Jump to content

Converted to E85

bobbobtar

By bobbobtar
in Modifications & Accessories

 Share

Recommended Posts

bobbobtar Enthusiast

bobbobtar

Posted
Posted (edited)

Just converted my 2016 Chevy Silverado LTZ 5.3L Double Cab to run E85 same as my 2014 GMC Sierra 5.3L. The Chevy did not come from the factory as a flex fuel, but the GMC did, these are the GM parts I used to do the conversion these parts are for a double cab only.

 

20967866 Flex fuel sensor clip

13577429 Flex fuel sensor

23171538 Hose

20967834 Hose

23158923 Pipe

23171537 Pipe

 

If you were to do a Club Cab the two hose's would be different everything else is the same. Did not do a flash as the computer recognized the sensor.

Edited by bobbobtar
  • Like 4
  • Replies 84
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

bobbobtar
bobbobtar

Just converted my 2016 Chevy Silverado LTZ 5.3L Double Cab to run E85 same as my 2014 GMC Sierra 5.3L. The Chevy did not come from the factory as a flex fuel, but the GMC did, these are the GM parts I

bobbobtar
bobbobtar

Seat of the pants, I could tell it was different, felt like it had better acceleration.

transam69230
transam69230

I would completely advise against running e85 in your truck until you get the ECU tuned.

Posted Images

bobbobtar Enthusiast

bobbobtar

Posted
  • Author
Posted (edited)

I'm gonna have to try this. What did the sensor "plug into" to allow the ecm to recognize the sensor?

The harness plug cover has a little plastic stud that holds to the frame (when it's not used) it just below where the sensor plugs into the frame. After you do the install plug the harness connector into the sensor which will tell the computer what the octane number is and make the adjustments.

Edited by bobbobtar
  • Like 1
bobbobtar Enthusiast

bobbobtar

Posted
  • Author
Posted

Forget all that. How does she feel power wise!?

Seat of the pants, I could tell it was different, felt like it had better acceleration.

  • Like 2
Ridersfan Enthusiast

Ridersfan

Posted
Posted

Just converted my 2016 Chevy Silverado LTZ 5.3L Double Cab to run E85 same as my 2014 GMC Sierra 5.3L. The Chevy did not come from the factory as a flex fuel, but the GMC did, these are the GM parts I used to do the conversion these parts are for a double cab only.

 

20967866 Flex fuel sensor clip

13577429 Flex fuel sensor

23171538 Hose

20967834 Hose

23158923 Pipe

23171537 Pipe

 

If you were to do a Club Cab the two hose's would be different everything else is the same. Did not do a flash as the computer recognized the sensor.

You should change your gas cap to reflect it as well. Not that are many full service gas stations left anymore... or people that have common sense... but IF you find both, they may refuse to pump E85 into an unleaded capped tank.

bobbobtar Enthusiast

bobbobtar

Posted
  • Author
Posted

Yes forgot to mention that I did change the gas cap.

  • Like 1
bobbobtar Enthusiast

bobbobtar

Posted
  • Author
Posted

I didn't have time to do the install myself so local shop did the install. From looking at parts, it's all plug and play. The Pipe is short 8" piece of flexible hose that has OEM fitting on it that connects the front and back fuel line to the sensor.

transam69230 Enthusiast

transam69230

Posted
Posted (edited)

Do you not need a tune to turn on the e85 capability? I feel like just adding the sensor would not do anything since you aren't telling the computer to adjust timing/spark for additional octane .

 

http://www.gm-trucks.com/forums/topic/180793-flex-fuel-conversion-everything-you-need-to-know/?do=findComment&comment=1728414

 

It is laid out in the thread above. Carl T is the local GM tuner in MN that I personal use from my race car, and explains that the you need to enable the sensor in the ECU.

Edited by transam69230
  • Like 1
bobbobtar Enthusiast

bobbobtar

Posted
  • Author
Posted (edited)

I would completely advise against running e85 in your truck until you get the ECU tuned.

Would you completely advise against running E85 in a 2016 flex fuel truck? According to my tech. there is no provision on the 2016 trucks to flash or turn on E85 he spent half an hour looking for that option in the ECM and BCM maybe that was an option for 2014-2015 trucks doesn't look like it is now, what Carl was talking about was a 2015 truck.

Edited by bobbobtar
  • Like 1
transam69230 Enthusiast

transam69230

Posted
Posted

So if the truck is a "flex fuel truck" then why didn't it have the sensor already? That indicates that it is not setup for flex fuel in my opinion.

 

If your tech is a GM service technician I would take that with a grain of salt and do your own homework on it.

