Jump to content

Radar Detector Install

clayp

By clayp
in Modifications & Accessories

 Share

Recommended Posts

clayp Enthusiast

clayp

Posted
Posted (edited)

This is for the 2014 Sierra/Silverado 1500

 

Ok I decided to hardwire my Valentine 1. The install should work for any detector. Others have noted that they could not find a 12v lead off the rear view mirror, so I tried the overhead console.

 

The console (I have Homelink) pops off very easily. You open the sunglass compartment halfway and you can pry open the edge of the console with just your fingers. You should now see this:

 

photoa_zps881715fc.jpg

 

There are three connectors to the console panel: 1 at the front (small black) is for the Homelink buttons, the middle connector (black) is for the LED ambient light, the rear one (brown) is for the interior light switch for the doors.

 

photob_zpse2d8448c.jpg

 

I tested all three connectors and could only find a good 12v + and - at the rear connector for the interior light switch. The left most yellow wire is 12v + and the right most black is - . The yellow wire is triggered with door opening and stays on until all accessory power shuts off. When you lock the car it shuts quickly, otherwise is remains on for maybe 20 sec

 

I used vampire taps and wired in the Valentine harness. The cord to the detector easily wedges thru the front of the console out to the area around the rear view mirror. There is also tons of room to stow away any wiring up there.

 

All tapped in and powered right up:

 

photo_zps42a9cc0b.jpg

 

For tools, the connectors need a small screwdriver to release the clips, and otherwise the only other thing required is taps and a voltmeter. Takes 30 min max

Edited by clayp
  • Like 2
  • Replies 86
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

clayp
clayp

Well disregard the previous post - as is the radar detector will not work in the daytime lol! It only works when the nighttime ambient light is triggered.   Back to the drawing board. I removed the

rdtpp1991
rdtpp1991

I installed the Blendmount and MirrorTap for my V1 tonight...took about 15 mins. If you have powered OnStar mirror and no lane departure it is really easy. There is a harness in cover that goes from

TXTruk15
TXTruk15

you should be able to pop off the whole cover, not just the #2 part, that will get you to the plug easier....   check this out...about 35 seconds into the video....  

Posted Images

clayp Enthusiast

clayp

Posted
  • Author
Posted

Well disregard the previous post - as is the radar detector will not work in the daytime lol! It only works when the nighttime ambient light is triggered.

 

Back to the drawing board. I removed the old setup and this time removed the entire overhead console - not just the panel. There are two T10 screws to remove:

photoc_zps47004e04.jpg

 

Then there are two friction fit tabs up front that just pull straight down.

photoe_zpsae21bf9b.jpg

 

There is a main wiring harness to the overhead console on the left side that you can disconnect.

photod_zps8daa614c.jpg

 

Testing all the wiring shows that the black wire is a good ground, and the leftmost purple wire with white stripe is a good 12v positve that directly is triggered by the ignition. Engine on, power on; engine off, power off.

photof_zps8e5450cb.jpg

photog_zpse3882599.jpg

 

Just an extra step but now all seems to work properly. I think the purple wire with white stripe is the power lead to the passenger airbag light on the overhead console.

  • Like 5
  • 3 weeks later...
jcchevy Enthusiast

jcchevy

Posted
Posted

Very nice write up. I plan on picking up a V1 later down the road as well. I see it retails for $399, did you find it cheaper and if so can you provide the link/store source? Thanks man.

MikeNH Senior Enthusiast

MikeNH

Posted
Posted
Very nice write up. I plan on picking up a V1 later down the road as well. I see it retails for $399, did you find it cheaper and if so can you provide the link/store source? Thanks man.

 

 

Unless you do as Won suggested you won't find a better price unless you buy used. Not sure you can get them anywhere but the manufacturer. If you live near them (Cincinnati I think) you can even pick it up in person, or at least you used to be able to.

  • 1 month later...
SSLS2TB Enthusiast

SSLS2TB

Posted
Posted

Excellent write up. Seeing how to remove that console was priceless. This helped me tremendously. :cheers:

Rkparker Enthusiast

Rkparker

Posted
Posted

I was able to get ignition on/off 12v at the mirror harness with the purple and green wire. Black was still ground. If using mirror tap I would get 15" with nano width for pin.

bigsapper Enthusiast

bigsapper

Posted
Posted (edited)

Do you have a pic of your console? I have the regular cab and it didn't come with Homelink. I'm thinking I should be able to get the panel with the homelink buttons and be GTG, right?

 

Nevermind. There is no wiring run for the Homelink.

