Jump to content

Recommended Posts

Posted (edited)

I noticed at 20k the coolant was below the cold fill mark about 3/4" when cold. Filled it back up with distilled H2O. I now have 33K and the coolant is about an inch below the cold fill mark when cold. I investigated to find a slight odor near the top corner of the radiator on the drivers side. I looked closer and noticed that the metal tabs are cracked in this area. I can not see a physical leak yet but can tell its leaking a bit faster. Off to the dealership AGAIN! Problem # I lost count.

post-124852-0-42629900-1451136948.jpg

post-124852-0-42629900-1451136948.jpg

post-124852-0-42629900-1451136948.jpg

post-124852-0-42629900-1451136948.jpg

Edited by fireaxxe
Posted

There is a tsb for that very concern. Needs a radiator and thermostat. Thermostat cycles too much causing stress cracks in the radiator.

Posted

Checked mine 1is broke and one truck is fine.No known coolant leaks. How long will this be covered by warranty?

Posted

Sometimes radiators with plastic tanks develop microscopic cracks that will cause slow coolant leaks, but you will not see the crack with a naked eye. I had a crack like that on the upper hose neck on my Mazda 626 radiator. It happened after 200k miles, and I could see a drop of coolant oozing from the invisible crack. I was loosing about a quart of coolant per month this way.

Posted

For the last month I've been getting cool and smell from the front of my engine with the hood closed when I'm at a drive thru it's a very noticeable the smell just sitting and idling dealer says that no leak I wonder what this Technical Service Bulletin is myself anyone have a link to the bulletin

Posted

I just checked mine the driver side is cracked I looked and shined a flashlight on the passenger side its not cracked but the top of the rad in the core is all wet and leaking

Posted (edited)

Here is a link to a possible wide spread issue.

 

http://oemdtc.com/25613/coolant-smell-andor-slight-leak-at-radiator-2014-2015-cadillac-chevrolet-gmc-vehicles

 

 

Also I checked the part numbers to see what I could expect when it comes to availability of a radiator, just in case I needed to replace mine. I can not find my part number and there are only two others that I can find. It seems as if GM already has a new part number for the replacement radiator.

 

My Current Radiator part #23431774

 

*New W/O Max Tow package Replacement part #23445967*

 

** Possible New W/Max Tow package Replacement part #23126402**

 

(Not sure if the Max Tow Radiator part number was changed as I have nothing to compare it to. Is there anyone with the Max Tow Package that can confirm this?)

 

This number is located on the upper corner of the radiator on the passenger side.

Edited by fireaxxe
  • Like 2
Posted

I just got off the phone with my dealership they looked on my VIN and there is a special repair notice attached to it for this issue I haven't booked in on Thursday and they're giving me a rental truck until it's fixed they also told me there is a fuel sensor that has to be replaced

Posted

I just got off the phone with my dealership they looked on my VIN and there is a special repair notice attached to it for this issue I haven't booked in on Thursday and they're giving me a rental truck until it's fixed they also told me there is a fuel sensor that has to be replaced

What year and model is your truck?

Posted

My crew cab is cracked and double cab is not cracked. Wonder if this is a trend?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.3k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,716
    Total Members
    8,960
    Most Online
    BDS my HD
    Newest Member
    BDS my HD
    Joined
  • Who's Online   1 Member, 0 Anonymous, 476 Guests (See full list)


  • Latest Articles

  • Posts

    • Hello hello looking forward to expanding my knowledge of the 2026 2500 HD that I just bought.   Truck has 3500 miles on it four-wheel-drive crew cab and I’m about to put a 6 1/2 inch BDS lift on it 18 x 10 -25 offset with 37’s   Already have the wheels and tires just waiting on the lift install in about three weeks   Question what surprises am I not gonna be happy with?  I’m not new to lifted trucks so I know that acceleration towing gas mileage all that is affected..   Question is those of you that have this truck this powertrain with a 10 speed Allison and have done the mods that I’m doing,,, how bad is it? Is that Allison constantly gonna be hunting for the right gear to go into? And what about towing, acceleration, fuel consumption as mentioned?    Lastly how come I can’t find any ring pinion gear set up for these axles and when could I expect to see them?   I apologize if there’s any typos I’m doing speech to text on my iPhone.    
    • I've got a 2013 2500 6.0L Flexfuel. Drove the truck earlier today with no issues. Went to run an errand tonight and noticed key fob wouldn't work. Figured battery was dead, so replaced fob batter. Still wasn't working. Grabbed my other set of keys with the other fob and that one wasn't working either. So I manually unlock truck and insert key. Interior lights come on, dashboard lights up, turn key and truck starts. Turn truck off, like a moron, and try starting again. This time no crank, no click, no nothing. Lights still come on and dash lights up, but now I'm getting a service 4wheel drive, service tire monitor, etc. Check voltage on battery and Im showing 12.2v. Throw my battery charger on it and give it 15 mins and try starting again. But still no crank no start. Decide maybe its a bad battery, run to autozone grab a new one and put it in. Same issue. Disconnect battery and let it sit for 15 mins. Try again and still nothing. I had managed to roll the windows down earlier as its a humid night, but now I can't get them to roll up. Power locks are also not working now. Then randomly I try the key again, and it fires right up. Immediately I roll up the windows as we have nothing but rain forecast this week. I shut it back off wait 30 seconds and start up again. Worked a 2nd time. So turn it off, start putting things back together. Try one more time, and back to no crank no start. And now the car alarm starts going off. Had to disconnect battery and leave it that way for the night as I don't think my neighbors would appreciate my alarm going off again tonight. Any thoughts or help would be appreciated. 
    • No one will care for you like you care for you. Do what you can for as long as you can. IMHO of course. 
    • How about them NICKS!!! 
    • Hi there.  Long time lurker, first post.    i have read the previous posts regarding the water ingress problem with this emblem.  I bought my 1500 SLT the  summer of 2025 new and after reading the MANY problems with these emblems failing I decided to install one anyways.  As per a YouTube video, I sealed ( or tried to) this sign with silicone sealant around the outer perimeter joint and the holes that were already somewhat sealed on the rear plate of the emblem.  And installed the connector assembly using dielectric grease on the connectors. The installation looked great and worked well for about 4 months……then FAILURE.  Grrrrrr…… I live in the great white north and wash my truck weekly in an automatic car wash  to keep the salt off.  Let me tell you that removing the old, failed emblem is a whole different animal than removing the OEM individual letters without removing the grill assembly. Mainly because the illuminated logo is built differently than the original letters which  you can remove the red surface lettering with a knife or some kind of blade which gives access to the tabs which hold the logo onto the grill. So I had to essentially destroyed the old emblem to remove it. Doing so killed my chance of doing somekind of autopsy on the failed , old logo.  But there was plenty of water inside when I ripped it apart.  Prior to installing the new assembly I tried it with the old harness and it works fine.   Does anyone have any insight as to where the water is getting into this emblem? I intend to seal the new logo with slow curing epoxy this time around using a syringe.  I think this newer emblem may be an updated unit which I hope GM got the vendor to fix. It has an October 2025 date on it.    If this one  fails,  I am just going to revert back to the non-illuminated letters….AFTER PULLING THE GRILL.    Any thoughts on sealing with epoxy would be appreciated. Thx!   Doug  
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...