Jump to content

Foglights On With High Beams

Spurshot
 Share

Recommended Posts

  • Replies 796
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Spurshot
Spurshot

2014 SIERRA SLT FOG LIGHTS WITH HIGH BEAM HEADLIGHTS MODIFICATION This mod will let you use the fog lights on low beam same as factory. On and off with the fog light button. When the fog ligh

Spurshot
Spurshot

This was on the Duramax forum. I believe it is for a GMT 900. But the principles are likely applicable to a K2. Use this information cautiously. ------------------------------------------------------

Spurshot
Spurshot

OK, After struggling thru the schematics and online mods of past models all evening, I figured it out. This is for a Sierra and should be the same for the Silverado. It involves pushing one Diode in

Posted Images

  • 2 weeks later...
SlavO Enthusiast

SlavO

Posted
Posted

I put these in today... could someone bump the mod with your cargo and reverse lights on the same time... please 4e3ce8de9c411d5abeedcdda6fab0ac1.jpg

 

Sent from my SM-G930V using Tapatalk

  • Like 1
  • 3 weeks later...
pgamboa Senior Enthusiast

pgamboa

Posted
Posted

I can't get this too work for the life of me. Maybe I'm just a fatass

If you're having trouble inserting the diodes, try a different corner within the slot. The connector has a locking tab within it that might block entrance into the slot.

 

 

Sent from my iPhone using Tapatalk

Trippstarr Enthusiast

Trippstarr

Posted
Posted

I think I'm just a big dude and can't position myself properly to get in there to look at the slot. I can get the first diode in but to connect it to the middle slot where all the wires are is alittle tougher. Lol oh well.

6.2Midnight Enthusiast

6.2Midnight

Posted
Posted (edited)

If you read through this topic, you will see that you are not alone. Different owners have tried different ways to install the diodes. Try them until you find the one that works for you. To start, you may want to unplug the connector if you haven't tried that already.

 

I have pretty good sized hands, and been working on cars for about 30 years, maybe try a small pair of needle nose plyers to get in and around the other wires?

Edited by 6.2Midnight
  • Like 1
pgamboa Senior Enthusiast

pgamboa

Posted
Posted

It is a tight squeeze to position yourself underneath there. I spent a lot of time in that area for other projects.

 

 

Sent from my iPhone using Tapatalk

  • 2 weeks later...
Crstfr Enthusiast

Crstfr

Posted
Posted

man i tried this last night... i could not get it to work!!!..grrr.. i used 2 trying.. and could not get the fogs to stay on.. i did brown with white stripe and brown with purple stripe like op said.. in the brown plug.. i felt like they where pushed down far enough... i'll just have to give it another shot.. .. lucky i got 25 of them suckers! lol.. easy to bend.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,915
    Total Members
    8,960
    Most Online
    ChristopherDobson
    Newest Member
    ChristopherDobson
    Joined

  • Who's Online   0 Members, 0 Anonymous, 1,361 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • ChristopherDobson
      Vehicle Payments

      By ChristopherDobson · Posted

      Monthly payment is only part of the equation. With today's prices and interest rates, I'd look at the total monthly cost: payment, insurance, registration, fuel, maintenance, and expected repairs. A vehicle that fits comfortably into your budget is usually the better choice than stretching for a higher trim. I've also kept my vehicles longer over the past few years. New cars have gotten expensive enough that driving one for 10+ years, while staying on top of maintenance, often ends up being the most cost-effective approach.
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      10 Ford and Chevy engines proven to reach 300,000 miles   You may note a common 3K OCI on this list of gas motors. I skipped over the diesels. Dh'O. 
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      Thanks newdude!  By the time manual selection is needed, I'm probably too much of a control-freak to depend on the transmission sensing braking to activate automatic downshifting.  I would be anticipating the situation and already be manually downshifting.   This truck replaced a 2004.5 LLY diesel with the Allison 5-speed.  Putting it in T/H made noticeable differences (when the torque converter locked, upshift points, downshift behavior).  On this 2024 gasser with the 10L1000 I haven't been able to detect much, if any, difference.  Ok, I can never tell now when the torque converter locks up.  But I also don't notice differences in shifting.  For downhills, I've probably already manually downshifted by then anyway.  Since it's also more awkward (than the 2004.5) to engage/disengage I don't even bother.  Or maybe it doesn't really matter with just a 3k lb. camper in the bed?   Thanks also for the list of reasons the charging system might select various voltages.  However, what I am seeing doesn't fall into any of those categories.  It very definitely, and very consistently, rises after coasting/braking.  Maybe not immediately, but not very long after coasting/braking.  Very consistently drops voltage when no longer coasting/braking.  It might also be interacting with the camper battery charging (I might disconnect the camper and see if it changes the charging behavior).  I also need to recheck turning on headlights for when I want to force it to charge the camper.   Another JR, in June I converted the camper to LiFePO4.  Since it's not a good idea to try to charge lithiums directly using truck, I installed a Victron Orion XS DC-DC charger (which BTW is AMAZING!!).  Being cheap, I only had to buy that one item (besides the battery, of course) to do the conversion.  The camper OEM 120v battery charger (only 19 years old and works perfectly) and the truck feed the input to the DC-DC charger (not at the same time).  But I didn't want the camper charger feeding back to the truck so I kept the old separator.  I considered replacing the separator with a 30amp diode but that means more work and might add another 1/2 volt drop.  One thing that surprised me was the voltage drop over the long 10awg wire run, so I can only charge smoothly at 8 amps (because the DC-DC charger is completely configurable).  Another reason I don't want an added voltage drop with the diode.  I might also be a little lazy but all this work is being done under the sink with a small cabinet opening.    
    • davester
      cam upgrade in CA

      By davester · Posted

      apparently CA smog is (or at least was)  checking that the vehicle is using the oem and/or a ca smog approved tune, so I expect you'll fail inspection doing it.
    • davester
      Possible lifter tick after DOD delete

      By davester · Posted

      yes, leaking exhaust will mess up o2 sensor readings, which in turn messes up fuel trims.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...