What have you done to your K2 today?

[Daly]

Installed an OEM tonneau I picked up for $250. It's keep the snow out until I get a topper next summer.

[Michael71009]

Here it is on the truck. I outlined it in brown but...on black tint it's hard to see. The badge is just for reference. Not to bad I don't think for my first time cutting a decal.

Sent from my SAMSUNG-SM-G890A using Tapatalk

[TeamsterGene]

Here it is on the truck. I outlined it in brown but...on black tint it's hard to see. The badge is just for reference. Not to bad I don't think for my first time cutting a decal.

Sent from my SAMSUNG-SM-G890A using Tapatalk

That looks SWEET!


Sent from my iPhone using Tapatalk

[jdrampage]

On ‎10‎/‎14‎/‎2017 at 8:43 PM, gruve said:

New upper control arms from rough country since the 2.5 level/lift blew my passenger side ball joint after 20,000 miles


Sent from my iPhone using Tapatalk

I think you just convinced me not to go with RC

[gruve]

I think you just convinced me not to go with RC

Gotta pay to play I guess. The 2.5 inch kit from anywhere is going to jack up the ball joint angles.


Sent from my iPhone using Tapatalk

[jdrampage]

Very true. I keep going back and forth between a 4" and 6" lift. I love the looks of a 6" but the truck is my daily driver and I drive 70 miles round trip for work mon-fri

[jdrampage]

I replaced my reverse lights and my license plate lights with LEDs

 

[jdrampage]

Here's a shot of it all together. Mind you, this is mid-day in my garage. Those puppies are BRIGHT at night!

[Michael71009]

Here's a shot of it all together. Mind you, this is mid-day in my garage. Those puppies are BRIGHT at night!

Which leds did you use for your reverse lights?

Sent from my SAMSUNG-SM-G890A using Tapatalk

[jdrampage]

 

20 minutes ago, Michael71009 said:

Which leds did you use for your reverse lights?

Sent from my SAMSUNG-SM-G890A using Tapatalk
 

https://www.amazon.com/dp/B00K3GBRQ2/ref=cm_sw_r_cp_apa_mQK5zbE8QTN55

[T_ClarkEx39]

Good luck with the JDM. My last truck I went through 5 sets and finally gave up on them. 

[jdrampage]

21 minutes ago, T_ClarkEx39 said:

Good luck with the JDM. My last truck I went through 5 sets and finally gave up on them. 

How long did yours last? I've only had mine in for 2 months but no problems

[T_ClarkEx39]

1 hour ago, jdrampage said:

How long did yours last? I've only had mine in for 2 months but no problems

Between 2 and 4 months they would start flickering. That was on a 2003 Duramax so I don't know if anything has improved with the new electronics on these new trucks or not. But when I got ready to put my LED reverse lights in this 2017 2500 I went with a different company. they have been in here for about a month now, they were a little bit more expensive than the jdms were, so we will see how these do. The Chinese folks over at JDM I would actually talk to on the phone, and of course you know how that goes, they could barely speak English but they kept sending me new ones and within 2 to 4 months they would start flickering again so I finally just gave up.

[Goinovr]

I've had my reverse lights almost over a year and they are glowing strong. License plate lights are a few months old but still good. I just make sure I get the cob based LEDS with full connection tabs vs the diode/cob LEDS with single wire connectors.

[T_ClarkEx39]

4 minutes ago, Goinovr said:

I've had my reverse lights almost over a year and they are glowing strong. License plate lights are a few months old but still good. I just make sure I get the cob based LEDS with full connection tabs vs the diode/cob LEDS with single wire connectors.

JdM's or a different brand?