 

You could certainly be right, but it I'd verify that with a tuner that uses an aftermarket tool such as HP tuners.

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.3k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,739
    Total Members
    8,960
    Most Online
    chfkief
    Newest Member
    chfkief
    Joined

  • Who's Online   2 Members, 0 Anonymous, 1,603 Guests (See full list)

  • Latest Articles

  • Posts

    • Chuck FB
      Joke Thread

      By Chuck FB · Posted

      Fred was in the fertilized egg business. He had several hundred young pullets, and ten roosters to fertilize the eggs He kept records, and any rooster not performing went into the soup pot and was replaced. This took a lot of time, so he bought some tiny bells and attached them to his roosters. Each bell had a different tone, so he could tell from a distance, which rooster was performing. Now, he could sit on the porch and fill out an efficiency report by just listening to the bells. Fred's favourite rooster, old Butch, was a very fine specimen, but this morning he noticed old Butch's bell hadn't rung at all! When he went to investigate, he saw the other roosters were busy chasing pullets, bells-a-ringing, but the pullets, hearing the roosters coming, would run for cover. To Fred's amazement, old Butch had his bell in his beak, so it couldn't ring. He'd sneak up on a pullet, do his job and walk on to the next one. Fred was so proud of old Butch, he entered him in the City Show and he became an overnight sensation among the judges. The result was the judges not only awarded old Butch the "No Bell Piece Prize," but they also awarded him the "Pulletsurprise" as well. Clearly old Butch was a politician in the making. Who else but a politician could figure out how to win two of the most coveted awards on our planet by being the best at sneaking up on the unsuspecting populace and screwing them when they weren't paying attention. Vote carefully in the next election, you can't always hear the bells.
    • chfkief
      FS: Black Bear Performance AutoCal Tuning System

      By chfkief · Posted

      Do you still have?
    • 3CarSeatDad
      High Country Suburban build confirmation

      By 3CarSeatDad · Posted

      Can someone confirm if the GM order workbench terminal is able to validate a custom build sequence:   1) Initialize the Allocation Base: Open a new vehicle build queue, select the 2026 Chevrolet Suburban 4WD, and pick the High Country (3LZ Preferred Equipment Group).   2) Select the Diesel Powertrain: Go directly to the engine configuration screen and choose RPO code LZ0 (3.0L Duramax Turbo-Diesel). Ensure it maps to the MHS 10-speed automatic transmission.   3) Deploy the Seating Swap: Navigate to the Interior Options screen and enter RPO code ATT to replace the standard captain's chairs with the power-release 60/40 bench seat. Because you are not trying to force a separate luxury or air-suspension bundle, the standard, premium D07 Fixed Floor Console remains active. The system will accept this change immediately without triggering a warning message.   3)Apply Heavy-Duty Hauling Capability: Input RPO code NHT (Max Trailering Package). The commercial terminal will automatically bundle the required trailering hardware and software modules to support the diesel engine's maximum towing capacity.   5) Layer the Premium Tech and Glass: Separately add code C3U (Panoramic Power Sunroof) and code UKL (Super Cruise) to the order screen.   6) Run the Final Validation: Click the "Validate Order" button at the bottom of the interface.
    • revmanii
      Looking at ordering a '26 WT because I want a std cab, std bed

      By revmanii · Posted

      Spent the last hour or 2 googling and reading up on the spacer thing. I don't like the loss of thread contact on the slip on spacers, but it appears you can get "extended" lug nuts that reach into the hole of the wheel to get back the lost threads. Looks like the only true hubcentric slip on spacers are at least .375". I'd want as little as I could get away with and don't want to cause other clearance issues going any thicker. Bora seems to offer what appears to be a well made .375" spacer and extended lug nuts. I searched here and did find a couple threads recommending Bora. But not cheap. By the time I buy spacers and lugs, new TPMS sensors, then pay a tire shop to install the new sensors, I suspect I'm going to be in over $400. Thinking about running out and getting some washers to put behind the wheel to see if .375" is enough to clear calipers, turn lock to lock without rubbing, and to see if the wheels/tires look strange pushed out a little. This would just be to check fitment.
    • Core-Lokt
      Road Master Active Suspension

      By Core-Lokt · Posted

      Roadmaster makes some quality parts; I have their sway bar. I considered the RAS, but I ended up bagging. I didn't know what kind of ride I'd get with RAS, and the bags have interior jounce bumpers, so I can run 0 pounds pressure. I figured I'd have the best of normal suspension ride with assist on-demand. But it seems you got pretty much the same in one item.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...