey resistor, the total bypass with the ignition wires, and about the ecm box replacement. Im wondering though since we dont have a chip key, which is the most  logical part to buy?   So if anyone out there can point us in a good direction I would really grateful!

dna9656 Enthusiast

dna9656

Posted
Posted

Our local Ace Hardware made a chip key for my 2015 Silverado for$100.00; that's a lot less than the dealer. I suggest you give them a call and have your VIN,title, and/or registration with you.

davester Senior Enthusiast

davester

Posted
Posted

ouch.  that is SUCH a ripoff, as the blank key w chip retails for under $20...

 

It would be somewhat reasonable if you don't have any key for the truck, so they need to program the new key as the master key for the truck, but somehow I think they would charge extra for this...

richard wysong Senior Enthusiast

richard wysong

Posted
Posted

If it didn't have a chip in it it wouldn't have a security system. Do the relearn or get someone with a tuner to shut the system off

Tiffanyrose New Member

Tiffanyrose

Posted
  • Author
Posted

I had it tested at the hardware store, and it showed no chip. He went out to started the truck today and it wouldnt fire. He waited an hour then tried again, and it started 3 times. In a row. My 2000 cavalier did not have a chip key, but still had a security system.  🤷‍♀️

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Zane
      2027 Chevrolet Silverado: Official Discussion

      By Zane · Posted

      It's official. Chevy pulled the covers off the next-gen 2027 Silverado 1500, and we got the first official look.   Full breakdown here: https://www.gm-trucks.com/2027-chevrolet-silverado-official-first-look-specs/   The quick hits: LT is dead. The new core trim is just called "Silverado." Two new V8s, a 5.7L and a 6.6L. No horsepower or torque numbers yet. The 2.7 TurboMax finally gets the 10-speed. ZR2 moves to standard 35s with front and rear lockers. Over 60 inches of dash display on ZR2 and High Country, passenger screen included. Seven trims, three lifted from the factory: ZR2, Trail Boss, and a new Custom Trail Boss.   So let's get into it: 5.7 and 6.6 instead of holding out for a 6.7. Right call? Killing the LT name after all these years: bold, or a mistake? Does the new look land for you, or is it too safe? No power numbers at reveal. Smart tease, or frustrating? What are you ordering on day one?   Drop your first impressions below. 
    • RyanbabZ71
      Gas Prices

      By RyanbabZ71 · Posted

      LOL west coast they need to see what the midwest actually has.  We have been holding at 2.99 for a few weeks now.  Even by work they have come down to 3.02 for the past week.
    • No F-bdy Bs
      Brand new to this forum. Questions about re-gearing my 26’ HD

      By No F-bdy Bs · Posted

      Diesel or gas?  The 37s will obviously, drastically reduce mpg, but the gasser will take a bigger hit to mpg, and power.  Rough guess, but I'd estimate at least a  2mpg hit on the diesel, and up to 4on the gasser. Maybe more.    I wouldn't sweat a gear change on a duramax at all, and unlikely on the gasser either. You're obviously not concerned with acceleration or towing, and the 10spd will find itself in the right gear without much hunting, if any.    If towing, mpg and acceleration are a concern, you're doing the wrong mods.  Either leave it alone, or do the lift/tires and let the chips fall where they may. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      I understand. It is disturbing to think a manufacture asks so much and gives so little in engineering support. This is not a GM issues, this is a greed issue and one the ALL practice.    My intent was not to remove the wind from anyone's sail but rather to point out the areas deficient so that they can be discussed with improvements the goal. But to do that you have to know the truth and what that truth is.    The commercial interest are honed in on a few select issues in which they control all the variables and are not forthcoming in the least with their customers about the details. Failure is the only thing that drives these people to improvement. One way not to fail it to manage public "expectations". The set a bar they can clear and put their thumbs under the suspenders with chest puffed.... Only the internal data tells the story fully. As we don't have access to that for decades then we have to generate it ourselves. UOA's with data that matters.  
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      I had skimmed through that article when you posted the link and honestly I felt rather defeated in a sense and realized that all these years in changing oil that in fact putting in what I was told was a good quality oil was probably not filtered as well as it should be although the filter put on the engine would be what ( as long as it never went into bypass mode ) would be the final filtering of the new oil that the engine components would first see, but then the filtering media itself is not up to par to what is ideal because a full flow filter would be too restrictive to filter fine enough for the engines best outcome in the long run. Only one of our tractors over the years which was a Versatile with a 855 Cummins had a separate bypass filter, some engine manufacturers did spec a partial bypass system within the main oil filter but I don't believe any other trucks or equipment I was servicing used such a filter. No doubt a product like the Amsoil bypass system is of benefit as long as nothing goes sideways with the extra plumbing and filter such as a rupture/leak that could cause the oil to pump out of the engine ( yes that Versatile had a remote canister with hoses routed to it as well ). With the idiot egr system on a diesel and as a result forcing a lot more soot into the oil, that certainly isn't helping the diesel engines cause or as you pointed out the GDI engine issue with creating more soot and aside from having a fancy secondary filtering system, changing the oil more often helping lower the total soot load.     So oil manufacturing and the end product is not something one can control and I wonder if there are specs on what various oil packaging companies produce in particle count or size. As to the filtering, if the OEM is not designing a filter size and spec that is really what it could be, they too are short changing the end user and so what is the answer. Of course as you say the oil side can only do so much if the air side isn't keeping up its end of the picture and air filters are only so efficient and if in a dusty environment such as farm or construction or driving gravel roads there is a lot of dirt to filter out and some of that ends up into the air stream.    Of course the irony in places like where I am where they dump the salt on the highways but also will mix in some calcium or outright pure calcium for problem road area's, or using calcium as dust control on gravel roads, the vehicle that gets used in that environment may rust out before a properly engineered engine and maintenance finally wears out so one has to face that reality in the rust belt. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...