Jump to content

Voltage gauge on the high side???

gone_fishing
 Share

Recommended Posts

gone_fishing Enthusiast

gone_fishing

Posted
Posted

I've only had my new Sierra a couple weeks now but have noticed that the voltage gauge usually seems high (to me at least). When first started up in the morning the needle is far enough to the right of center that I can see the entire number 14 on the gauge. I have a Scan Gauge so I pluged that in too see what it says. I was seeing readings as high as 15.2 volts when driving this afternoon. It was about 34F today so is their a relationship between higher voltage and cold weather?

 

Thanks

DaveH71 Enthusiast

DaveH71

Posted
Posted

Its supposed to do that. GM has been using variable charging alternators for awhile now. The needle will dip as low as 13.5 and as high as 15 or so. The gauge isn't very precise. The PCM will dial back the alternator when full amp production is not needed to save fuel such as a deceleration event or when not many accessories are on. It will increase amperage output when a high draw is seen such as when a lot of accessories are on etc.

 

Your truck is A-ok and is working exactly how it is supposed to.

newdude Senior Enthusiast

newdude

Posted
Posted

The charging system is basically computer controlled. It can boost or drop charge based on current system voltage, temperature, etc. The system voltage varies with duty cycle. The more % duty cycle, the higher the voltage output.

mcnwil Enthusiast

mcnwil

Posted
Posted

I have been watching my volt gauge and wondering why the swings from 13-15 with no apparent reason. This makes sense now, thanks for the information. These gauges seem pretty accurate to me. They are certainly better than the Ford dummy gauges!

DanielAcosta Enthusiast

DanielAcosta

Posted
Posted

What I have noticed is the voltage is higher after the truck has sat for a few days. Once the battery is fully charged, the voltage drops down. Makes sense and I like it.

 

One of the reasons I decided to trade my 07 Tundra is the voltmeter started fluctuating for no apparent reason. When it sits at one spot for years and then starts to change, something is amiss. The dealer checked it, found no problems and said don't worry about it. I was still concerned, though, because alternator replacements on Tundras are pricey.

  • 6 years later...
Kenk New Member

Kenk

Posted
Posted

I have a 2016 Silverado and my voltage gauge won’t go back down to 0 when the truck is off. It will go down to 15 and the stay way above 19 when I’m driving it  

JimCost2014 Senior Enthusiast

JimCost2014

Posted
Posted
1 hour ago, Kenk said:

I have a 2016 Silverado and my voltage gauge won’t go back down to 0 when the truck is off. It will go down to 15 and the stay way above 19 when I’m driving it  

Welcome to the site.

 

Sounds like your needle is "off", there was just a post from another member where his temp gauge is off in the same manner.

JimCost2014 Senior Enthusiast

JimCost2014

Posted
Posted
1 hour ago, Kenk said:

Do you know how to fix it 

This is what I found:

 

On 7/4/2020 at 2:19 PM, MartyMinogue said:

Hi,

I just noticed something strange happening with my temperature gauge. It seems like the needle is not pointing in the correct direction. I’m attaching a video to show what it looks like. Any help would be greatly appreciated!

 

 

Yes, the needle has moved for some reason. I have seen this multiple times. The good thing about this is it is an easy fix. Remove the cluster and take the outter glass off. reinstall the cluster and turn the igntion on when the engine is completely cold. Remove the needle by GENTLY prying up on it and put it back at 0. Test it to make sure its working correctly and then reinstall the glass.

Very easy repair.

  • 1 year later...
mikeyk101 Senior Enthusiast

mikeyk101

Posted
Posted
On 2/24/2022 at 10:52 AM, Henry Krencis said:

Good luck fishing

Amazing and extremely insightful first post. Did you join just to post this??? 

pokismoki Senior Enthusiast

pokismoki

Posted
Posted

the truck alternator has a special charging algorithm,  by charging at 15.4 volts this blows off sulfides and balances each cell in the battery. it shouldnt charge this high for more than 45 minutes

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Gas Prices

      By Atlas · Posted

      Welcome back! No, it definitely doesn't pass the sniff test. Even "ceasefire" needs an alternative definition these days.    $5.29 at Kroger today
    • bluev8
      Intermittent no-code issues on 2022.5+ V8 trucks — what did the shop fail to capture?

      By bluev8 · Posted

      That makes sense, and I think you are describing the real product problem. Capturing data is the easy part. If the owner or technician has to manually dig through five minutes of millisecond-level logs, the product has already failed. The device would be at the ECM harness, not at the OBD port, so I agree that data retrieval and event marking need to be thought through carefully. The way I am thinking about the architecture is: The recorder itself should not depend on a phone, app, Bluetooth, Wi-Fi, or cloud connection to capture the event. It should always keep a local rolling buffer and lock the event locally. A button, phone app, or small cabin device would only act as an event marker. If the driver feels a stumble and presses the button 10–30 seconds later, the pre-buffer has to already contain the useful data. For data retrieval, the practical options would be a sealed service USB lead, Wi-Fi download, or a phone/cabin companion device. I would not expect the owner to remove the ECM-side module or work with raw files directly. The cloud or AI side would be for interpretation, not for capturing the event. The truck may have no connection when the issue happens, so the evidence has to be saved locally first. After that, cloud processing could help decode the data, compare it against baselines, and generate a readable report. For the first version, I would keep the automatic triggers conservative and objective: driver event marker bus-off error passive voltage drop / brownout device reset FIFO or queue overflow a normally periodic message disappearing side-to-side communication mismatch, if the topology supports that For “learning normal,” I agree with your point, but I would not want to overclaim it as automatic root-cause diagnosis at first. A realistic first step would be learned baseline comparison for that specific vehicle and operating condition. For example, a value would only be compared against similar conditions: RPM range load / MAP throttle position gear / vehicle speed coolant and oil temperature battery voltage AFM/DFM state, if decoded and validated Then the report could flag things like: this periodic message disappeared compared with its normal timing this value deviated from this vehicle’s normal range under similar conditions the same abnormal pattern repeated after the same type of event the anomaly occurred together with voltage, oil-pressure, misfire, or communication changes But I would still call that “abnormal pattern detected,” not “replace this part,” unless there is enough validated repair data behind it. So the intended product would not be “here is a huge log.” It would need to be an event package: what triggered the capture how much pre/post data was preserved what changed before and after the event whether the device itself reset, overflowed, or saw a bus error selected graphs around the event raw data only as supporting evidence From your perspective, what would make this kind of report useful instead of just another datalog? For example: What are the top 5 parameters or events you would want highlighted first? Would you trust a learned baseline for that specific vehicle, or would you prefer fixed thresholds? How much false-positive flagging would be acceptable before you stopped looking at the reports? What would a one-page report need to show for an independent shop to take it seriously? For misfire, AFM/DFM, oil pressure, or U-code complaints, what would you want the tool to flag automatically?
    • scotthvac.net
      2022-24 halogen - led grille swap

      By scotthvac.net · Posted

      2024 Silverado 2500 HD LTZ grille no camera Parts list   84603331 84913656 84913657 84913654 84913655 84911567 84911568 85646092 85646093 85797921 85797922   11570637  x10-15   grille/bumper bolts 11546500  x10      grille clips 11571006  x10      push/retainer clips 11546454  x6       nut retainers 11611609  x6       M5 bolts 11610700  x6       molding/trim retainers
    • davester
      Replacement Radiator

      By davester · Posted

      And use RA's 5% discount code if you buy from them.  google for the code, one is always available.
    • davester
      Turning radius

      By davester · Posted

      Just don't turn the steering wheel as much?

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...