Edited by bigsapper
JAF1 Enthusiast

JAF1

Posted
Posted

Has anyone tried running a wire along the headliner, down the A pillar then into the fuse box? That's the way I had my last one wired but I didn't have an airbag in the pillar to worry about.

ctostrowski Enthusiast

ctostrowski

Posted
Posted

Has anyone tried running a wire along the headliner, down the A pillar then into the fuse box? That's the way I had my last one wired but I didn't have an airbag in the pillar to worry about.

yes I did no issues.

JAF1 Enthusiast

JAF1

Posted
Posted

yes I did no issues.

 

Did you pop off the cover or were you able to just tuck in?

ctostrowski Enthusiast

ctostrowski

Posted
Posted

 

Did you pop off the cover or were you able to just tuck in?

I followed the headliner tucked it in the arm and then next to the door gasket. I never removed any of the plastic covering

KUUG Enthusiast

KUUG

Posted
Posted (edited)

This can also be done through an auto dimming mirror with a lot less work. Thats the way I did mine anyway

Edited by KUUG
sh00ter Enthusiast

sh00ter

Posted
Posted

I had planned on hooking up my Valentine One using an Invisicord as I have on lots of past vehicles. It just connects to the plug on the rear of the auto dimming mirror. But, my Denali has the Lane Departure Warning option & there is a box in front of the mirror that houses the cameras it uses. There is no plug to tap into.

 

Has anyone done this hard wire hookup on a truck with the Lane Departure Warning? If so, does it work the same way?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Tyler Gibbs
      Travel Trailer 2024 2500 HD 6.6 Gas Engine ?

      By Tyler Gibbs · Posted

      The curb weight on a 1 ton crew cab long bed is around 7k lbs.  Now, I don't know where you went to school but 9k is not more than 2x 7k lbs. More than 2x 7k lbs would be 14k+.   With that said, obviously yes you're going to feel a 9k lb trailer when slowing down.  I already said, when accelerating.  When changing lanes?  No.  But if you look at the context of what was quoted, the original person said, "after a mile or two..." which means that would be after the accelerating portion and you're driving a generally steady pace.  Please do learn to read and comprehend.
    • sFrank
      2026 Silverado Range AFM DFM ECU loaction

      By sFrank · Posted

      So I purchased the Range unit for my 2026 and I am seeing different locations suggested for the ECM . Can anyone confirm wither under hood, left side or right side or behind the wheelwell?
    • No F-bdy Bs
      Dave's Auto (custom engine builder) tear down of L8T

      By No F-bdy Bs · Posted

      Like I've said before. Di and Carbon buildup is not that big of a concern. Engine had minimal buildup, and that engine was obviously not super well maintained. Do regular oil changes, and you're gtg as long as the rest of the truck lasts. Also, the High Pressure FP that people ****** about, but can't tell you why.  Now, I wish they'd trash the variable oil pump. No real world issues with them, but I'll gladly eat whatever miniscule MPG it's saving me in favor of more oil at all RPMs.    Curious to see his assessment of the 7.3 compared to the 6.6. I expect he'll praise the port inj, but from a structural standpoint, the 6.6 is as robust as any engine out there.    Not to take away from the 7.3. I feel it's equally as good as the 6.6.     As to heat on the rear cyls, I'd have to see numerous examples before I'd say it's an issue. Especially not knowing the history of that engine. For all is known, they could have blown a rad hose, and ran it hot, and the 2 rear cyls may be the first to get hot in a low coolant situation, but not be an issue aside from that. 
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      "Life is getting back to normal."    I'm driving again and all new joints are operating as expected for this stage of recovery.   My most recent joint replacement still requires a lot of attention but experience has taught me that time will quiet the remaining pain.  I joked with my surgeon that another joint replacement would take my mind off my most recent surgery and he responded by saying the next will be a hip!  There are no plans for another surgery but, unlike me, I don't think he was joking!  I certainly wouldn't refuse further replacement  if required but hope to spend time out of the "post-op"  period.  I can't stress enough that if you have been recommended for total hip, knee or shoulder replacement that you welcome the offer.  Post-op "recovery" may sound daunting and painful, however, this is far better than the insidious erosion of mobility you are currently experiencing.  Imagine what it would feel like to wake up most mornings feeling better and more mobile than you did the previous day!  Prior to my first surgery in June 2025, even getting out of bed was becoming a formidable task.  Since the day after my first surgery, I get out of bed everyday easily and unassisted.  Making the switch to feeling a little better each day rather than a little worse, is hugely motivating!
    • Coastie05
      ‘25 Silverado purchase- back to dealership for bumper/radio issue

      By Coastie05 · Posted

      Hope it all works out for you. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...