Jump to content

Voltage gauge on the high side???

gone_fishing
 Share

Recommended Posts

gone_fishing Enthusiast

gone_fishing

Posted
Posted

I've only had my new Sierra a couple weeks now but have noticed that the voltage gauge usually seems high (to me at least). When first started up in the morning the needle is far enough to the right of center that I can see the entire number 14 on the gauge. I have a Scan Gauge so I pluged that in too see what it says. I was seeing readings as high as 15.2 volts when driving this afternoon. It was about 34F today so is their a relationship between higher voltage and cold weather?

 

Thanks

DaveH71 Enthusiast

DaveH71

Posted
Posted

Its supposed to do that. GM has been using variable charging alternators for awhile now. The needle will dip as low as 13.5 and as high as 15 or so. The gauge isn't very precise. The PCM will dial back the alternator when full amp production is not needed to save fuel such as a deceleration event or when not many accessories are on. It will increase amperage output when a high draw is seen such as when a lot of accessories are on etc.

 

Your truck is A-ok and is working exactly how it is supposed to.

newdude Senior Enthusiast

newdude

Posted
Posted

The charging system is basically computer controlled. It can boost or drop charge based on current system voltage, temperature, etc. The system voltage varies with duty cycle. The more % duty cycle, the higher the voltage output.

mcnwil Enthusiast

mcnwil

Posted
Posted

I have been watching my volt gauge and wondering why the swings from 13-15 with no apparent reason. This makes sense now, thanks for the information. These gauges seem pretty accurate to me. They are certainly better than the Ford dummy gauges!

DanielAcosta Enthusiast

DanielAcosta

Posted
Posted

What I have noticed is the voltage is higher after the truck has sat for a few days. Once the battery is fully charged, the voltage drops down. Makes sense and I like it.

 

One of the reasons I decided to trade my 07 Tundra is the voltmeter started fluctuating for no apparent reason. When it sits at one spot for years and then starts to change, something is amiss. The dealer checked it, found no problems and said don't worry about it. I was still concerned, though, because alternator replacements on Tundras are pricey.

  • 6 years later...
Kenk New Member

Kenk

Posted
Posted

I have a 2016 Silverado and my voltage gauge won’t go back down to 0 when the truck is off. It will go down to 15 and the stay way above 19 when I’m driving it  

JimCost2014 Senior Enthusiast

JimCost2014

Posted
Posted
1 hour ago, Kenk said:

I have a 2016 Silverado and my voltage gauge won’t go back down to 0 when the truck is off. It will go down to 15 and the stay way above 19 when I’m driving it  

Welcome to the site.

 

Sounds like your needle is "off", there was just a post from another member where his temp gauge is off in the same manner.

JimCost2014 Senior Enthusiast

JimCost2014

Posted
Posted
1 hour ago, Kenk said:

Do you know how to fix it 

This is what I found:

 

On 7/4/2020 at 2:19 PM, MartyMinogue said:

Hi,

I just noticed something strange happening with my temperature gauge. It seems like the needle is not pointing in the correct direction. I’m attaching a video to show what it looks like. Any help would be greatly appreciated!

 

 

Yes, the needle has moved for some reason. I have seen this multiple times. The good thing about this is it is an easy fix. Remove the cluster and take the outter glass off. reinstall the cluster and turn the igntion on when the engine is completely cold. Remove the needle by GENTLY prying up on it and put it back at 0. Test it to make sure its working correctly and then reinstall the glass.

Very easy repair.

  • 1 year later...
mikeyk101 Senior Enthusiast

mikeyk101

Posted
Posted
On 2/24/2022 at 10:52 AM, Henry Krencis said:

Good luck fishing

Amazing and extremely insightful first post. Did you join just to post this??? 

pokismoki Senior Enthusiast

pokismoki

Posted
Posted

the truck alternator has a special charging algorithm,  by charging at 15.4 volts this blows off sulfides and balances each cell in the battery. it shouldnt charge this high for more than 45 minutes

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • asilverblazer
      Intermittent no-code issues on 2022.5+ V8 trucks — what did the shop fail to capture?

      By asilverblazer · Posted

      Length/amount of data capture will be important to consider, sifting through 5 minutes of a data log can be enormous when it is stored in milliseconds. Being able to find the 'event' let alone decipher it.   Presumably the driver would notice something and hit a button to capture the 'window' of data. That window has to be large enough for the operator to recognize the event and react accordingly.    The data has to be able to be retrieved easily.   The data has to be able to be understood. Which is the biggest challenge, dealer techs won't even know what most of it is and would likely not even look at it if an owner brought it to them. Meaning the owner, the least educated/qualified, trying to understand it.    How will the data be presented? Could specific PIDs be selected and a timelapse graph be watched? How will a specific value be noted as abnormal? Additionally, a good data logger would be able to 'learn' normal values for a specific vehicle and flag abnormalities automatically. It could in theory watch parameters degrade over time and suggest maintenance as needed. (If the MAF reading begins tapering off for a given set of other readings - MAP, throttle position, Ambient, etc.. a flag to check air filter.) With the amount of data available, a device (really the vehicle rather than an additional accessory) should be able to do more than issue a DTC. It should be able to run the full diagnostic suite automatically and present a solution rather than a code. (It's not the 90's anymore). The technology is available for the vehicle to not just say "P0087", it should know low fuel pressure, check other PIDs to narrow down the problem itself, and determine if it is a lift pump, high pressure pump, regulator, leak in the fuel line, clogged filter, etc. Even if it can't narrow it down, it should be able to guide the user to the likely problems.   This would be a major problem for dealer service departments, which are the manufacturers customers it is in their collective best interest to NOT have this available to the consumer.   Further, if the owner is going to be the primary consumer of the data, it's got to be at a consumer price point vs. dealer only specialty tool price.   This group is more 'involved' in their vehicle than general public/consumer and will have knowledge, experience, needs and desires that are quite different from the market at large.   
    • KARNUT
      OCI, not when but why?

      By KARNUT · Posted

      I put the prof up. If you read what I posted. You can see that housing, cars and income are in line with the era we were talking about. It’s harder in some places easier in others. Let’s agree to disagree and put this back on track, OK? We both are pretty stubborn and hard headed. But I bring receipts. If you wish I will not respond to you in the future. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      Lets see if I can sum up two pages of nothing useful.    You want to refute your own governments data of the "Purchasing Power" Index FOR THE ENTIRE USA and its territories replacing it with the experience of a single family and its business and label that reality?  Then pound on that for a week hoping it will find traction?    Stan, I've told you several times. I don't do irrational. There are more people in the USA than your family.    I'm pretty sure this tread is so blown up. I'll give you a few days or months if need be to post yourself silent then I'll see if I can find enough parts of the train to reassemble it. 
    • asilverblazer
      VSE CCV Bypass - Anyone have this installed in their L5P?

      By asilverblazer · Posted

      Facebook groups hate VSE, poor customer service; their responses to criticisms are pretty poor for a reputable company. I'm not a customer, haven't bought anything from them, but how they handle themselves on social media is a definite "No" for me. 
    • asilverblazer
      Transmission Woes :-(

      By asilverblazer · Posted

      $10,000 for a transmission?   Pretty sure I could buy all the parts, tools, and education to rebuild it myself for a quarter of that amount.   or swap it out with a new one...

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...